Introduction
Congratulations on your purchase of the OttLite® Creative Curves LED Desk Lamp, featuring natural lighting technology.
Product Registration
Please complete the enclosed Product Registration Form and return it by mail, or register online at OttLite.com/warranty.
Assembly and Operation
NOTE: THIS UNIT IS FULLY ASSEMBLED
- Remove the lamp from its packaging, placing the lamp body base (A) flat on a steady surface.
- Connect the AC Adapter input (H) into connector (F) located at the rear-bottom of the lamp.
- Plug the A/C adapter (J) into a standard household 120V AC outlet. NOTE: Only use the supplied AC adapter to avoid damage or fire.
- Turn the lamp ON & OFF using the power switch (B), located on the front lower-side of the base (A). This is a "touch" switch that controls the dimmer function for 4 levels of brightness.
- To adjust LED settings, slightly touch the switch:
- Touch once: Turn lamp "ON" to the 1st brightness setting.
- Touch twice: Set to 2nd brightness.
- Touch three times: Set to 3rd brightness.
- Touch four times: Set to 4th brightness.
- Touch five times: Turn lamp "OFF".
- To position the shade, simply bend the flex-neck (E) as needed to point the light. Please hold the lamp base (A) while adjusting the lamp. Take care not to overextend the lamp to avoid unbalancing it and causing damage.
Enjoy your OttLite® Creative Curves LED Desk Lamp!
Safety Warnings
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
- Turn the lamp off and WAIT UNTIL LAMP HEAD (C) and ADAPTER (J) ARE COOL before handling.
- The LED panel (D) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
- Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
Important Safety Information & Compliance
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) this device may not cause harmful interference, and
- (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-005 (B) / NMB-005
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.8A
Output: 13V DC, 1.2A with a Male DC Plug
THIS LAMP CONTAINS a 5V-2.1A USB output port (G) located on the base of the lamp. USB port can charge such items as tablets, cellular phones, etc.