SALTO DBolt Touch IC Installation Guide

SALTO INSPIRED ACCESS

Product Overview

The SALTO DBolt Touch IC is a new electronic lock designed for multi-family housing and residential markets. It offers a retrofit solution for upgrading existing deadbolt mechanical locks.

Model: ELECTRONIC INFO. DMOM

Specifications and Components

Series: DMM14xx.. series, DMM15xx.. series

Dimensions:

Height: 6-5/16" (160 mm)
Width (Outside): 2-11/16" (68 mm)
Cylinder Projection: 3-1/16" (77.5 mm) / 2-13/16" (72 mm)
Spindle Diameter: Ø2-9/16" (Ø65 mm)
Door Thickness Compatibility: See table below.

Included Components:

Deadbolt mechanism
Latch
Outside Assembly
Inside Assembly
Outside Lever
Inside Lever
Spindles (various lengths)
Mounting screws
Fixing screws
Reset Tool
Strike plate

Required Tools:

Phillips head screwdriver (PH 2)
Torx screwdrivers (TX 10, TX 20)
PZ2 screwdriver

Note on Escutcheons: The inside and outside escutcheons are paired and will not function if switched with different units.

Door Type Compatibility: Suitable for Wood Doors (RFDTCTW30W01) and Steel Doors (RFDTCTS30W01). Some components may not be included for all door types.

Door Thickness and Spindle Length

Door Thickness (t)	Spindle Length (L)
1-9/16" - 1-3/4" (40 - 45 mm)	1-9/16" (40 mm)
1-3/4" - 1-31/32" (45 - 50 mm)	1-31/32" (50 mm)
1-31/32" - 2-3/16" (50 - 55 mm)	2-3/8" (60 mm)
2-3/16" - 2-3/8" (55 - 60 mm)	2-15/16" (75 mm)
2-3/8" - 2-9/16" (60 - 65 mm)	2-9/16" (65 mm)
2-9/16" - 2-3/4" (65 - 70 mm)	2-3/4" (70 mm)
2-3/4" - 2-15/16" (70 - 75 mm)	2-15/16" (75 mm)
2-15/16" - 3-5/32" (75 - 80 mm)	3-5/32" (80 mm)
3-5/32" - 3-11/32" (80 - 85 mm)	3-11/32" (85 mm)

Installation Steps

Step 1: Install Deadbolt

Insert the deadbolt mechanism into the door. Secure it using the screws labeled 'REF: LDxL...' and 'PH 2 | REAL SIZE'.

Step 2: Install Strike Plate

Install the strike plate into the door frame. Secure it using the screws labeled 'REF: LDxA...' and 'PH 2 | REAL SIZE'.

Step 3: Mount Inside Plate

Attach the inside mounting plate to the door using the provided screws. Ensure the hand selector is correctly oriented.

Step 4: Measure Door Thickness

Refer to the table in the 'Specifications and Components' section to select the appropriate spindle length (L) based on the door thickness (t).

Step 5: Connect Spindle and Latch

Insert the spindle through the deadbolt mechanism and connect it to the inside assembly. Ensure the latch is properly engaged.

Step 6: Secure Inside Assembly

Attach the inside cover and secure it with fixing screws. A warning symbol ⚠️ indicates caution is needed.

Step 7: Install Outside Assembly

Carefully insert the outside assembly onto the spindle and align it with the inside assembly. Ensure correct orientation (Inside Side 1). A caution symbol ⚠️ is displayed.

Step 8: Attach Outside Lever

Attach the outside lever to the outside assembly. Rotate it clockwise (R) or counter-clockwise (L) as indicated.

Step 9: Secure Outside Assembly

Insert the fixing screws to secure the outside assembly. Ensure the components align correctly.

Step 10: Connect Internal Wires

Connect the internal wires from the outside assembly to the inside assembly.

Step 11: Secure Inside Assembly Cover

Attach the inside assembly cover and secure it with screws.

Step 12: Finalize Inside Assembly

Complete the attachment of the inside assembly.

Step 13: Engage Mechanism

Ensure the mechanism clicks into place, indicating proper engagement. Listen for a 'click!' sound. ?

Step 14: Attach Outside Cover

Attach the outside cover to the assembly.

Step 15: Test Lever Operation

Rotate the outside lever to test the mechanism. A warning symbol ⚠️ is shown.

Step 16: Insert Battery Pack

Insert the battery pack into the inside assembly. Ensure correct polarity.

Step 17: Secure Inside Assembly

Secure the inside assembly with the appropriate screws.

Step 18: Door Detector Connection

For models with a door detector, disconnect the wire (9a) before proceeding. For other models, connect the wire (9b, 9c).

Note: Unplug for models with door detector only! ?

Step 19: Insert Batteries

Insert the batteries into the battery compartment, observing the correct polarity (+/-). ?

Step 20: Handing Setup - Initial

Begin the handing setup process by rotating the spindle.

Step 21: Handing Setup - Rotation

Continue the handing setup by rotating the spindle.

Step 22: Handing Setup - Reset and Confirmation

Use the reset tool ? to perform a reset. The device will emit beeps (BEEEEEE EEEEEP) indicating the status. This process takes approximately 1 second.

Step 23: Finalize Handing Setup

Complete the handing setup by rotating the spindle.

Step 24: Attach Outside Cover

Attach the outer cover to the assembly, securing it with screws.

Step 25: Secure Outside Cover

Use a TX10 tool to secure the outside cover.

Step 26: Test Lever Operation

Test the operation of the levers.

Step 27: Remove Protective Film

Remove the protective film from the keypad or touch surface.

Step 28: Initial Use

The lock is now ready for initial use. A 'CLICK HERE' prompt is shown, likely for software setup or further instructions.

Battery Replacement

Step 1: Remove the inside cover to access the battery compartment. Observe the green checkmark ✔️ indicating correct battery placement.

Step 2: Replace batteries as needed. The process should take a maximum of 40 seconds (MAX.40"). The indicator shows 'Change/Remplacer/Cambio'. ?

Emergency Opening

In case of emergency, a Type-C connector ? is available for external power. Connect a power bank to the Type-C port to operate the lock. A warning symbol ⚠️ indicates caution is required.

	SALTO DBolt Touch IC Installation Guide Detailed installation guide for the SALTO DBolt Touch IC electronic lock, covering component identification, step-by-step assembly, door thickness adjustments, hand setting, battery replacement, and emergency opening procedures.
	SALTO DBolt Touch Installation Guide: Step-by-Step Instructions Comprehensive installation guide for the SALTO DBolt Touch smart lock, covering all steps from unpacking to final setup, including battery replacement and emergency opening procedures.
	SALTO XS4 Original Ai6xx Installation Guide Comprehensive installation guide for the SALTO XS4 Original Ai6xx series electronic door locks, detailing hardware assembly, handling selection, and important considerations for various door types and configurations.
	SALTO XS4 Original+ and One+ Installation Guide Comprehensive installation guide for SALTO XS4 Original+ and XS4 One+ electronic escutcheon locks, covering hardware installation, battery replacement, and compliance information.
	SALTO XS4 Original Ai6xx Series Electronic Lock Installation Guide Detailed installation guide for SALTO XS4 Original Ai6xx series electronic door locks, covering hardware setup, handing selection, wireless installation, and special functions like AMOK and Key Override. Includes BHMA certification and model specifications.
	SALTO XS4 One Installation Guide Comprehensive installation guide for the SALTO XS4 One electronic lock, covering hardware installation, programming, and model variations. Includes step-by-step instructions and important usage notes.
	SALTO Neo Europe/Swiss Profile Cogwheel Lock Cylinder Installation Guide Comprehensive installation guide for the SALTO Neo Europe and Swiss profile lock cylinders featuring a cogwheel mechanism. Includes step-by-step instructions, battery replacement, and usage recommendations for secure access control systems.
	SALTO LE7Sxx Symmetric Mortise Lock Installation Guide Comprehensive installation guide for the SALTO LE7Sxx symmetric mortise lock, covering preparation, installation, and maintenance. Features include compliance with EN 179 standards for escape routes and fire doors.