Cabinet
Product Overview
This document provides assembly instructions for the Cabinet. It is designed to be assembled by 2 adults. Version: 12/01/2023.
Important Information
Read Manual First
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference. ❓
Assembly Surface
In order to avoid scratching this furniture, it should be assembled on a soft layer, such as a rug. ⚠️
Improve Efficiency
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ?
Anti-Topple Warning
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully. ⚠️
Important Maintenance Notes
It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the lifespan of the product. For regular maintenance and cleaning of the product frame, use a rag dipped in neutral detergent, wipe thoroughly, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break. ?
Safety Warnings
General Safety
This product requires careful assembly. Please follow all instructions to ensure safe and correct usage.
Tipover Warning
Children have died from furniture tipover. To reduce the risk of furniture tipover:
- ALWAYS install tipover restraint provided. ?
- NEVER put a TV on this product. ?❌
- NEVER allow children to stand, climb or hang on drawers, doors, or shelves. ?♂️❌
- NEVER open more than one drawer at a time. ➡️ 1️⃣ ❌
- Place heaviest items in the lowest drawers. ?⬇️
This is a permanent label. Do not remove! ?️
Tools and Parts Required
Tools
- Measuring tape ?
- Screwdriver ?
- Spirit level ?
- Hammer ?
- Drill ?
Parts List
- A x 23(+2): M6.5 x 35 mm
- B x 23(+2): Ø15 x 9.5 mm
- C x 18(+2): Ø8 x 30 mm
- D x 4: Ø35 mm
- E x 24(+2): M3.5 x 14 mm
- F x 2: Ø26 x 11 mm
- G x 1: 1.5 m
- H x 2(+2): 19 x 14 x 8 mm
- J x 4: M3 x 14 mm
- K x 4 sets
Assembly Instructions
Step 1: Screw eccentric rod(A) into board 1
Prepare board 1. Insert three units of eccentric rod (A) with dimensions M6.5 x 35 mm into the designated holes on board 1. Ensure they are screwed in as shown in the diagram.
Visual Aid: Diagram shows board 1 with three 'A' components being screwed in. A magnified view shows the insertion of component 'A' into a hole on board 1. Safety icons: ⚠️, ✔️, ❌.
Parts Used: A x 3 (M6.5 x 35 mm).
Step 2: Attach board 6 to board 1
Attach board 6 to board 1 using wooden dowel (C) and cam lock (B). Add cam lock (B) into board 6 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows board 6 being attached to board 1 with dowels and cam locks. A magnified view shows the 180° rotation of a cam lock (B) to secure the connection.
Parts Used: B x 3 (Ø15 x 9.5 mm), C x 3 (Ø8 x 30 mm).
Step 3: Screw eccentric rod(A) into board 1
Prepare board 1. Insert three units of eccentric rod (A) with dimensions M6.5 x 35 mm into the designated holes on board 1. Ensure they are screwed in as shown in the diagram.
Visual Aid: Diagram shows board 1 with three 'A' components being screwed in. A magnified view shows the insertion of component 'A' into a hole on board 1. Safety icons: ⚠️, ✔️, ❌.
Parts Used: A x 3 (M6.5 x 35 mm).
Step 4: Attach board 5 to board 1
Attach board 5 to board 1 using wooden dowel (C) and cam lock (B). Add cam lock (B) into board 5 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows board 5 being attached to board 1 with dowels and cam locks. A magnified view shows the 180° rotation of a cam lock (B) to secure the connection.
Parts Used: B x 3 (Ø15 x 9.5 mm), C x 2 (Ø8 x 30 mm).
Step 5: Screw eccentric rod(A) into board 2
Prepare board 2. Insert three units of eccentric rod (A) with dimensions M6.5 x 35 mm into the designated holes on board 2. Ensure they are screwed in as shown in the diagram.
Visual Aid: Diagram shows board 2 with three 'A' components being screwed in. A magnified view shows the insertion of component 'A' into a hole on board 2. Safety icons: ⚠️, ✔️, ❌.
Parts Used: A x 3 (M6.5 x 35 mm).
Step 6: Attach board 6 to board 2
Attach board 6 to board 2 using wooden dowel (C) and cam lock (B). Add cam lock (B) into board 6 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows board 6 being attached to board 2 with dowels and cam locks. A magnified view shows the 180° rotation of a cam lock (B) to secure the connection.
Parts Used: B x 3 (Ø15 x 9.5 mm), C x 2 (Ø8 x 30 mm).
Step 7: Screw eccentric rod(A) into board 3
Prepare board 3. Insert seven units of eccentric rod (A) with dimensions M6.5 x 35 mm into the designated holes on board 3. Ensure they are screwed in as shown in the diagram.
Visual Aid: Diagram shows board 3 with seven 'A' components being screwed in. A magnified view shows the insertion of component 'A' into a hole on board 3. Safety icons: ⚠️, ✔️, ❌.
Parts Used: A x 7 (M6.5 x 35 mm).
Step 8: Attach boards to board 3
Attach boards 2, 8, 6, 1, and 5 to board 3 using wooden dowels (C) and cam locks (B). Add cam locks (B) into boards 1, 2, and 8 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows the assembly of multiple boards (1, 2, 5, 6, 8) onto board 3. A magnified view shows the insertion and 180° rotation of a cam lock (B).
Parts Used: B x 4 (Ø15 x 9.5 mm), C x 6 (Ø8 x 30 mm).
Step 9: Insert back board 7
Insert back board 7 along the available grooves as shown in the diagram.
Visual Aid: Diagram shows the main frame of the cabinet with grooves, and back board 7 being slid into place.
Step 10: Screw eccentric rod(A) into board 4
Prepare board 4. Insert seven units of eccentric rod (A) with dimensions M6.5 x 35 mm into the designated holes on board 4. Ensure they are screwed in as shown in the diagram.
Visual Aid: Diagram shows board 4 with seven 'A' components being screwed in. A magnified view shows the insertion of component 'A' into a hole on board 4. Safety icons: ⚠️, ✔️, ❌.
Parts Used: A x 7 (M6.5 x 35 mm).
Step 11: Connect board 4 to the unit
Connect board 4 to boards 2, 8, 6, 1, and 5 using wooden dowels (C) and cam locks (B). Add cam locks (B) into boards 1, 2, and 8 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows board 4 being connected to the partially assembled unit. A magnified view shows the 180° rotation of a cam lock (B).
Parts Used: B x 4 (Ø15 x 9.5 mm), C x 6 (Ø8 x 30 mm).
Step 12: Fix back board 7 and add cam locks
Fix back board 7 to the unit with screw (J) as shown. Add cam lock (B) into boards 5 and 6 and turn clockwise to tighten as shown.
Visual Aid: Diagram shows screw (J) securing the back board. A magnified view shows cam locks (B) being inserted and rotated 180° in boards 5 and 6.
Parts Used: B x 6 (Ø15 x 9.5 mm), J x 4 (M3 x 14 mm).
Step 13: Secure the unit to the wall
Fix the unit to the wall using part (K). Follow the three steps shown: STEP 1 (Drill holes in wall), STEP 2 (Attach bracket to wall), STEP 3 (Secure unit to bracket).
Visual Aid: Diagram shows the cabinet being attached to a brick wall using a drill, bracket, and screws (K). Three steps are illustrated.
Parts Used: K x 4 (M4 x 42 mm).
Step 14: Attach hinges to door 9
Fix hinge (D) to board 9 with screw (E) as shown.
Visual Aid: Diagram shows hinges (D) being attached to door 9 using screws (E). Magnified view shows hinge attachment.
Parts Used: D x 2 (Ø35 mm), E x 4 (M3.5 x 14 mm).
Step 15: Attach hinges to door 10
Fix hinge (D) to board 10 with screw (E) as shown.
Visual Aid: Diagram shows hinges (D) being attached to door 10 using screws (E). Magnified view shows hinge attachment.
Parts Used: D x 2 (Ø35 mm), E x 4 (M3.5 x 14 mm).
Step 16: Assemble door 9 to the cabinet
Assemble door 9 to board 3 by fixing the hinge with screw (E) as shown.
Visual Aid: Diagram shows door 9 being attached to the main cabinet structure (board 3) via hinges and screws (E).
Parts Used: E x 8 (M3.5 x 14 mm).
Step 17: Assemble door 10 to the cabinet
Assemble door 10 to board 4 by fixing the hinge with screw (E) as shown.
Visual Aid: Diagram shows door 10 being attached to the main cabinet structure (board 4) via hinges and screws (E).
Parts Used: E x 8 (M3.5 x 14 mm).
Step 18: Adjust door alignment
If there is misalignment after installation, adjust the screws to the best condition. If doors are still not aligned, please watch the video.
Video Link: ▶️ Watch adjustment video:
Visual Aid: Diagrams show hinge adjustment mechanisms with arrows indicating movement for alignment.
Step 19: Connect lighting and power
Connect the light strip with power supply (G) as shown. Align the arrow and insert.
Visual Aid: Diagram shows the light strip being connected to power supply (G). A magnified view shows aligning an arrow and inserting components.
- Place the wire box (F) into its corresponding position first.
- Tear off the sticker of part (J), stick it to a proper place on board 1. Press to open the clamp, insert the power cord, and press to close.
Parts Used: F x 2 (Ø26 x 11 mm), G x 1 (1.5 m), H x 2 (19 x 14 x 8 mm).
Electrical and Functional Information
Connecting to Wall Switch
Plugs are provided with this product. Recommend to use the plug directly. If you need to link to a wall switch, you can choose to cut off the plug and link the wire. Note: When the plug is cut off, the product is not covered by the warranty. It is recommended that you contact an electrician to install it, or operate under the guidance of a professional.
- Input Voltage: 110V AC
- Output Voltage: 12V DC
- Type: Touch Switch
- Color Temperature: 3000K - 4000K - 6500K
Functions
1. ON/OFF/Switch-color Function
- Short Press: Turn on/off and change the color temperature.
- Press and hold (2-3 seconds): Activate the dimmer function. After the lamp dimmer function is activated, the long press light switch brightness changes from dark to light, and the long press light brightness changes from light to dark.
2. Defogger Button
- First short press: Anti-fog function activates.
- Second short press: Anti-fog function stops. The two operations cycle in turn.
Warranty Information
Warranty Claims
There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
Before making a claim, please call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
The product must be used in accordance with the instructions provided. For health reasons.
For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
Failure to follow the furniture instructions will invalidate the warranty. Attention please.
Does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
After using, the damage and scratches of the furniture are not covered by the warranty.
Warranty Coverage Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns and After-Sales Contact
Return Policy
Changed Your Mind and Need to Return You Item? Please follow the below instructions:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
Defective Items
- If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please call us.
Damaged Items
If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer. In all circumstances please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
After-Sales Contact Information
- Email: feedbackstation@163.com ?
- Phone: (303)800-6387 ?
