FUFUGAGA Hall Tree Assembly Instructions
⚠️ IMPORTANT INFORMATION!
Please read the entire manual before starting to assemble and/or use this product. Follow the manual thoroughly and keep it for further reference.
?️ AVOID SCRATCHES! To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
? IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
? ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment if included with this product. Please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
IMPORTANT! It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product. For regular maintenance and cleaning: for the frame, please use a rag dipped in neutral detergent to wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
?️ Tools Required
Please prepare the following tools:
- Screwdriver (not specified type, assumed Phillips head)
- Hammer (for dowels, not explicitly listed but implied)
Parts List
| Part Code | Description | Quantity |
|---|---|---|
| A | 6x35mm Screw (Quickfit screw) | 32 |
| B | 15x10mm Cam lock | 12 |
| C | 6x30mm Wooden dowel | 60 |
| D | 4x40mm Screw | 13 |
| E | 6x60mm Screw | 12 |
| F | M4mm Screw | 1 |
| G | 10x10mm Part | 12 |
| H | 20mm Part | 4 |
| I | 3.5x12mm Screw | 24 |
| J | 4x35mm Screw | 4 |
| K | 15mm Part | 4 |
| L | 20mm Part | 4 |
| M | 3x16mm Screw | 8 |
| N | 3x16mm Part | 28 |
| O | 3x16mm Screw | 28 |
| P | 3x16mm Part | 3 |
| Q | 4x14mm Screw | 8 |
| R | 4x14mm Anti-dumping device | 2 |
| S | Part | 4 |
| T | Part | 2 |
| U | Handle | 2 |
| V | Screw | 4 |
| DL | 300mm Slide runner | 2 |
| DR | 300mm Slide runner | 2 |
| CL | 300mm Slide rail | 2 |
| CR | 300mm Slide rail | 2 |
Assembly Instructions
Step 1
Fix slide rail (CL) and (CR) to the left and right sides of board 15 using screws (I).
Attention: First hole, Attention: second hole.
Step 2
Attach board 16 to board 15 using wooden dowels (C) and screws (D).
Step 3
Fix board 12 to board 16 using screws (D).
Step 4
Insert quickfit screws (A) into board 17. Attach board 20 to board 17 using wooden dowels (C) and screws (J).
Please pay attention to the holes where the accessories are inserted.
Step 5
Attach board 17 to board 15. Insert cam locks (B) into board 15 and turn clockwise to tighten.
Please pay attention to the holes where the accessories are inserted.
Step 6
Attach board 19 to board 16 using screw (A).
Step 7
Attach board 16 to board 19. Insert cam locks (B) into board 16 and turn clockwise to tighten.
Step 8
Insert wooden dowels (C) into the corresponding holes in boards 19, 20, 17, and 12.
Step 9
Fix slide rail (CR) to board 14 using screws (I). Insert quickfit screws (A) into board 14.
Step 10
Attach board 14 to the component. Turn cam locks (B) clockwise to tighten. Insert part (G) into corresponding holes, then fix with screws (E).
Step 11
Connect board 18 to board 14 using wooden dowels (C). Insert part (G) into corresponding holes, then fix with screws (E).
Step 12
Insert wooden dowels (C) into the corresponding holes in boards 19, 20, 17, 12, and 18.
Step 13
Fix slide rail (CL) to board 13 using screws (I). Insert quickfit screws (A) into board 13.
Step 14
Attach board 13 to the component. Turn cam locks (B) clockwise to tighten. Insert part (G) into corresponding holes, then fix with screws (E).
Step 15
Insert quickfit screws (A) and wooden dowels (C) into board 17.
Step 16
Attach board 5 to board 4 using wooden dowels (C) and screws (D).
Step 17
Attach board 6 to board 4. Insert cam locks (B) into board 4 and turn clockwise to tighten. Fix part (L) to board 7 with screws (M).
Step 18
Connect board 7 to board 4 using wooden dowels (C).
Step 19
Connect boards 9 and 7 to board 8 using wooden dowels (C).
Step 20
Insert wooden dowels (C) into the corresponding holes in boards 4 and 6. Slide board 11 into available slots.
Step 21
Insert quickfit screws (A) into board 3.
Step 22
Attach board 3 to the component. Insert cam locks (B) into boards 4, 7, and 9 and turn clockwise to tighten. Insert wooden dowels (C) into the corresponding holes in boards 4 and 6.
Step 23
Slide board 11 into available slots. Insert quickfit screws (A) into board 2.
Step 24
Attach board 2 to the component. Insert cam locks (B) into boards 9, 7, and 4 and turn clockwise to tighten.
Step 25
Slide board 10 into available slots. Insert wooden dowels (C) into boards 2, 5, and 3. Insert quickfit screws (A) into board 1.
Step 26
Attach board 1 to the top of the unit. Insert cam locks (B) into boards 2, 5, and 3 and turn clockwise to tighten.
Step 27
Connect two assembled components. Insert cam locks (B) into boards 2 and 3 and turn clockwise to tighten.
Step 28
Fix the back board using parts (N) and screws (O). Fix the anti-dumping device (R) to board 10 using part (S) and screw (Q). Fix part (P) to boards 9 and 12 using screws (Q).
Step 29
Insert quickfit screws (A) into board 21. Attach boards 23 and 24 to board 21 using wooden dowels (C).
Step 30
Insert cam locks (B) into boards 23 and 24 and turn clockwise to tighten. Slide board 15 into available slots. Attach board 22 to the component using screws (D).
Step 31
Fix handles (U) with screws (V).
Step 32
Fix runners (DL) and (DR) to boards 23 and 24 respectively using screws (I).
Step 33
The assembly of the main unit is now complete. Ensure all parts are securely fastened.
Step 34: Wall Mounting (Anti-Tipple Device)
Secure the item to the wall for safety. Fix the anti-dumping device (R) through part (T) to your wall using part (S) and screws (Q). Ensure the wall type is suitable for the provided hardware or use appropriate wall anchors.
WALL drilling hole 6x30mm.
Step 35: Weight Limits
The unit has specific weight limits for stability and safety: The main structure supports 330 LBS, while individual shelves or compartments may have lower limits (e.g., 22 LBS).
Warranty & Returns
Warranty Claims
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty starts from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, contact customer support. Provide your purchase order number and details of the problem for replacement parts. Arrangements will be made within 48 hours. If a part is out of stock, you will be notified of a shipping date.
- The product must be used in accordance with the provided instructions.
- For health reasons, if the furniture needs to be returned for other reasons, it must be cleaned and dried and returned within 30 days of receipt.
- Warranty Invalidation: Failure to follow furniture instructions will invalidate the warranty. Damage during installation is not covered, but damage during transportation is.
- Scope of Responsibility: The manufacturer shall not bear any responsibility for misuse, user damage, or loss of parts during installation. Damage and scratches after use are not covered by the warranty.
- Warranty Coverage (US): Sheet parts and electrical parts are covered for 1 month from the date of purchase.
Returns
- Changed Your Mind: If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
- Defective Items: If your item is defective, contact customer support first.
- Damaged Items: If you receive an order with obvious shipping damage, refuse the delivery. If accepted and damage is found later, follow the retailer's specific instructions. Always save all packaging material and paperwork for the order. Disposing of packaging or attempting to return merchandise without contacting the fulfillment center may jeopardize your claim and credit.
