Product Specifications
Model: Haunt SP1
Type: Suspension Lamp
Bulb Type: E27
Max Wattage: 1 x 60W
Voltage: 220~240V 50/60Hz
Model Numbers: 8021696159256 BIANCO, 8021696159812 LEGNO
Dimensions: Height 2450mm, Diameter Ø 350mm
Certifications: CE, IP20
Installation Guide
Follow these steps for proper installation. Installation must be performed by a qualified electrician.
Step 1: Attach the mounting plate to the ceiling.
Step 2: Connect the electrical wires (Live, Neutral, Earth) to the appropriate terminals.
Step 3: Secure the lamp's canopy to the ceiling.
Step 4: Adjust the suspension cable length to be longer than the chain. Ensure the chain supports the lamp's weight.
Step 5: Prepare the electrical wires by stripping approximately 20 cm of the outer insulation.
Step 6: Strip the ends of the individual wires to approximately 0.5 cm and 1.5 cm respectively.
Step 7: Connect the wires to the terminal block, ensuring correct Live (L), Neutral (N), and Earth connections.
Step 8: Install the light bulb (not included).
Safety Instructions
Please read and follow all safety instructions carefully before installation and use.
- This fitting complies with European safety standards EN 60 598-1.
- Do not dispose of this fitting with normal household waste.
- Installation must be performed by a qualified electrician.
- If the external power cable is damaged, it must be replaced by the manufacturer, distributor, or a qualified electrician.
- Always disconnect the power supply before installation or maintenance.
- The luminaire contains parts that can become very hot.
- Use appropriate screws and wall plugs suitable for the mounting material.
- Ensure all screws are tightened firmly to avoid contact problems.
- This fitting is for indoor use only.
- Do not install on normally flammable surfaces.
- The lamp's weight must be supported by the chain; adjust the electric wire to be longer than the chain.
- Only use bulbs with a wattage not exceeding the specified maximum.
- Maintain the minimum safety distance between the bulb and the illuminated object as indicated by the icon. Failure to do so may cause a fire.
- Use only bulbs marked with the auto-protected symbol. Halogen bulbs get very hot; allow them to cool before replacing.
- If safety glass is cracked or broken, it must be replaced immediately with a compliant spare part.
- The light source (LED) is not replaceable. Do not disassemble the product as diodes can damage eyes. Do not immerse in water. Clean with a damp cloth, avoiding solvents and strong detergents.
- The fitting is equipped with a fuse; replace it if the lamp does not light up.
- Electrical safety class I: requires main insulation and protective conductor (earthing).
- Electrical safety class II: requires main insulation and double or reinforced insulation; earthing is not required.
- Electrical safety class III: requires very low voltage supply (less than 50V); earthing is not required.
- Protection against solid objects:
- - Not protected (31)
- - Protected against dust infiltration (29, 30)
- - Protected against solid objects greater than 1mm (28)
- - Protected against solid objects greater than 2.5mm (27)
- - Protected against solid objects greater than 12mm (26)
- - Protected against solid objects greater than 50mm (25)
- Protection against water:
- - Protected against vertically falling water drops (32)
- - Protected against water drops falling at a maximum angle of 15° (33)
- - Protected against rain (34)
- - Protected against splashing water (35)
- - Protected against water jets (36)
- - Protected against strong water jets (37)
- - Protected against temporary immersion (38)
- - Protected against prolonged immersion (39)
- Do not cover with thermally insulating material.
- Caution: Risk of electric shock.
- Do not stare directly at the light source.
Manufacturer Information
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
Opening Hours: 8:00-12:00 / 13:30-17:00
ELECTRICIAN.LA
