Sunmi T5930 V2 Quick Start Guide and Safety Information

1. Introduction

This document provides essential information for setting up and using your Sunmi T5930 V2 Wireless Data POS System. It covers quick start instructions, safety warnings, and technical specifications.

2. Getting Started: Device Components

Familiarize yourself with the key components of your Sunmi T5930 V2:

• Printer: Used for printing sales slips when the device is powered on.
• Power Button:
  • Short press: Wakes up the screen or locks the screen.
  • Long press (2-3 seconds, powered off): Turns the device on.
  • Long press (2-3 seconds, powered on): Selects power off or reboot options.
  • Long press (11 seconds, system frozen): Initiates an automatic reboot.
• Volume Key: Adjusts the device's audio volume.
• Type-C USB Port: Used for charging the device and for developer debugging.
• Camera: Equipped for payment scanning, supporting both 1D and 2D barcodes.
• Extended Interface: Connects to an optional base accessory (sold separately).
• SIM Card Slot: For cellular connectivity. Note: Ensure the device is powered off before inserting or removing a Nano SIM card to prevent system errors.

3. Printing Instructions

This device supports 58mm thermal paper with specifications of 57±0.5mm x Ø50mm.

Paper Loading Procedure:

1. Open the paper compartment using the designated opening handle. Avoid forcing it to prevent damage to the print head gears. [Illustration: Opening the paper compartment]
2. Insert the thermal paper roll correctly into the compartment, following the indicated direction. Pull a small portion of the paper out beyond the cutter. [Illustration: Inserting paper correctly]
3. Close the paper compartment lid to complete the installation. [Illustration: Closing the lid]

Note: If printed output is blank, verify that the paper roll is installed in the correct orientation.

4. Safety and Warnings

4.1 General Safety Warnings

• Connect the AC plug only to the AC socket that corresponds to the input marking on the power adapter.
• This is a Class A product. In a living environment, it may cause radio interference, requiring the user to take measures against such interference.
• Use only the battery supplied with the device.
• Do not replace the battery where there is a risk of explosion.
• Do not charge the battery in hazardous locations.
• The paper cutter is sharp; do not touch it.

4.2 Significant Safety Instructions

• Avoid installation or use during lightning storms to prevent the risk of electric shock.
• Immediately disconnect power if you notice any abnormal odor, excessive heat, or smoke.

4.3 Suggestions for Use

• Do not use the device near water or moisture.
• Avoid using the device in extreme cold or hot environments, such as near open flames or lit cigarettes.
• Do not drop, throw, or bend the device.
• Use the device in a clean, dust-free environment to prevent small objects from entering.
• Do not use the device near medical equipment without explicit permission.

4.4 Statements and Disclaimer

The company is not responsible for damages caused by:

• Use and maintenance not in accordance with the instructions in this guide.
• Damage or issues caused by optional items or consumables not provided or approved by the company.
• Unauthorized modifications or alterations to the product.

The product's operating system supports official updates. Modifying the system with third-party ROMs or cracking may lead to instability, security risks, and threats.

Due to product upgrades, some details in this document may differ from the actual product. The actual product governs. The company reserves the right to interpret this document and to modify its specifications without prior notice.

4.5 Product Safety Warnings

• General: Use responsibly. Read all safety information before use. The declared operating ambient temperature range is -15°C to 55°C.
• Battery Safety: Charge batteries only at ambient temperatures between 0°C and 40°C. Caution: Risk of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer instructions.
• Adapter Safety: When charging, place the device in an environment with normal room temperature and good ventilation. Recommended charging temperature range is 0°C to 40°C. Use only for altitudes below 2km.
• Wi-Fi Safety: Turn off Wi-Fi in areas where its use is prohibited or may cause interference or danger (e.g., on airplanes).

5. Compliance and Technical Information

5.1 Declaration of Conformity

Shanghai Sunmi Technology Co., Ltd. declares that the Wireless data POS System (Model No.: T5930) complies with the essential requirements and provisions of RED 2014/53/EU.

Caution: For operation within the European Community, the device is restricted to indoor use when using frequencies in the 5150MHz-5250MHz range to minimize interference potential.

5.2 FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including that which may cause undesired operation.

FCC ID: 2AH25V2

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, providing reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to try measures like reorienting the antenna, increasing separation, or consulting a dealer/technician.

5.3 RF Exposure Information (SAR)

This wireless data POS System meets government requirements for radio wave exposure. The guidelines are based on standards developed by independent scientific organizations. The SAR limit in the USA (FCC) is 1.6W/kg averaged over one gram of tissue.

For body-worn operations, a minimum separation distance of 1.0 cm (10mm) or 0.5 cm (5mm) must be maintained between the user's body and the device, depending on the specific test configuration. Use accessories that maintain these separation distances and avoid those with metallic components.

The highest reported SAR values during product certification were:

• 1.042 W/kg (10g SAR, test distance: 0mm, limit 4W/kg)
• 0.983 W/kg (1g SAR, test distance: 5mm, limit 1.6W/kg)

5.4 Technical Features and Characteristics

The following tables detail the device's supported frequency bands and their maximum transmitted power:

Cellular Bands:

Wireless Bands:

5.5 Toxic and Hazardous Substances Identification

The table below identifies the presence of toxic and hazardous substances in the product's components, in accordance with SJ/T 11363-2006.

Legend:

• '○': Content is below the specified limit.
• 'X': Content exceeds the specified limit, often due to the absence of mature alternative technologies.

Products reaching or exceeding their environmental protection service life should be recycled and reused according to regulations, not discarded randomly.

6. Warranty Information

Product Name: Wireless data POS System

Product Model: T5930

Product Serial Number: [Placeholder for Serial Number]

Purchase Date: [Placeholder for Purchase Date]

Warranty Period: The company provides [Number] days of warranty service from the date of purchase.

Exclusions from Free Warranty:

• Products that have been disassembled or repaired without authorization.
• Products with damaged or altered serial number labels or warranty cards.
• Malfunctions caused by failure to operate the device according to the instructions.
• Man-made damage, such as water ingress, drops, scratches, or breakage.
• Malfunctions or damage caused by force majeure events.
• Issues arising after the warranty period has expired.

Contact Information:

• Company Address: Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China
• Contact Phone: [Placeholder for Phone Number]

7. Manufacturer Information

Manufacturer: Shanghai Sunmi Technology Co., Ltd.

Address: Room 505, KIC Plaza, No.388 Song Hu Road, Yang Pu District, Shanghai, China

Explosion Proof Mark: Ex ic IIB T6 Gc

Explosion Proof Certificate Number: CCRI 19.2121