XBA-REN11 Option Switch Settings
XBA-REN11 (Pulse/MDB/ICT104U/ICT104V)
Supported Bills
RON: 1, 5, 10, 20, 50 (5 bills)
EUR: 5, 10, 20, 50, 100, 200 (6 bills)
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject RON 1 & 5 | ON | |||||||
| Accept RON 1 & 5 | OFF | |||||||
| Reject RON 10 & 20 & 50 | ON | |||||||
| Accept RON 10 & 20 & 50 | OFF | |||||||
| Reject € 5 & 10 | ON | |||||||
| Accept € 5 & 10 | OFF | |||||||
| Reject € 20 & 50 | ON | |||||||
| Accept € 20 & 50 | OFF | |||||||
| Reject € 100(2019) & 200(2019) | ON | |||||||
| Accept € 100(2019) & 200(2019) | OFF | |||||||
| Disable Bill Reject 4 Times BA Stop By 30 Sec | ON | |||||||
| Enable Bill Reject 4 Times BA Stop By 30 Sec | ON | |||||||
| Stack Banknote when Power-up | ON | |||||||
| Reject Banknote when Power-up | ON | |||||||
| Reserved | ON | |||||||
| Reserved | OFF |
Dip Switch Location
This dip switch is located at the side of XBA.
[Diagram: Illustration of the XBA unit with a callout pointing to the dip switch on its side.]
| FUNCTION | SW1-SW4 | MDB Mode | ICT104V Mode | |||||
|---|---|---|---|---|---|---|---|---|
| SW5 | SW6 | SW7 | SW8 | Settings | Settings | Settings | Settings | |
| Inhibit Active HIGH | ON | |||||||
| Inhibit Active LOW | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Pulse Mode | ||||||||
| Credit-Pulse Normal HIGH Scaling Factor (SF)= 100 Decimal Point Position (DPP)= 2 | Connect with coin changer | ON | ||||||
| Credit-Pulse Normal LOW Scaling Factor (SF)= 1 Decimal Point Position (DPP)= 0 | Connect with ICT JPSTD converter board | OFF | ||||||
| Mute Mode | OFF | |||||||
| Other Mode | OFF | |||||||
| Pulse Mode | ||||||||
| 1 pulse / RON 1 | MDB Mode | |||||||
| 2 pulses / RON 1 | Reserved | OFF OFF | ||||||
| 10 pulses / RON 1 | ICT104U Mode | ON OFF | ||||||
| 20 pulses / RON 1 | ICT104V Mode | ON ON | ||||||
Manufacturer Setting
After setting dip switch of the credit pulses, you should reset the bill acceptor again.
Note:
- Please reset the bill acceptor after set the dip switch.
- Dip switches 1 to 5 are only used for pulse protocol.
- Calibration card is needed.
- The transaction Record can be saved by USB MSD (only for EX series)
- EUR $5 display RON 20 (Only for Pulse, MDB)
- EUR $10 display RON 40 (Only for Pulse, MDB)
- EUR $20 display RON 80 (Only for Pulse, MDB)
- EUR $50 display RON 200 (Only for Pulse, MDB)
- EUR $100 display RON 400 (Only for Pulse)
- EUR $200 display RON 800 (Only for Pulse)
Dip Switch Location on CPU Board
This dip switch is located on the CPU board, remove the CPU board cover first.
[Diagram: Illustration of a CPU board with a callout pointing to the dip switch.]
Currency Assign Data
| Bill value | Interface | ICT104U | ICT104V | Pulse | MDB |
|---|---|---|---|---|---|
| BV1 | RON 1 | RON 1 | RON 1 | RON 1 | RON 1 |
| BV2 | RON 5 | RON 5 | RON 5 | RON 5 | RON 5 |
| BV3 | RON 10 | RON 10 | RON 10 | RON 10 | RON 10 |
| BV4 | RON 50 | RON 50 | RON 50 | RON 50 | RON 50 |
| BV5 | € 5 | € 5 | € 5 | € 5 | € 5 |
| BV6 | € 10 | € 10 | € 10 | € 10 | € 10 |
| BV7 | € 20 | € 20 | € 20 | € 20 | € 20 |
| BV8 | € 50 | € 50 | € 50 | € 50 | € 50 |
| BV9 | € 100 | € 100 | € 100 | € 100 | € 100 |
| BV10 | € 200 | € 200 | € 200 | € 200 | € 200 |
| BV11 | RON 20 | RON 20 | RON 20 | RON 20 | RON 20 |
Appendix
Copyright © 2023 International Currency Technologies Corporation
Vol. 1.0 Part Number: SWR8REB0100-R
