Contact Information
For questions, problems, or missing parts, please contact Everbilt Customer Service:
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
Phone: 1-800-305-1726
Website: HOMEDEPOT.COM for the most current information.
Welcome
Everbilt appreciates your trust and confidence. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Everbilt!
Table of Contents
- Safety Information - Page 2
- Warranty - Page 2
- Pre-Installation - Page 3
- Planning Installation - Page 3
- Tools Required - Page 3
- Recommended Number of Hinges Per Door Size - Page 3
- Package Contents - Page 4
- Installation - Page 5
Safety Information
Please read and understand this manual before installing this product.
⚠️ CAUTION: Always be cautious when using power tools.
Warranty
Subject to the terms of this warranty, the Manufacturer warrants to the original consumer purchaser that the product will be free from defects in material and workmanship. If the product does not comply with this warranty, the Manufacturer will repair or replace the product or, at the Manufacturer's option, refund the purchase price. Repair, replacement, or refund of the original purchase price is your sole remedy under this or any other warranty on the product, whether expressed or implied.
For additional details and questions, please contact Everbilt Customer Service at 1-800-305-1726.
Pre-Installation
Planning Installation
Ensure all parts listed in the Package Contents section are included and that you have the listed Tools Required on hand. If any part is missing or damaged, contact customer service.
When planning your installation, ensure the hinge is oriented in its final position as shown. This hinge is intended for inset applications on frameless furniture with the doors positioned inside the front of the cabinet.
Diagram: A side view illustrating the correct orientation of the hinge on a cabinet door and side panel for an inset application. The door is shown positioned inside the front of the cabinet.
When installed successfully, these hinges can open to a maximum of 110°.
Diagram showing angles: 90° and 110°.
Tools Required
- [Screwdriver] #2 Screwdriver
- [Pencil/Scribe] Pencil or Scribe
- [Ruler] Ruler (in. and mm)
- [Drill] Drill
- [Forstner Bit] 35 mm boring bit (Forstner bit)
Pre-Installation (continued)
Package Contents
| Part | Description | Quantity |
|---|---|---|
| A | Hinge | 2 |
| B | Frameless Mounting Plate | 2 |
| C | #5 x 5/8 in. Wood Screw | 4 |
| D | #9 x 5/8 in. Wood Screw | 4 |
Recommended Number of Hinges Per Door Size
Use this diagram to determine how many hinges you will need for your door. If you are hanging a door with a mirror or a door that is wider, you will need additional hinges.
Diagram: Shows door sizes and weights with recommended hinge counts. For example, a 3 ft door weighing 9-13 lbs requires 2 hinges (2x); a 5.2 ft door weighing 14-26 lbs requires 3 hinges (3x); a 6.5 ft door weighing 27-37 lbs requires 4 hinges (4x); and a 7.8 ft door weighing 38-50 lbs requires 5 hinges (5x).
Installation
1. Pre-drilling the installation holes
- Use a pencil and ruler to measure and mark the installation locations as this diagram shows.
- Then use a 1-3/8 in. (35 mm) boring bit to drill the door hole 7/8 in. from the edge. Ensure the door hole is a minimum of 1/2 in. (12.8 mm) deep. Do not drill through the door face.
Diagram for Drilling Hinge Cup: Shows a cross-section of a door edge. It indicates the hole diameter should be Ø1-3/8 in. (35 mm), the depth should be 1/2 in. (13 mm) deep, and the hole should be drilled 7/8 in. (21.5 mm) from the edge of the door.
Diagram: A line drawing of a hinge cup being drilled into a door, showing the 7/8 in. (21.5 mm) and 1-3/8 in. (35 mm) measurements.
2. Installing the hinges to the door
Insert each hinge cup (A) into the pre-drilled hole in the door and secure using two 5/8” wood screws (C) for each hinge (A).
Diagram: Shows a hinge cup (A) being attached to a door using two screws (C).
3a. Installing the mounting plates to the cabinet
Align the mounting plates (B) to the marked position and fasten with two screws (D). See installation diagram on next page.
Diagram: Shows a frameless mounting plate (B) being attached to a cabinet using two screws (D).
Installation (continued)
3b. Diagram for mounting plate screw placement
Diagram: Illustrates the placement of screws for the mounting plate on the cabinet. It shows the 5/8" screw length and a calculation for the total required depth: 1 7/16 in. (or 35 mm) + Thickness of Door.
4. Installing the door to the cabinet
Open the hinges (A) to the fully-extended position.
Connect the hinge arm (A) to the mounting plates (B) and press the hinge arm (X) down until they snap to the plates.
Diagram: Shows the hinge arm (A) being attached to the mounting plates (B) on the cabinet, with the arm being pressed down to snap into place.
5. Adjusting the door
- Height Adjustment: Loosen the top mounting screw (1) to adjust the door up or down.
- Overlay Adjustment: Turn the adjustment screw (2) to adjust the door overlay.
- Depth Adjustment: Turn the eccentric screw (3) to adjust the distance of the doors from the cabinet.
Diagrams: Three diagrams illustrating door adjustments. The first shows adjusting door height using screw (1). The second shows adjusting door overlay using screw (2). The third shows adjusting door depth using screw (3).
Contact Information & Final Notes
For the most up-to-date instructions, please visit HomeDepot.com. Retain this manual for future use.
