OttLite 2-in-1 LED Magnifier Floor and Table Light

Congratulations!

You've purchased the finest in natural lighting technology with your new OttLite® product.

Product Registration

Please complete the enclosed product registration form and return it today by mail, or register online by going to: OttLite.com/warranty.

Important Safety Information

[WARNING!] To prevent electric shock, make sure the lamp is not plugged in until all assembly steps are complete.

Your 2-in-1 LED Magnifier Lamp can be used as a Floor Lamp and a Table Lamp.

[CAUTION!] [TIP HAZARD] Do not move shade or accessories outside of the shaded area as shown in Figure 1. Shade and accessories must be kept within the shaded area and must align in the same forward-facing direction as the base.

Figure 1 Description

Figure 1 illustrates the 'Usable area for shade and accessory'. It indicates a specific zone where the shade and accessories must be placed to ensure stability and proper function. The text also notes: 'Zone sécuritaire pour l'abat-jour et les accessoires' and 'Area útil para la pantalla y accesorios'.

Figure 2 Description

Figure 2 points out a specific 'INDENT' or 'L'ENCOCHE' or 'MUESCA' detail, which is crucial for correctly aligning the shade and gooseneck assembly with the pole or base.

[CAUTION!] Risk of fire! Never place magnifier in direct sunlight.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

Lamp Assembly - Floor Use

1. Unpack all lamp parts and lay out with the base [A] lying flat on a steady surface.
2. Remove [bolt L], [lock washer K], [flat washer J] and [wrench M] from plastic bag marked "Floor Lamp".
3. To start floor lamp assembly, insert [upper pole C] into [bottom pole B] and thread lightly until tightened.
4. Firmly insert the stem (or bottom) of assembled poles [B-C] into the hole located in the [base A]. [NOTE:] Already assembled [adapter D] in [upper pole C] has an [arrow symbol] on its surface plate. Place the [arrow symbol] in the forward-facing position of [base A] and make sure the [arrow symbol] remains forward-facing until the completion of assembly.
5. Insert [bolt L] through [lock washer K], then through [flat washer J] and finally into the recessed hole in the bottom of the [base A] as shown in the diagram.
6. Use the enclosed [wrench M] to tighten [bolt L] securely, turning [clockwise-arrow] until tight.
7. Assemble [shade and gooseneck assembly F] by inserting [dowel E] into [adapter D] located on [upper pole C] to complete floor lamp assembly. [IMPORTANT:] To lock [dowel E] into [upper pole C], make sure the [indentation-notch] located on the back of [dowel E] is "coupled" with the inner pole [tab]. The [shade and gooseneck assembly F] should be flush with the [upper pole] and free to rotate. The [dowel E] indentation can be easily seen in Figure 2.
8. Connect the [input jack S] with the provided [adaptor R]. Plug the cord into a standard 120Vac outlet.

Lamp Assembly - Table Use

1. Unpack all lamp parts and lay out with the base [A] lying flat on a steady surface.
2. Remove [bolt P], [lock washer O], [flat washer N] and [wrench M] from plastic bag marked "Table Lamp".
3. Insert [base adapter Q] into [base A]. [NOTE:] Adapter [Q] has an [arrow symbol] on its surface. Place the [arrow symbol] in the forward-facing position of [base A]. Insert [adapter Q] with the [arrow symbol] in the forward-facing position until fully seated.
4. With power cord aligned toward the rear of [base A], insert [dowel E] into the top of the [base A]. [IMPORTANT:] To lock [dowel E] into [base A], make sure the [indentation-notch] located on the back of [dowel E] is "coupled" with the inner adapter [tab]. The [shade and gooseneck assembly F] should be flush with the [upper pole] and free to rotate.
5. Insert [bolt P] through [lock washer O] then [washer N] and finally into the recessed hole in the bottom of the [base A] as shown in the diagram.
6. Use the enclosed [wrench M] to tighten [bolt P] securely, turning [clockwise-arrow] until tight.
7. Connect the [input jack S] with the provided [adaptor R]. Plug the cord into a standard 120Vac outlet.

Operation

1. Turn the lamp [ON/OFF] by pressing and depressing [switch H] located on the front of [shade G].
2. Position [shade G] by grasping the [handle] located in front of the shade.
3. [Shade G] can be rotated side to side about its neck. DO NOT attempt to rotate shade all the way around (360 degrees).
4. Keep direct sunlight away from magnifier.
5. INDOOR USE ONLY.

[NOTE:] The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

FCC Part 15 Compliance

[NOTE:] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

[CAUTION:] Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.

CAN ICES-005 (B) / NMB-005 (B)

AC/DC Adapter

Input: AC 120V, 60 Hz

Output: 13.5V DC, 330mA with female DC plug