Display Cabinet

Important Information

Please read the entire manual before starting to assemble and/or use this product. Follow the manual thoroughly and keep it for further reference.

• Avoid Scratches: To prevent scratching, this furniture should be assembled on a soft layer, such as a rug. ?➡️❌✔️
• Improve Efficiency: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ??
• Anti-Topple Warning: Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase a wall attachment suitable for your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully. ⚠️
• Important Maintenance: It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to ensure stability throughout the product's lifespan. For regular maintenance and cleaning: for the frame, use a rag dipped in neutral detergent, wipe, and then dry with a clean rag. For glass materials, wipe with a rag dampened with glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver or excessive force during installation, as the board can easily break.

Tools Required

Please prepare the following tools:

• Measuring tape
• Pencil
• Spirit level
• Screwdriver (Phillips head)
• Drill
• Hammer

Parts List & Hardware

When installing, please carefully confirm that each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

• Hardware:
• A x 36 (Ø6 x 35 mm)
• B x 44 (Ø15 x 9.5 mm)
• C x 37 (Ø6 x 30 mm)
• D x 20 (Ø3 x 12 mm)
• E x 12 (Ø3 x 16 mm)
• F x 2 (Ø4 x 12 mm)
• G x 14 (Ø4 x 35 mm)
• H x 4 (Ø3 x 14 mm)
• J x 6
• K x 12
• L x 1
• M x 2
• N x 8
• P x 4
• Q x 2
• R x 2
• S x 4 (Ø6 x 70 mm)
• T x 2 (Ø2.5 x 10 mm)
• CL x 2 (300 mm)
• CR x 2 (300 mm)
• DL x 2 (300 mm)
• DR x 2 (300 mm)
• Components (Refer to diagrams for specific parts):
• Part 1
• Part 2
• Part 3
• Part 4
• Part 5
• Part 6
• Part 7
• Part 8
• Part 9
• Part 10
• Part 11
• Part 12
• Part 13
• Part 14
• Part 15
• Part 16
• Part 17
• Part 18 (Doors)
• Part 19
• Part 20
• Part 21
• Part 22
• Part 24
• Part 25
• Part 26
• Special Components:
• J-1
• J-2
• J-3 (Hinge)
• J-4 (Plastic Spacer)
• J-5 (Screw)
• J-6 (Part P)
• J-7 (Screw)

Assembly Steps

1. Step 1: Attach slide rails (CL) and (CR) to boards 24 and 25 respectively using screw (D). The diagram shows screws (D) being inserted into pre-drilled holes on the boards, securing the slide rails.
2. Step 2: Screw eccentric rod (A) into boards 2, 24, 3, and 25. Insert wooden dowel (C) and eccentric rod (S) into boards 24 and 25. Connect board 24 to board 2, and board 25 to board 5. Add cam lock (B) into boards 2, 24, 3, and 25, then turn clockwise to tighten. The diagrams illustrate the insertion of rods and dowels, followed by connecting panels and securing them with cam locks.
3. Step 3: Screw eccentric rod (A) into board 6. Attach board 26 to board 6 using wooden dowel (C), add cam lock (B) into board 26, and turn clockwise to tighten. Attach boards 26, 6, and 5 to boards 2 and 24 using wooden dowel (C), add cam lock (B) into boards 5, 6, and 26, and turn clockwise to tighten. Diagrams show the sequence of attaching these panels and securing them.
4. Step 4: Screw eccentric rod (A) into boards 7 and 16. Attach board 8 to board 7; board 17 to board 16 using wooden dowel (C). Add cam lock (B) into boards 8 and 17, and turn clockwise to tighten. Visuals demonstrate the screw and dowel insertion, followed by panel attachment and cam lock tightening.
5. Step 5: Attach boards 7, 8, 9, 16, and 17 to board 24 using wooden dowel (C). Add cam lock (B) and turn clockwise to tighten. The illustration shows multiple boards being connected to a base panel (24) and secured.
6. Step 6: Connect two boards (20) to plank (21) first. Insert back board (20) along available grooves as shown. The diagram shows two vertical panels (20) being attached to a horizontal panel (21), and then a back panel (20) being slid into place.
7. Step 7: Attach boards 3 and 25 to boards 5, 6, 26, 7, 8, 9, 16, and 17 using wooden dowel (C). Add cam lock (B) and turn clockwise to tighten. This step involves connecting a large top panel (3) and a side panel (25) to the assembled structure.
8. Step 8: Connect two boards (19) to plank (22) first. Insert back board (19) along available grooves as shown. This step appears to be for a different section or a mirrored part of the cabinet, showing back panels being inserted into a frame.
9. Step 9: Fix part (L) to board 1 using screw (H). Attach board 1 to the top using wooden dowel (C), and fix with screw (H). Diagrams show the attachment of a small component (L) and then a larger panel (1) to the top of the structure.
10. Step 10: Insert layer pin (N) into boards 3 and 2. Place shelf board (4) in. Fix board 19 to board 5 with screw (T). Insert buckle (K) into back slots and fix with screw (E). This step details adding shelf supports, shelves, and securing internal components.
11. Step 11: Refer to page 4 for hinge fittings. Fix hinge (J-3) to boards 2 and 3 with screw (J-7). The diagrams show the process of attaching hinges to the cabinet frame and preparing for door attachment.
12. Step 12: Screw eccentric rod (A) into board 10. Connect boards 11, 15, and 12 to board 10, add cam lock (B) and turn clockwise to tighten. Insert bottom board 14 along grooves. Fix board 13 to boards 11, 15, and 12 with screw (G). This step describes the assembly of a drawer unit or base section.
13. Step 13: Fix runner (DL) and (DR) to boards 11 and 12 with screw (D). Align rails and insert drawers. This step shows the attachment of drawer runners to the cabinet frame and the insertion of assembled drawers.
14. Step 14: Install anti-tipping device as shown. This final step illustrates securing the cabinet to the wall using the provided anti-tipping hardware (parts F, M, Q, R). The diagrams show drilling into the wall, attaching brackets, and securing the cabinet.

Warranty

WARRANTY CLAIMS

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call to inquire about your query. Provide your purchase order number and details of the problem for a replacement part. Replacements will be arranged within 48 hours. If the item is out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is.

Scope of Responsibility

• The manufacturer shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
• Damage and scratches after use are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas:

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?

PLEASE FOLLOW THE BELOW INSTRUCTIONS:

• If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

• If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call for assistance in the first instance.

DAMAGED ITEMS

• If you receive an order with obvious shipping damage from the retailer, it is suggested that the delivery be refused. If the delivery has been accepted and shipping damage is subsequently found, please follow the specific instructions advised by the retailer.
• In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive credit for the return.

AFTER-SALES CONTACT

• ✉️ feedbackstation@163.com
• ? (303)800-6387