Yaheetech 592275 Instruction Manual

Introduction

Thank you for purchasing a Yaheetech product. Please read this instruction manual carefully before attempting to assemble or use your new item. This guide provides essential information for a smooth and safe assembly process.

Important Safety Information:

• Assembly should ideally be performed by two adults.
• Ensure you have a clear, spacious area for assembly.
• Keep small parts and packaging materials away from children to prevent choking hazards.
• Do not overtighten screws, as this may damage the material.
• Periodically check all fittings and re-tighten as necessary.

Parts List

Before you begin, please identify and count all parts to ensure nothing is missing or damaged. If any parts are missing or damaged, please contact customer support.

Hardware:

• A: Cam Bolts (x16) - Metal bolts with a threaded end and a flat head.
• B: Cam Locks (x16) - Small cylindrical metal pieces with an arrow indicator.
• C: Wooden Dowels (x20) - Small cylindrical wooden pegs.
• D: Screws (x12) - Standard wood screws, approximately 30mm long.
• E: Allen Key (x1) - L-shaped metal tool for tightening certain bolts.
• F: Back Panel Nails (x24) - Small, thin nails for securing the back panel.

Panels:

• G: Left Side Panel (x1) - Tall rectangular panel with pre-drilled holes.
• H: Right Side Panel (x1) - Tall rectangular panel with pre-drilled holes, mirror image of Panel G.
• I: Top Panel (x1) - Rectangular panel, likely with finished edges.
• J: Bottom Panel (x1) - Rectangular panel, similar to Top Panel.
• K: Shelf Panel (x2) - Rectangular panels for internal shelving.
• L: Back Panel (x1) - Thin, foldable panel, often made of fiberboard.

Assembly Instructions

Follow these steps carefully to assemble your Yaheetech 592275 unit.

Step 1: Prepare Side Panels

Insert Cam Bolts (A) into the designated larger holes on the inner faces of the Left Side Panel (G) and Right Side Panel (H). Screw them in until snug. Insert Wooden Dowels (C) into the smaller pre-drilled holes on the same faces.

[Textual description of diagram: Cam bolts and dowels are shown being inserted into pre-drilled holes on the inner surfaces of two tall, rectangular side panels.]

Step 2: Attach Bottom Panel

Align the Bottom Panel (J) with the corresponding holes and dowels on the lower edges of the Left Side Panel (G) and Right Side Panel (H). Push the panels together firmly. Insert Cam Locks (B) into the large holes on the underside of the Bottom Panel (J), ensuring the arrow on the cam lock points towards the cam bolt head. Turn the Cam Locks clockwise using a screwdriver to secure the panels.

[Textual description of diagram: The bottom panel is shown connecting to the base of the two side panels. Cam locks are being inserted into the bottom panel and turned to secure the connection.]

Step 3: Install Shelves

Insert Wooden Dowels (C) into the designated holes on the inner faces of the side panels (G and H) at the desired shelf heights. Place the Shelf Panels (K) onto these dowels. For fixed shelves, insert Cam Bolts (A) into the side panels and Cam Locks (B) into the underside of the shelves, then secure by turning the cam locks.

[Textual description of diagram: Shelves are shown being slid into place, supported by dowels, and then secured with cam lock mechanisms.]

Step 4: Attach Top Panel

Repeat the process from Step 2 to attach the Top Panel (I) to the upper edges of the Left Side Panel (G) and Right Side Panel (H). Ensure all connections are secure.

[Textual description of diagram: The top panel is shown being attached to the upper edges of the side panels, similar to how the bottom panel was attached.]

Step 5: Secure Back Panel

Carefully turn the unit onto its front. Align the Back Panel (L) with the rear edges of the assembled frame. Ensure the unit is square before proceeding. Use the Back Panel Nails (F) to secure the Back Panel (L) to the rear edges of the side, top, and bottom panels. Hammer the nails in at regular intervals.

[Textual description of diagram: The unit is lying face down. A thin back panel is aligned with the rear edges. Small nails are being hammered along the perimeter to attach the back panel, with an emphasis on maintaining a square frame.]

Step 6: Final Touches

If your unit includes adjustable feet or decorative caps, install them now. Carefully stand the unit upright in its desired location.

[Textual description of diagram: The fully assembled unit is shown standing upright. Optional feet are being adjusted or decorative caps are being fitted.]

Care and Maintenance

To keep your Yaheetech product looking its best:

• Clean with a soft, damp cloth. Avoid abrasive cleaners.
• Wipe up spills immediately.
• Check and tighten all fittings periodically.

Troubleshooting

Issue: Unit is wobbly.
Solution: Ensure all cam locks and screws are tightened. Check if the unit is on a level surface. Adjust feet if applicable.

Issue: Parts do not align.
Solution: Double-check that you are using the correct parts for the step and that they are oriented correctly. Loosen previous connections slightly if needed to allow for adjustment.