Manuals+

XBA-KHR8 Option Switch Settings

Supported bill: KHR 100, 500, 1000, 2000, 5000, 10000, 20000, 50000 (8 bills).

XBA-KHR8 (Pulse/MDB/ICT002U/ICT104U/ICT104V) Function Settings

FUNCTION SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
Inhibit Active HIGH ON
Inhibit Active LOW OFF
Reserved ON
Reserved OFF
Reserved ON
Reserved OFF
Reserved ON
Reserved OFF
Reject KHR 100 ON
Accept KHR 100 OFF
Reject KHR 500 & 1000 & 2000 ON
Accept KHR 500 & 1000 & 2000 OFF
Reject KHR 5000 & 10000 & 20000 ON
Accept KHR 5000 & 10000 & 20000 OFF
Reject KHR 50000 ON
Accept KHR 50000 OFF
High Acceptance ON
High Security OFF
Disable Bill Reject 4 Times
BA Stop By 30 Sec		 ON
Enable Bill Reject 4 Times
BA Stop By 30 Sec		 OFF
Stack Banknote when Power-up ON
Reject Banknote when Power-up OFF
Reserved ON
Reserved OFF
Pulse Mode
Credit-Pulse Normal HIGH
Scaling Factor (SF) = 100
Decimal Point Position (DPP) = 2		 MDB Mode
Scaling Factor (SF) = 1
Decimal Point Position (DPP) = 0
Connect with ICT JPSTD converter board		 ICT104V Mode
Connect with coin changer
ON
Credit-Pulse Normal LOW
Decimal Point Position (DPP) = 0		 OFF
Pulse Mode
Other Mode		 Pulse Mode Other Mode
1 pulse / KHR 100 (Note.2) / 500 (Note.3) MDB Mode
OFF OFF		 ICT104V Mode
OFF OFF
2 pulse / KHR 100 (Note.2) / 500 (Note.3) ICT002U Mode
OFF ON		 ICT104V Mode
OFF ON
5 pulse / KHR 100 (Note.2) / 500 (Note.3) ICT104U Mode
ON OFF		 ICT104V Mode
ON OFF
10 pulse / KHR 100 (Note.2) / 500 (Note.3) ICT104V Mode
ON ON

This dip switch is located on the CPU board, remove the CPU board cover first.

Diagram: DIP Switch Location

A side view illustration of the XBA unit, highlighting a panel where the DIP switch is located, labeled as (2). An accompanying illustration shows the CPU board with the DIP switch labeled as (1), and an arrow indicating the direction for removing the CPU board cover.

Currency Assign Data

Interface Pulse MDB ICT002U ICT104U ICT104V
LED
Bill value When Dip 1 is ON When Dip 1 is OFF When Dip 1 is ON When Dip 1 is OFF When Dip 1 is ON
BV1 100 100 100 100 500
BV2 500 500 500 500 1000
BV3 1000 1000 1000 1000 2000
BV4 2000 2000 2000 2000 5000
BV5 5000 5000 5000 5000 10000
BV6 10000 10000 10000 10000 20000
BV7 20000 20000 20000 20000 50000
BV8 50000 50000 50000 50000

Appendix: Manufacture Setting

After setting dip switch of the credit pulses, you should reset the bill acceptor again.

Note:

PDF preview unavailable. Download the PDF instead.

XBA-KHR8(Pulse+MDB US+ICT002U+ICT104U+ICT104V) Corel PDF Engine Version 17.1.0.572 CorelDRAW X7

Related Documents

Preview XBA-USD6 Option Switch Settings and Currency Configuration Guide
Detailed guide to XBA-USD6 option switch settings, including pulse, MDB, ICT002U, ICT104U, and ICT104V modes, along with currency assignment data for various bill denominations.
Preview XBA-NZD5 Bill Acceptor: Option Switch Settings and Currency Assignment Guide
Comprehensive guide detailing the XBA-NZD5 bill acceptor's option switch configurations for various modes including Pulse, MDB, and ICT104V. Features currency assignment data for New Zealand Dollars (NZD) and switch location information.
Preview XBA-JMD6 Bill Acceptor Option Switch Settings and Configuration Guide
Detailed guide to configuring the XBA-JMD6 bill acceptor, including option switch settings for various currencies (JMD) and communication protocols (Pulse, MDB, ICT). Covers currency assignment, setup notes, and DIP switch locations.
Preview XBA-TWD4 Bill Acceptor Option Switch Settings and Configuration Guide
Comprehensive guide detailing the XBA-TWD4 bill acceptor's DIP switch settings for various operating modes including Pulse, MDB, ICT104U, and ICT104V. Includes currency assignment data and configuration notes.
Preview XBA-REN11 Bill Acceptor Switch Settings and Configuration Guide
A comprehensive guide detailing the dip switch settings for the XBA-REN11 bill acceptor, covering various protocols like Pulse, MDB, ICT104U, and ICT104V, along with currency assignment data.
Preview XBA-RUB6 Bill Acceptor: Option Switch Settings and Configuration
Guide to XBA-RUB6 bill acceptor option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, including currency assignment data by International Currency Technologies Corporation.
Preview XBA-SGD4 Bill Acceptor Switch Settings and Configuration Guide
Detailed guide to XBA-SGD4 bill acceptor option switch settings, including supported currencies (SGD), interface modes (Pulse, MDB, ICT104U/V, EXRFID), and currency assignment data for optimal operation.
Preview XBA-KZT6 Bill Acceptor Option Switch Settings and Currency Assignment
Detailed configuration guide for the XBA-KZT6 bill acceptor, covering option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, along with currency assignment data.