MIBOXER TRI-C1 AC Triac RF+Push Dimmer

1. Feature

• No need to change original electric circuit and install signal cable, low cost price, convenient to construct.
• Dim light through remote and Link code / Unlink code simply.
• Small and exquisite appearance, easy to insert into EU and USA standard wire box.
• Convenient to wire and install.
• Wide application for single color Triac dimmable LED light, traditional filament lamp, and halogen lamp.
• Support 2.4RF remote dimmable, control distance is 30m.
• Support Push dimmable.
• Trailing edge (ELV) phase-cut dimming.
• 0~100% stepless dimming technology.
• Set up minimum brightness via remote quickly.
• Includes switch for temperature and over heat/load protection.
• Support auto transmitting and synchronization for unlimited control distance.
• Output and input with screw connection for simple installation.
• PC shell is fire-resistant.

2. Parameters

Model No.: TRI-C1

Input Voltage: AC100~240V 50/60Hz

Output Voltage: AC100~240V

Output Current: Max 1.36A

Output Power: 150W @110V; 300W @220V

Dim Method: RF wireless dimming, Push dimming

Control Distance: 30m

Working Temperature: -10~40°C

Dimensions: 49mm x 49mm x 25mm

3. Connection Diagram

The diagram shows the wiring for the dimmer. Input: AC100~240V, connected to terminals labeled 'L' and 'N'. Output: Connected to terminals labeled 'L' and 'N' for the load. A push switch is connected to terminals labeled 'L1', 'NC', 'N', and 'L'. The dimmer is designed for Triac dimming of LED lights, traditional filament lamps, and halogen lamps.

Warning: Please ensure all cables are connected correctly before turning on the power supply, otherwise, it will damage the dimmer.

4. Installation Diagram

The diagram illustrates installation within a standard bottom case. It indicates that the push switch requires a bottom case depth of over 50mm.

5. Push Dimming

Short press push switch: Turns the light on or off.

Long press push switch:

• Provides stepless dimming of brightness.
• Long press, release, and long press again to increase or decrease brightness.
• If multiple Triac dimmers are connected to the same auto-reset switch, long press for 20 seconds to synchronize all lights to 100% brightness.

Recommendation: The quantity of dimmers connected to an auto-reset switch should be less than 25, and the length of the auto-reset switch cable should be less than 20m.

6. Link Code

K1 remote Link code:

1. Enter learning code mode. Options:
   • Short press the "SET" button on the dimmer once; the indicator flashes rapidly.
   • Turn the dimmer off for 10 seconds and then turn it back on.
   • Short press the push switch to enter lighting up mode.
2. Press the "SET" button on the remote 3 times within 3 seconds. Matching is confirmed when the light flashes 3 times slowly.

Link code with other remote:

1. Enter learning code mode.
2. Press the "link/unlink" button on the remote (e.g., "?" or "ON") 3 times within 3 seconds. Link code is done if the light flashes 3 times slowly.

7. Unlink Code

Solution 1 (K1 remote): Long press the "SET" button on the dimmer for 3 seconds until the indicator flashes quickly; unlink code is done.

Solution 2 (K1 remote):

1. Enter learning code mode.
2. Press the "SET" button on the remote 5 times within 3 seconds. The light flashes 10 times quickly; unlink code is done.

Unlink code with other remote:

1. Enter learning code mode.
2. Press the "link/unlink" button on the remote (e.g., "?" or "ON") 5 times within 3 seconds. The light flashes 10 times quickly; unlink code is done.

8. Compatible Remote

Compatible remotes (purchased separately) include:

• FUT006
• FUT007
• B1/T1
• B2/T2
• K1
• FUT087
• WL-Box1

9. Set up Min Brightness

This item must be paired with a remote first before setting the minimum brightness.

Set up min brightness with K1:

1. Long press the "SET" button on the remote for 3 seconds until the light flashes once and the dimmer's indicator starts flashing.
2. Short press the "SET" button on the remote to select one of 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Short press any button on the remote (except "OFF") to confirm the setting, or wait 10 seconds for automatic confirmation and exit. The lamp brightness will revert to its previous setting before this procedure.

Set up min brightness with other remote:

1. Long press the "OFF" button on the remote (e.g., "⚫" or "OFF") until the light flashes once and the dimmer's indicator starts flashing.
2. Short press the "OFF" button on the remote (e.g., "⚫" or "OFF") to select one of 10 brightness levels: 3%, 5%, 7%, 9%, 12%, 17%, 22%, 28%, 34%, 40%.
3. Short press any button on the remote except "OFF" to confirm the setting, or wait 10 seconds for automatic confirmation and exit. The lamp brightness will revert to its previous setting before this procedure.

Note: The master "OFF" button can set the minimum brightness for all connected dimmers.

10. Auto Transmitting

The dimmer can transmit signals to another dimmer within a 30m range. The control distance becomes unlimited if a dimmer is installed every 30m.

Attention: All dimmers should be paired with one remote.

11. Attention

• Please turn on power while installing the device.
• Kindly check input voltage before installation.
• Do not disassemble the device if you are not a professional user, as it may cause damage.
• Do not use it near metal or magnetic areas, as it may affect control.
• Dimmer cannot be used in humid areas.

Certifications: CE, UKCA, ROHS. Made in China.