Package Contents
- Base unit
- Foot Bath Basin
- Rubber Mat
- Massager attachment
- User Instructions
Technical Data
| Parameter | Specification |
|---|---|
| Voltage | 220-240V |
| Frequency | 50/60Hz |
| Power Consumption | 130W |
| Dimensions (L x W x H) | 50.5 x 40 x 26.5 cm |
| Weight | 3.7 kg |
Control Panel Operation
The control panel allows you to manage the functions of the foot bath.
- Button 1: Heating Function
- Button 2: Vibration Function
- Button 3: Power On/Off
- Indicator 4: Heating Status Indicator
- Indicator 5: Vibration Status Indicator
- Indicator 6: Power Status Indicator
The 'HI' and 'LO' indicators on buttons 1 and 2 control the intensity of heating and vibration. Red indicates high intensity, and green indicates low intensity.
Preparation
Fill the foot bath basin with warm water (or cold water, which will take approximately 30 minutes to heat) to a level that covers the ankles.
Foot Spa Operation
- Place the filled foot bath basin onto the device base.
- Plug in the power cord and press the power button (Button 3). The blue power indicator (Indicator 6) will illuminate.
- Press the heating button (Button 1) and/or the vibration button (Button 2) as desired.
- Heating and Vibration Levels: Both functions offer two intensity levels. The 'HI' indicator being red signifies high temperature/strong vibration. The LED indicator being green signifies low temperature/weak vibration.
- To turn off heating or vibration, press their respective HI/LO indicators until they extinguish.
- When finished, press the power button (Button 3) to turn off all functions. All indicator lights will extinguish.
- Unplug the power cord from the electrical outlet.
- Empty all water from the foot bath basin and wipe the unit dry.
Foot Massage Operation
Remove the foot bath basin (refer to diagram), place the rubber mat on the base, and turn on the unit by pressing the power button.
The control panel operates identically to the foot spa function, allowing selection of heating and vibration.
Important Notes
- The aluminum part of the base becomes very hot during operation. Do not touch or place feet directly on it.
- While the base has a hermetic construction to prevent water ingress and short circuits, exercise caution during daily use. Ensure no water traces remain and wipe the unit dry after each use.
- To move the unit, grasp the base firmly on both sides, being careful of any water in the foot bath basin. Unplug the unit before moving. Once repositioned, plug it back in to resume operation.
- Ensure the electrical connection is properly grounded for safety. If any malfunction is observed, do not attempt to repair the unit yourself. Contact your supplier or an authorized service center.
Safety Measures
- This is professional equipment designed for beauty salons. Operation by qualified cosmetic personnel is recommended to prevent adverse outcomes during treatment.
- Do not disassemble the unit or attempt to use it for purposes other than those specified in these instructions. All servicing and repairs must be performed by an authorized ACTIVESHOP Sp. z o.o. service technician.
- Do not install or operate the device near liquids, in wet areas, or with wet hands to prevent liquid from entering the unit.
- Immediately unplug the unit and contact an authorized ACTIVESHOP Sp. z o.o. service center if:
- (a) liquid has entered the unit,
- (b) the unit emits a strange odor, smoke, or unusual noises,
- (c) the power cord is damaged, or
- (d) the unit has been overturned or its casing is damaged.
- Do not place any objects on the power cords. Do not install the unit where the power cord can be stepped on.
- For safety, always unplug the power cord from the outlet when finished using the device.
- Do not insert any objects into the unit's openings. If a foreign object enters an opening, unplug the cable and contact the distributor or manufacturer.
- Do not place the unit on unstable trolleys, shelves, or vehicles, as it may be damaged if dropped.
- To ensure the unit's intended lifespan, allow a one-minute interval before pressing the power button again (between switching it off and on).
- The power supply must comply with the specifications listed on the unit's nameplate. Failure to do so may result in malfunction, damage, or burning of the unit.
Attention
- In case of damage to the power cord or other malfunctions, contact an authorized service center to avoid any danger.
- This unit may be used by children aged 8 years and older, and by persons with reduced physical or mental capabilities, or lacking experience and knowledge, provided they are supervised or have received instructions for safe use and understand the associated risks.
- The equipment is not intended for children's play. Do not allow children to play with the unit.
- Do not leave the unit unattended when children or persons lacking sufficient knowledge of its use are nearby.
- This electrical appliance is not a toy. Improper use or contact with the electrical unit can pose a risk to health or lead to death; therefore, the unit must be used and stored in a location inaccessible to children.
Disposal of the Unit
Dispose of used electrical appliances, accessories, and packaging at designated recycling centers in accordance with environmental protection regulations. Electrical appliances must not be disposed of in household waste bins. Please observe the specific disposal regulations for this type of equipment.
To protect the environment, as per Directive 2012/19/EU on waste electrical and electronic equipment, used electrical equipment must be collected separately and handed over to collection points for used electrical and electronic equipment. Discarded and old units contain fully recyclable components and should be sent for reprocessing. Therefore, they must be delivered to appropriate collection points or to "ACTIVESHOP" LLC. ♻️
Storage and Transportation
The device must be transported at temperatures between -20 °C and +50 °C, only in its original packaging. Store the device in a well-ventilated room with relative humidity not exceeding 75%. The operating temperature range is +10 °C to +40 °C. During storage and transportation, the device must not be thrown, dropped, or exposed to mechanical shocks or atmospheric influences.
