SALTO DBolt Touch IC Installation Guide

Additional Information

The SALTO DBolt Touch IC is a new electronic lock designed for multi-family housing and residential markets, offering advanced functionality. It serves as a retrofit solution for upgrading existing deadbolt mechanical locks.

Model: ELECTRONIC INFO. DMOM

Copyright © 2025 Salto Systems, S.L.

Product Dimensions and Components

Key dimensions for the lock mechanism are provided:

• Outside Escutcheon Width: 2-11/16 inches (68 mm)
• Latch/Bolt Center to Door Edge: 3-1/16 inches (77.5 mm)
• Latch/Bolt Center to Door Edge: 2-13/16 inches (72 mm)
• Overall Length (approx.): 6-5/16 inches (160 mm)
• Door Thickness Compatibility: 4 inches or 5-1/2 inches (101.6 or 139.7 mm)
• Total Length (approx.): 11-13/16 inches (300 mm)
• Spindle Length (approx.): 5-13/16 inches (148 mm)

Included hardware and tools:

• TORX 20 screws (x2)
• RESET TOOL (x1)
• TORX 10 screw
• TORX 20 screws (x1, x4)
• PZ2 screws (x3)
• PZ 2 driver bit
• PZ2 x2 driver bit
• Batteries (x4)

Two installation options are supplied: Option A (REF: LDxA...) and Option B (REF: LDxL...).

Compatible with DMM14xx.. series and DMM15xx.. series.

Important Notes Before Installation

Escutcheon Pairing: The inside and outside escutcheons are paired. They will not function correctly if switched with escutcheons from different sets. ⚠️

Door Types:

• WOOD DOORS: RFDTCTW30W01
• STEEL DOORS: RFDTCTS30W01
• (Note: Specific door preparation hardware may not be included.)

Exploded View of Components:

• Outside Assembly
• Door Detector (if applicable)
• Cartridge
• Latch
• Outside Spindle
• Lever Set Screw
• Outside Lever
• Inside Plate
• Fixing Screws
• Inside Cover
• Lever Set Screw
• Fixing Screw
• Hand Selector
• Mounting Screws
• Spindle Screw
• Inside Spindle
• Inside Fixing Plate
• Deadbolt

Key dimensions for door preparation:

• Hole Diameter: Ø2-1/8" (Ø54)
• Door Edge to Latch Center: 4" (101.6 mm)
• Door Thickness Compatibility: 5-1/2" (139.7 mm)

Installation Steps

Step 1: Door and Frame Preparation

Install the latch mechanism into the door. Ensure the strike plate is correctly positioned and installed in the door frame. Use appropriate screws (e.g., PH 2 for latch, TORX 20 for strike plate).

Step 2: Frame Strike Plate Installation

Secure the strike plate to the door frame using the provided screws (e.g., PH 2).

Step 3: Outside Escutcheon Installation

Insert the outside assembly and spindle through the prepared holes in the door. Ensure correct orientation for exterior use.

Step 4: Spindle Length Selection

Refer to the table below to select the correct spindle length ('L') based on your door thickness ('t'):

Step 5: Wire Connections and Inside Assembly Attachment

Connect the wires from the outside assembly to the inside assembly. Then, attach the inside assembly to the door, ensuring all components align correctly. ⚠️

Step 6: Securing Inside Escutcheon

Attach the inside escutcheon to the door. Secure it using the mounting screws. Ensure the inside escutcheon is oriented correctly for the 'Inside Side 1'. ⚠️

Step 7: Hand Selection

Set the hand of the lock mechanism by rotating the spindle as indicated by the 'R' (Right) and 'L' (Left) indicators.

Step 8: Spindle Securing

Insert the spindle and secure it in place with the spindle screw.

Step 9: Wire Connections

Connect the necessary wires between the outside and inside assemblies.

Step 10: Outside Escutcheon Attachment

Attach the outside escutcheon to the door, aligning it with the spindle and securing it with screws (e.g., TX 20).

Step 11: Finalizing Outside Assembly

Ensure the outside escutcheon is properly seated and secured.

Step 12: Securing Outside Escutcheon

Push the outside escutcheon onto the spindle and secure it with the provided screw. A "click!" sound indicates proper engagement.

Step 13: Attaching Cover Plate

Attach the cover plate to the assembly.

Step 14: Inserting Lever

Insert the outside lever and secure it with the lever set screw (TX 10). ⚠️

Step 15: Attaching Battery Cover

Attach the battery cover to the inside assembly.

Step 16: Securing Inside Assembly

Secure the inside assembly to the door using the provided screws (e.g., TORX 10).

Step 17: Door Detector Connection (If Applicable)

For models equipped with a door detector, disconnect the detector cable first. Then, connect the cable as shown. ⚠️

Note: Unplug for models with door detector only!

Step 18: Battery Insertion

Insert the batteries into the inside assembly, observing correct polarity.

Step 19: Handing Set Up

This section details the process for setting the handing (opening direction) of the lock. Rotate the spindle as shown in the diagrams.

Step 20: Handing Set Up (Continued)

Further steps for setting the handing, potentially using a key to rotate the spindle.

Step 21: Reset Procedure

To reset the lock, insert the RESET TOOL into the designated hole and press the button. Observe the LED indicators and listen for the audible beep sequence (e.g., "1 s BEEEEEE EEEEEP") which confirms the reset operation.

Step 22: Final Spindle Rotation

Perform a final rotation of the spindle, possibly with a key, to finalize the handing setup.

Step 23: Attaching Cover Plates

Attach the final cover plates to the lock assembly.

Step 24: Securing Internal Components

Secure internal components with the appropriate screws (e.g., TX 10).

Step 25: Attaching Lever

Attach the outside lever and ensure it is properly secured.

Step 26: Removing Cover

Remove the protective cover from the lock mechanism.

Step 27: Keypad Interaction

Interact with the keypad for operation. A "CLICK HERE" button is indicated for further action or information.

Battery Replacement

Procedure:

1. Remove the inside cover.
2. Remove the old batteries and insert new ones, ensuring correct polarity.
3. Replace the inside cover.

Note: Battery replacement should be completed within 40 seconds (MAX.40") to maintain lock settings.

⚠️

Emergency Opening

In case of emergency, an external power source can be connected using the Type-C connector. This allows for temporary power to operate the lock.

⚠️

Type C Connector

Connect a power bank to the Type-C port.