Vanity
Version: 12/09/2023
Assembly requires 2 adults.
Important Information
Please read the entire manual thoroughly before starting to assemble and/or use this product. Keep it for further reference.
Safety Warnings
- ❓Important Information: Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
- ?Avoid Scratches: In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
- ?Improve Efficiency: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
- ⚠️Anti-Topple Warning: Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
- ❗Important: It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months - in order to assure stability throughout the lifespan of the product.
- Maintenance and Cleaning: For regular maintenance and cleaning of the product, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
- Installation Caution: Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
Tools and Parts Required
Tools:
A Phillips head screwdriver ?
A hammer or rubber mallet ? (for foot pads)
Parts List:
Note: When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.
| Part Identifier | Code | Quantity | Description |
|---|---|---|---|
| A | CRB1295A | 86 | Cam Lock |
| B | CRA0640A | 86 | Eccentric Rod |
| C | CRC0540A | 21 | Screw |
| D | - | 2 | Metal Bracket |
| E | CRE0418A | 5 | Handle |
| F | - | 10 | Screw |
| G | CRD0312A | 28 | Screw |
| H | CRD3512A | 24 | Screw |
| I | CRD0314A | 4 | Screw |
| J | CRD0312A | 4 | Dowel/Pin |
| K | - | 8 | Foot Pad |
| L | WX0814A | 3 | Runner/Rail |
| M | - | 8 | Layer Pin |
| N | - | 4 | Hinge |
| Power plug | - | 1 | Power Plug |
Assembly Instructions
Step 1
Screw eccentric rod (B) into boards 2, 3, 4, and 5 at first. Knock foot pad (K) into boards 2, 3, 4, and 5 as shown.
Diagram shows eccentric rods (B) being screwed into pre-drilled holes on boards 2, 3, 4, and 5. Foot pads (K) are shown being tapped into the bottom of these boards.
Step 2
Attach board 6, 7, and 10 to board 2. Add cam lock (A) into boards 6, 7, 10 and turn clockwise to tighten as shown.
Diagram shows boards 6, 7, and 10 being attached to board 2 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise to secure the connection.
Step 3
Attach board 4 to boards 6, 7, and 10. Add cam lock (A) into boards 6, 7, 10 and turn clockwise to tighten as shown.
Diagram shows board 4 being attached to the assembly from Step 2, using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 4
Screw eccentric rod (B) into board 4 at first.
Diagram shows eccentric rods (B) being screwed into board 4.
Step 5
Attach board 6, 7, and 10 to board 3. Add cam lock (A) into boards 6, 7, 10 and turn clockwise to tighten as shown.
Diagram shows boards 6, 7, and 10 being attached to board 3 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 6
Attach board 5 to boards 6, 7, and 10. Add cam lock (A) into boards 6, 7, 10 and turn clockwise to tighten as shown.
Diagram shows board 5 being attached to the assembly from Step 5, using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 7
Screw eccentric rod (B) into board 5 at first.
Diagram shows eccentric rods (B) being screwed into board 5.
Step 8
Connect board 4 and 5 to board 9. Add cam lock (A) into board 9 and turn clockwise to tighten as shown.
Diagram shows boards 4 and 5 being connected to board 9 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 9
Fix board 8 to boards 4 and 5 with screw (C) as shown.
Diagram shows board 8 being attached to boards 4 and 5 using screws (C).
Step 10
Fix rail (L) to boards 2, 3, 4, and 5 with screw (G) as shown.
Diagram shows runner/rails (L) being attached to the inner sides of boards 2, 3, 4, and 5 using screws (G). A close-up shows a screw (G) being inserted into the rail (L) and board.
Step 11
Insert back board 11 along available grooves as shown.
Diagram shows back board 11 being slid into the grooves on the rear of the assembled structure.
Step 12
Screw eccentric rod (B) into board 1 at first.
Diagram shows eccentric rods (B) being screwed into board 1.
Step 13
Cover board 1 to the top. Add cam lock (A) into the corresponding holes and turn clockwise to tighten as shown.
Diagram shows board 1 being placed on top of the main structure. Cam locks (A) are inserted and turned 180° clockwise to secure it.
Step 14
Screw eccentric rod (B) into board 1 at first.
Diagram shows eccentric rods (B) being screwed into board 1.
Step 15
Screw eccentric rod (B) into boards 27 and 28 at first.
Diagram shows eccentric rods (B) being screwed into boards 27 and 28.
Step 16
Connect board 28 and 27 to boards 31 and 32. Add cam lock (A) into boards 31, 32 and turn clockwise to tighten as shown.
Diagram shows boards 28 and 27 being connected to boards 31 and 32 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 17
Screw eccentric rod (B) into board 31 at first.
Diagram shows eccentric rods (B) being screwed into board 31.
Step 18
Attach board 29 to board 31. Add cam lock (A) into board 29 and turn clockwise to tighten as shown.
Diagram shows board 29 being attached to board 31 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 19
Screw eccentric rod (B) into board 31 at first.
Diagram shows eccentric rod (B) being screwed into board 31.
Step 20
Attach board 33 to board 31. Add cam lock (A) into board 33 and turn clockwise to tighten as shown.
Diagram shows board 33 being attached to board 31 using cam lock (A). A close-up shows the cam lock being turned 180° clockwise.
Step 21
Fix board 32 to board 33 with screw (C) as shown.
Diagram shows board 32 being attached to board 33 using screw (C).
Step 22
Screw eccentric rod (B) into board 34 at first.
Diagram shows eccentric rods (B) being screwed into board 34.
Step 23
Attach board 34 to board 29. Add cam lock (A) into board 29 and turn clockwise to tighten as shown.
Diagram shows board 34 being attached to board 29 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 24
Insert layer pin (M) into boards 27, 29, and 28 as shown.
Diagram shows layer pins (M) being inserted into the designated holes on boards 27, 29, and 28.
Step 25
Attach the component (likely the mirror/light assembly) to board 1. Add cam lock (A) and turn clockwise to tighten as shown.
Diagram shows the mirror/light assembly (part 34) being attached to board 1 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 26
Insert back board 36 along available grooves as shown.
Diagram shows back boards 36 being slid into the grooves on the rear of the upper structure.
Step 27
Place shelf board 30 as shown.
Diagram shows shelf boards 30 being placed into their designated positions.
Step 28
Insert part (J) into door plates 35 and 39. Fix part (D) to door plates 35 and 39 with screw (G) as shown.
Diagram shows dowels/pins (J) being inserted into door plates 35 and 39. Metal brackets (D) are then attached to these plates using screws (G). A close-up shows screw (G) being used.
Step 29
Screw eccentric rod (B) into board 26 at first. Fix part (D) to board 26 with screw (I) as shown.
Diagram shows eccentric rods (B) being screwed into board 26. Metal brackets (D) are then attached to board 26 using screws (I).
Step 30
Assemble door plates 35 and 39 as shown.
Diagram shows door plates 35 and 39 being positioned, likely to be attached to the main structure.
Step 31
Attach board 26 to boards 27, 29, and 28. Add cam lock (A) into the corresponding holes and turn clockwise to tighten as shown.
Diagram shows board 26 being attached to boards 27, 29, and 28 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 32
Screw eccentric rod (B) into board 12 at first. Fix handle (E) to board 12 with screw (F) as shown.
Diagram shows eccentric rods (B) being screwed into board 12. Handles (E) are then attached to board 12 using screws (F).
Step 33
Attach board 12 to boards 15 and 16. Add cam lock (A) into the corresponding holes and turn clockwise to tighten as shown.
Diagram shows board 12 being attached to boards 15 and 16 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 34
Insert board 19 along available grooves as shown.
Diagram shows board 19 being slid into the grooves of the drawer assembly.
Step 35
Fix board 17 to boards 15 and 16 with screw (C) as shown.
Diagram shows board 17 being attached to boards 15 and 16 using screws (C). A close-up shows screw (C) being used.
Step 36
Fix runner (L) to boards 15 and 16 with screw (G) as shown.
Diagram shows runner/rails (L) being attached to boards 15 and 16 using screws (G). A close-up shows screw (G) being used.
Step 37
Screw eccentric rod (B) into board 13 at first. Fix handle (E) to board 13 with screw (F) as shown.
Diagram shows eccentric rods (B) being screwed into board 13. Handles (E) are then attached to board 13 using screws (F).
Step 38
Attach board 13 to boards 15 and 16. Add cam lock (A) into the corresponding holes and turn clockwise to tighten as shown.
Diagram shows board 13 being attached to boards 15 and 16 using cam locks (A). A close-up shows the cam lock being turned 180° clockwise.
Step 39
Insert board 20 along available grooves as shown.
Diagram shows board 20 being slid into the grooves of the drawer assembly.
Step 40
Fix board 18 to boards 15 and 16 with screw (C) as shown.
Diagram shows board 18 being attached to boards 15 and 16 using screws (C).
Step 41
Fix runner (L) to boards 15 and 16 with screw (G) as shown.
Diagram shows runner/rails (L) being attached to boards 15 and 16 using screws (G). A close-up shows screw (G) being used.
Step 42
Align rails, insert drawers into.
Diagram shows the assembled vanity with drawers being slid into place along the rails.
Step 43
Fix hinge (N) to board 14 with screw (H) as shown. Fix handle (E) with screw (F) as shown.
Diagram shows hinges (N) being attached to door board 14 using screws (H). Handles (E) are then attached to the door using screws (F).
Step 44
Assemble door 14 to boards 2 and 3 by fixing hinge with screw (H) as shown.
Diagram shows door 14 being attached to the main structure (boards 2 and 3) using hinges and screws (H). A close-up shows the hinge attachment.
Step 45
Connect the power cable with light connectors.
Diagram shows the power plug connecting to a cable with two connectors, and the other end of the cable connecting to a power outlet symbol. The light connectors are shown being plugged into the power cable.
Touch lightly to change color, press and hold to adjust the brightness.
Warranty Information
Warranty Claims
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
- Before making a claim, please call for assistance. Provide your purchase order number and details of the problem for replacement parts. Assistance will be arranged within 48 hours. If parts are out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Damage during installation is not covered, but damage during transportation is included.
Scope of Responsibility
- The manufacturer shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- Damage and scratches to the furniture after use are not covered by the warranty.
The Warranty Relates to All Bought in The US and Covers The Following Areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
Changed Your Mind and Need to Return Your Item?
Please follow the retailer's instructions for returns.
Defective Items
If your item is defective in any way, please call for assistance in the first instance.
Damaged Items
If you receive an order with obvious shipping damage from the retailer, refuse the delivery. If delivery is accepted and shipping damage is found, follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Disposing of packaging material or attempting to return merchandise without contacting the fulfiller may jeopardize your chances of making a claim and may result in no credit for the return.
After-Sales Contact
- Email: feedbackstation@163.com
- Phone: (303)800-6387
