OttLite Ultimate LED 3-in-1 Creative Station with Magnifier

Congratulations and Product Registration

Congratulations on your purchase of the OttLite Ultimate LED 3-in-1 Creative Station with Magnifier, featuring advanced natural lighting technology. Please complete the enclosed Product Registration Form and return it by mail, or register online at www.OttLite.com/warranty.

Safety Warnings

WARNING: To prevent electric shock, ensure the lamp is unplugged until all assembly steps are complete.

CAUTION: TIP HAZARD. DO NOT move the shade or accessories outside the shaded area indicated in Figure 1. The shade and accessories must remain within this area and align forward with the base.

• Turn off/unplug and wait for the shade (K) to cool before handling.
• The LED light panel (P) may become hot after prolonged use; avoid direct contact.
• Only use extension cords where the plug can be fully inserted.
• Do not alter the plug.
• The lamp head is not user-replaceable.
• For indoor use only.
• Use common sense and caution with any electrical product.

CAUTION: If the external flexible cable or cord of this luminaire is damaged, it must be exclusively replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.

CAUTION: The light source of this luminaire is not replaceable. When the light source reaches its end of life, the entire luminaire shall be replaced.

Indoor Use Only: Never leave the magnifier lens unattended in direct sunlight or where light can shine through it, as this can pose a fire risk.

Lamp Assembly

This lamp can be configured as a Floor Lamp, Table Lamp, or Clamp-On Lamp.

Floor Use

1. Place the base (A) on a flat, steady surface (the floor).
2. Remove bolt (E), flat washer (D), and wrench (F) from the plastic bag.
3. Firmly insert the dowel (C) of the pole (B) into the hole in the base (A).
4. Insert the bolt (E) through the flat washer (D) and into the recessed hole at the bottom of the base (A).
5. Use the enclosed wrench (F) to tighten the bolt (E) securely by turning clockwise.
6. Assemble the shade assembly (H) by inserting dowel (G) into the hole of the upper pole (B). Ensure the indent on the front of dowel (G) aligns with the inner tab for a secure fit. The shade assembly (H) should be flush with the upper pole (B) and free to rotate. (See Figure 2 for dowel indent detail).

Table Use

1. Place the base (A) on a flat, steady surface (the table).
2. Remove bolt (E), flat washer (D), and wrench (F) from the plastic bag.
3. Assemble the shade assembly (H) by inserting dowel (G) into the hole of the base (A).
4. Insert the bolt (E) through the flat washer (D) and into the recessed hole at the bottom of the base (A).
5. Use the enclosed wrench (F) to tighten the bolt (E) securely by turning clockwise.

Clamp-On Use

1. Attach the clamp (J) to a table, shelf, or other strong, solid surface. Secure the clamp (J) by turning screw (W) clockwise by hand until it is tightly fastened.
2. Assemble the shade assembly (H) by inserting dowel (G) into the hole of the clamp (J). The shade assembly (H) should be flush with the clamp (J) and free to rotate.

Operation

1. To position the shade (K): Turn wingnut (M, N) counter-clockwise to loosen. Adjust the shade (K) to the desired position and tighten the wingnut (M, N) by turning clockwise. Do not move the arm (O) with wingnuts tightened, and do not overtighten them.
2. The shade (K) can be rotated side-to-side at its neck. Do not attempt to rotate the shade 360 degrees.
3. This lamp includes an LED lighted magnifier (Q) and clip (R). Adjust the position of the magnifier and clip by grasping the flexible neck (T, U) and repositioning.
4. To prevent tipping when using the Table or Floor mount, ensure the weight of the shade assembly, LED lighted magnifier, and clip is positioned over the long part of the base. (See Figure 1).
5. Plug the lamp into a standard 120V outlet.
6. Turn the lamp ON & OFF using the power switch (L). The lamp offers 3 levels of brightness.
   • To turn the lamp ON to the 1st brightness setting, touch the switch once.
   • For the 2nd brightness setting, touch the switch twice.
   • For the 3rd brightness setting, touch the switch three times.
   • To turn the lamp OFF, touch the switch four times.
7. Turn the LED lighted magnifier ON or OFF by sliding switch (S) UP or DOWN.
8. The auxiliary outlet (V) located in the base of the shade assembly is available for use with a two-prong, polarized 120V tool of less than 700 watts. (See Figure 3). The outlet (V) is not controlled by the lamp switch and can be used when the lamp is turned OFF.

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Any change or modification to the product not expressly recognized by OttLite voids OttLite's responsibility for proper function of the product.

Also complies with CAN ICES-005 (B)/ NMB-005 (B).

Diagram Descriptions

Figure 1: Illustrates the base (A) and the designated "Usable area for shade" (shaded area) which is crucial for maintaining stability and preventing tipping, especially when the lamp is configured as a floor or table lamp.

Figure 2: Details the connection point for the shade assembly (H) to the pole (B) or clamp (J). It highlights the importance of aligning the indent on the dowel (G) with the inner tab for a secure and rotatable connection.

Figure 3: Shows the location of the auxiliary outlet (V) on the base of the shade assembly, indicating its availability for powering other 120V devices.