OttLite EasyView LED Craft Floor Lamp

Congratulations

You've purchased the finest in natural lighting technology with your new OttLite® product.

Product Registration

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty.

Assembly Instructions

Warning: To prevent electric shock, make sure the lamp is not plugged in until all assembly steps are complete.

Parts Identification (based on diagram):

• A: Base
• B: Lower Pole
• C: Upper Pole
• D: Flex-neck/Arm
• E: Shade
• F: LED Light Panel
• G: Connector
• H, J: Washers
• K: Bolt
• L: Wrench
• M: Magnifier Bolt
• N: Wing Nut
• P: Clip
• Q: Magnifier Attachment
• R: Power Switch
• S: A/C Adapter Input
• T: A/C Adapter

1. Unpack all lamp parts and lay out with the Base (A) lying flat on a steady surface.
2. Remove wrench (L), bolt (K) and washers (J, H) from the plastic bag included in the box containing the base.
3. Firmly insert the pole (B) into the hole located in the base (A) with connection (G) facing backwards.
4. Insert bolt (K) through the lock washer (J), then through flat washer (H), and finally into the recessed hole in the bottom of the base (A).
5. Use the enclosed wrench (L) to tighten the bolt (K) securely, turning clockwise until tight.
6. Thread upper pole (C) to lower pole (B) by hand turning clockwise until tight.
7. To ease assembly, straighten flex-neck (D) so that neck and shade (E) are in a straight line.
8. Thread arm (D) into upper pole (C) by hand turning clockwise until tight.
9. Connect the A/C adapter input (S) into connector (G) located in the rear-bottom of pole (B).

Magnifier Attachment

1. Unscrew the wing nut (N) from the bolt (M) by turning counter-clockwise and remove from the clip (P).
2. Decide at what height you would like the magnifier attachment (Q) to be placed. Attach the clip (P) to the round stem (C) at the desired height.
3. To secure the magnifier attachment to the lamp, put the bolt (M) through the hole on the clip (P). Place the wing nut (N) on the tip of the bolt and turn wing nut (N) clockwise to tighten.

CAUTION: RISK OF FIRE! NEVER PLACE THE MAGNIFIER ATTACHMENT (Q) UNDER DIRECT SUNLIGHT.

Operation

1. Plug the A/C Adapter (T) into a standard household 120V AC outlet. Note: Only use with supplied A/C adapter to avoid damage or fire.
2. Turn the lamp ON & OFF by using power switch (R). Note: This lamp provides 3 levels of brightness.
3. To power LED settings, slightly touch the switch (R) to achieve the following:
   • Turn lamp "ON" to 1st brightness setting: touch the switch "once"
   • For 2nd brightness setting: touch the switch "two-times"
   • For 3rd brightness setting: touch the switch "three-times"
   • To turn lamp "OFF": touch the switch "four-times"
4. To position the shade simply bend the flex-neck (D) as needed to point the light. To avoid damaging the lamp, DO NOT force the flex-neck into a sharp bend.

Safety Warnings

• Turn off/unplug and WAIT UNTIL SHADE (E) IS COOL before handling.
• The LED light panel (F) might get hot after several hours of continuous use, DO NOT place your hands directly on LED light panel.
• Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
• Do not alter the plug.
• The lamp head included with this unit cannot be replaced by the consumer.
• INDOOR USE ONLY
• Note: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
• CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
• CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

FCC Part 15 Compliance

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) this device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.

CAN ICES-005 (B)/ NMB-005 (B)

AC/DC Adapter Specifications

• Input: AC 100-240V, 50/60 Hz, 0.6A
• Output: 18V DC, 0.65A with a Male DC Plug

Accessories: Wrench