SUNMI T6F0A/T6F0B User Manual and Product Information

Device Overview

This section describes the components and features of the SUNMI T6F0A/T6F0B device.

Front and Side View

• Display ?️: Used for multimedia functions and information display.
• Scanner ?: Supports photo taking and quick 1D/2D code scanning.
• Front/Rear Camera ?: Supports photo taking and quick 1D/2D code scanning.
• NFC (optional) ?: NFC cards can be tapped and read through this.
• Indicator Light ?: Light indicators used for charging, information, scanning, etc.
• Power Button/Fingerprint Recognition (optional) ?:
  • Short Press: Turn on the screen or lock the screen.
  • Long Press: Press for 2-3 seconds to boot up the device when it is off. Press for 2-3 seconds to power off or restart the device when it is on. Press for 11 seconds to force power off the device when it crashes.
• Volume Keys (optional) ?: Adjusting the volume.
• Scan Button ▶️: Short press the button to enable scanning function.
• Function Keys ⚙️: You can set a shortcut function for more convenient use.
• Hand Strap (optional) ?️: For connecting related accessories.
• Type-C ?: Can be used for charging devices and for developer debugging purposes.
• Expansion Interface (optional) ?: For connecting related accessories.
• IC Card Reader ?: Used for reading chip cards. Dual-sided insertion is supported.
• NFC Reader ?: Used for sensing contactless payment cards.
• Magnetic Card Reader ?: Used for swiping bank card magnetic stripes.
• Card Slots: Used for installing PSAM card, Micro SD card, and Nano SIM card.

Back View

• Battery ?: Open the battery cover, install or remove the battery in the direction indicated by the arrow ➡️.
• Back Cover Lock: Slide left and right to switch the battery cover function. Note: The battery cover should be installed on the device, otherwise it will affect normal use.

Safety Information and Warnings ⚠️

General Safety Precautions

• Please insert the AC plug into the AC socket corresponding to the input marked on the power adapter.
• This is a Class B product. In a residential environment, this product may cause radio interference. In this case, it may be necessary for the user to take practical measures to address the interference.
• Do not operate the device in non-safe areas.
• Do not charge the device in dangerous places.
• Use only original batteries.
• Do not replace the battery when explosive gas may be present.
• Battery Replacement: There is a risk of explosion if the battery is replaced by an incorrect type! The old battery shall be given to maintenance personnel for disposal. Do not throw it into fire!
• Please avoid installation or usage during thunderstorms to prevent the risk of being struck by lightning.
• Please disconnect the power immediately once you find any abnormal odors, overheating, or smoke.
• Do not use the device under extreme cold or hot environment, such as conditions near fire or lit cigarettes.
• Do not throw, drop, or bend the device.
• Try to use the device in a clean and dust-free condition to avoid small items falling into the terminal.
• Do not use the device near medical equipment without permission.
• This device is only suitable for safe use in areas with an altitude of 5000m and below.
• Before storing your device for an extended period, please charge the battery to the optimal level to prevent deep discharge. For instance, if you plan to store the device for more than six months, it's recommended to charge it to 50% of its capacity every six months.

Laser Safety

• There is laser light from the scanner, Class 2 laser product. Please do not stare into the beam [laser exit port].

Maintenance

• The terminal is not allowed to be maintained or repaired by itself.

Statements and Disclaimer

Statements

The company is not responsible for the following actions:

• Damage caused by use and maintenance without the conditions described in this guide.
• Damages or problems caused by alternatives or consumables (not the original products or approved products provided by the company). Unauthorized product modifications or changes are not permitted.
• The operating system of this product supports official system updates. If the user flashes a third-party ROM system or modifies the system files using cracking methods, it may cause system instability as well as pose security risks and threats.

Disclaimer

Due to product updates, some details of this document may not match the product; please refer to the actual product. The right to interpret this document belongs to the company. The right to modify this guide without prior notice is reserved.

Pre-installed Software List

To check software details: select "Settings - Applications" and select the corresponding software name. To uninstall software: select "Settings - Applications - Manage Applications - Uninstall" or long-press on the icon and drag it to the "Recycle Bin".

• SUNMI App Store
• Launcher
• Push Service
• User Feedback
• Data Service
• Hardware Manager
• Volume Key Function Customization
• BaseService
• Customization Service (Wallpaper, Boot Animation)
• Developer Guidance (Debugging Assistant)
• User Guide
• Startup Guide
• Remote Assistance
• SUNMI OTA

Regulatory Information

WEEE Compliance ♻️

This symbol means that it is forbidden to dispose of the product with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling.

EU/UK Restrictions

Note: In all EU and UK member states, operation of 5150-5350 MHz is restricted to indoor use only.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

EU Regulatory Conformance (CE)

Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480

Product can be operated in at least one Member State without infringing applicable requirements of the use of radio spectrum. (RED article 10.2).

INFORMATION ABOUT THE SOFTWARE: The description of accessories and components, including software, which allow the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480

ISED Canada Compliance Statements

This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISDE Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, et (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.

RF Exposure Statement (SAR)

This device has been tested and meets EU, FCC and IC RSS-102 applicable limits for radio frequency (RF) exposure. Please visit: www.sunmi.com

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg for body & Head and 4W/kg for extremity averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. The minimum separation distance for body-worn accessories is 10mm, the minimum separation distance for Extremity is 0 mm.

The product SAR limit for Europe is 2.0 W/kg (10g) for head, 4.0 W/kg (10g) for Limb-worn. [Smart POS System, T6F0A/T6F0B] has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification when properly worn on the body (5mm) is 1.25 W/kg, head (0mm) SAR is 0.24 W/kg and Limbs (0mm) SAR is 2.22 W/kg.

Cet équipement a été testé et respecte les limites applicables pour l'exposition aux radiofréquences (RF). Les limites de DAS dépendent de l'utilisation de cet équipement contre la tête ou la main. La limite de DAS IC pour les extrémités est de 4,0 W/kg (10 g) et la limite de DAS pour la tête est de 1,6 W/kg (1 g). La valeur de DAS la plus élevée rapportée selon cette norme lors de la certification du produit en mode tenu à la main est de 1,08 W/kg pour les extrémités (10 mm) et de 0,47 W/kg pour la tête (0 mm).

Technical Specifications

Product Information (Chinese Content Merged)

Network Access Warning (进网警语)

Operating system only supports official upgrades. If the user flashes a non-official system, the user is responsible for security risks and losses (potential risks include: user information theft, automatic message sending, location tracking, etc.).

Device Use Cases: The application scenarios for the device are industries such as express delivery, logistics, retail, and catering. This product serves as a carrier for hardware and system interfaces; corresponding APKs need to be installed according to actual scenarios to achieve the above functions.

• (1) Complies with Article 1, Paragraph 3, Class C of the "Catalog and Technical Requirements for Micro-power Short-range Radio Transmitting Equipment". Built-in ring NFC antenna, magnetic field strength 1.5A/m ≤ magnetic field strength ≤ 7.5A/m. Users can turn this function on and off via "Settings - Connected Devices - Connection Preference Settings - NFC".
• (2) Do not arbitrarily change the usage scenario or conditions, expand the transmission frequency range, increase the transmission power (including adding RF power amplifiers), and do not arbitrarily change the transmitting antenna.
• (3) Do not cause harmful interference to other legal radio stations (stations), nor request protection from harmful interference.
• (4) Must withstand interference from industrial, scientific, and medical (ISM) application equipment that receives radiated radio frequency energy or interference from other legal radio stations (stations).
• (5) If harmful interference is caused to other legal radio stations (stations), stop using it immediately and take measures to eliminate the interference before continuing to use it.
• (6) When using micro-power equipment within electromagnetic protection areas such as airports (within a 5000-meter radius from the airport runway center point), radio astronomical observatories, meteorological radar stations, satellite earth stations (including measurement and control, ranging, receiving, navigation stations), etc., comply with the regulations of electromagnetic environmental protection and relevant industry authorities.
• (7) It is forbidden to use all types of remote control devices within a 5000-meter radius from the airport runway center point.
• (8) The NFC function of this product can work at normal temperatures and is powered by its own adapter and battery.

Disclaimer (免责申明)

Due to product updates, some details of this document may not match the product; please refer to the actual product. The company reserves the right to interpret this document. The right to modify this manual without prior notice is reserved.

Hazardous Substances Identification Table (本产品有毒有害物质名称及含量标识表)

This table identifies the names and content of toxic and harmful substances in the product.

○: Indicates that the content of the toxic and harmful substance in all homogeneous materials of this component is below the limit requirements specified in SJ/T11363-2006.

X: Indicates that the content of the toxic and harmful substance in at least one homogeneous material of this component exceeds the limit requirements specified in SJ/T11363-2006; however, for components marked with "X" in the table, the content exceeds the limit because there is currently no mature alternative technology available in the industry.

Products that reach or exceed their environmental protection use period should be recycled and reused according to the "Measures for the Control of Pollution Control of Electronic Information Products" and should not be discarded at will.

Product Warranty Card (产品保修卡)

Product Name: [Not specified in OCR]

Product Model: T6F0A/T6F0B

Product Serial Number: [Not specified in OCR]

Purchase Date: [Not specified in OCR]

Warranty Period: The company provides a [Number] day warranty service from the date of purchase.

Free warranty is not provided under the following circumstances:

• Products that have been disassembled and repaired without permission.
• Product barcodes, fragile stickers are damaged, and the warranty card is altered or incomplete.
• Faults caused by not operating the equipment according to the instructions.
• Man-made damage caused by water ingress, drops, scratches, or breakage.
• Faults or damage caused by force majeure.
• Outside the warranty period.

Contact Information:

• Company Address: Room 505, No. 388 Song Hu Road, Yang Pu District, Shanghai, China
• Contact Phone: 400-6666-509

EU Representative and Other Information

EU Representative: SUNMI France SAS, 186, avenue Thiers, 69006 Lyon, France