Everbilt 15 Inch Undermount Runner Installation Instructions
Item #: 1002 782 619 | Model #: 9236059
For questions, problems, or missing parts, contact Everbilt Customer Service:
8 a.m. - 7 p.m., EST, Monday - Friday | 9 a.m. - 6 p.m., EST, Saturday
1-800-305-1726
HOMEDEPOT.COM
Table of Contents
Safety Information
Please read and understand this manual before installing this product.
⚠️ CAUTION: Always be cautious when using power tools.
Warranty
Subject to the terms of this warranty, the Manufacturer warrants to the original consumer purchaser that the product will be free from defects in material and workmanship. If the product does not comply with this warranty, the Manufacturer will repair or replace the product or, at the Manufacturer's option, refund the purchase price. Repair, replacement, or refund of the original purchase price is your sole remedy under this or any other warranty on the product, whether expressed or implied.
For additional details and questions, please contact Everbilt Customer Service at 1-800-305-1726.
Installation Options
1. Is this the right drawer for my project?
Please check the following points:
- Drawer dimensions need to be met to fit slides.
- Fits 15 in. deep drawers.
- These slides can be installed in frameless and face frame cabinetry. Instructions for both options are provided in this manual.
- The drawer side thickness must be 1/2 in. (13 mm) or 5/8 in. (16 mm).
Face Frame Cabinetry
Diagram showing a face frame cabinet with an inset view of the drawer side thickness.
| Drawer box length | Minimum / maximum inside cabinet depth with metal rear attachment bracket | ||
|---|---|---|---|
| inch | mm | inch | mm |
| 15" | (381 mm) | 15 7/8" - 17 3/4" | (402 - 452 mm) |
Frameless Cabinetry
Diagram showing a frameless cabinet with an inset view of the drawer side thickness.
| Drawer box length | Minimum inside cabinet depth | ||
|---|---|---|---|
| inch | mm | inch | mm |
| 15" | (381 mm) | 15 43/64" | (398 mm) |
Pre-Installation
PLANNING INSTALLATION
Ensure all parts listed in the Package Contents section are included and that you have the listed Tools and Materials Required on hand. If any part is missing or damaged, contact customer service.
TOOLS REQUIRED
- Pencil
- Drill with 3/32" Drill bit for screws
- 1/4" Drill bit for rearhole
- Measuring Tape
- Phillips screwdriver ⊕
PACKAGE CONTENTS
Illustration showing the components of the drawer slide set.
- A: Left Drawer Slide (1)
- B: Right Drawer Slide (1)
- C: Front fixing clips left/right for 5/8" (16 mm) drawer subfront thickness (2)
- D: Optional spacers for 1/2" (13 mm) drawer subfront thickness (2)
- E: Face Frame Bracket (2)
- F: Panhead #6 x 1/2 in. (3,5 x 13 mm) screws (8)
- G: Countersunk #6 x 5/8 in. (3,5 x 16 mm) screws (16)
- H: Countersunk #6 x 3/4 in. (3,5 x 20 mm) screws (4)
- I: Countersunk #6 x 1 in. (3,5 x 25 mm) screws (4)
Dimensions
Please review these diagrams and measure and mark your installation location before you begin the installation procedures.
CABINETRY DIMENSIONS
Diagram illustrating cabinetry dimensions, including inside cabinet width and cabinet opening height.
Measurements:
- 1-15/32" (37 mm)
- 13/16" (21 mm)
DRAWER DIMENSIONS
Diagram illustrating drawer dimensions, including drawer height, drawer side thickness, outside drawer width, and inside drawer width.
Measurements:
- Drawer side thickness: 1/2" (13 mm) or 5/8" (16 mm)
- 1-3/16" (30 mm)
Additional dimension notes:
- Drawer depth: 21 in. (533 mm) outside length of drawer sides, without decorative front, for a four-sided box.
- Drawer slides will not work with 3/4 in. (19 mm) drawer sides. Max. drawer side thickness = 5/8 in. (16 mm).
- Drawer side thickness must be 1/2 in. (13 mm) or 5/8 in. (16 mm).
- Outside drawer width = Inside cabinet width minus 5/8 in. (16 mm) or 3/8 in. (10 mm).
- Inside drawer width = Inside cabinet width minus 1-21/32 in. (42 mm).
- Maximum drawer height = cabinet opening height minus 13/16 in. (20 mm).
- Minimum cabinet opening height = drawer height plus 13/16 in. (20 mm).
- Dimensions in millimeters (inch approximations as noted).
MOUNTING DIMENSIONS
Diagram showing mounting dimensions and drill hole specifications.
Drill hole specifications:
- Ø 1/4" (6 mm) diameter of drill-hole = 1 3/16" (30 mm)
- Depth of drill-hole = 3/8" (10 mm)
Measurements:
- 9/32" (7 mm)
- 7/16" (11 mm)
- 15/32"-19/32" (12-15 mm)
- 1" (26 mm)
Face Frame Installation
1. Preparing the slides
Slide plastic connector from rear bracket into the notch on the left and right drawer slides (A and B) forward, as shown.
Illustration showing how to slide the plastic connector into the drawer slides.
2. Face frame application
Diagram illustrating the face frame application, showing setbacks and gaps from the cabinet front edge.
Measurements:
- Cabinet front edge
- 3/8" (10 mm)
- Setback 3/32" (2 mm)
- Front gap 1/16" (1.5 mm)
Face frame application with overlay decorative front.
Minimum / maximum inside cabinet depth (see below). Inset application increases minimum cabinet depth by thickness of decorative front.
| Drawer box length | Min-Max inside cabinet depth with metal rear attachment bracket | ||
|---|---|---|---|
| inch | mm | inch | mm |
| 15" | (381 mm) | 15 7/8" - 17 3/4" | (402 - 452 mm) |
3. Metal rear attachment set (screw-on)
- Set contains 2 metal rear mount rackets and 2 plastic connectors.
- Non-handed, two-piece design.
- For up to 50 mm (1 15/16") depth adjustment and ± 1,5 mm (1/16") side adjustment.
- Additional adjustment via oblong holes.
- Installation recommended with min. four panhead screws (F).
Diagrams illustrating the metal rear attachment set installation and measurements.
* Center of rear adapter = Width of the face frame - Thickness of the cabinet side panel + 3/8" (10 mm)
Step-by-step illustrations for attaching the slides.
Note: The Face Frame Bracket can also be placed upside down.
Frameless Installation
1. Frameless application
Diagram illustrating the frameless application, showing setbacks and gaps from the cabinet front edge.
Measurements:
- Cabinet front edge
- 1 7/16" (37 mm)
- Min. 5/8" (16 mm)
- 3/8" (10 mm)
- Setback 3/32" (2 mm)
- Front gap 1/16" (1.5 mm)
Frameless application with overlay decorative front.
Minimum cabinet depth (see below). Inset application increases minimum cabinet depth by thickness of decorative front.
| Drawer box length | Min inside cabinet depth | ||
|---|---|---|---|
| inch | mm | inch | mm |
| 15" | (381 mm) | 15 43/64" | (398 mm) |
2. Installing the drawer slides
- Attach the left and right drawer slides (A and B) to the inside of the cabinet using #6 x 5/8 in. screws (G).
- Ensure you leave a 1/16 in. (2 mm) space between the face of the cabinet and the start of the drawer slides.
- Proceed to Drawer Installation and Removal when finished.
Illustration showing the placement of drawer slides (A and B) inside the cabinet with screws (G) and the 2mm gap.
Drawer Installation and Removal
1. Installing the drawer catches
Install each drawer catch (C) into the two front corners of the drawer using #6 x 3/4 in. screws (H) or #6 x 1 in. screws (I). If you need to install the screws at an angle, do not angle the screws more than 30°. If your door subfront is 1/2 in. (13 mm), use the optional spacers (D).
Diagram showing drawer catch dimensions and installation on the drawer bottom.
Drawer Catch Dimensions:
- 26 mm (1-1/32")
- 48 mm (1-7/8")
- 80 mm (3-9/16")
- 10 mm (3/8")
2. Installing the drawer
Insert the drawer onto the glides inside the cabinet and push until the drawer catches click.
Illustrations showing drawer insertion for both frameless and face frame cabinets.
3. Removing the drawer
Gently pull each drawer catch lever and slide the drawer out to remove.
Illustration showing how to disengage the drawer catch lever to remove the drawer.
