Product Registration
Please complete the enclosed Product Registration Form and return it today by mail.
Battery Replacement
This lamp uses a CR2032 battery. For battery replacement, refer to the description of Diagram 3. The battery compartment is located on the backside of the lamp body (D).
Battery Safety:
This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.
Safety Warning: To Reduce the Risk of Fire, Electric Shock, or Injury to Persons
- Turn lamp off and WAIT UNTIL LAMP HEAD (E) AND ADAPTER (J) ARE COOL before handling.
- The LED panel (F) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
- Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
Caution!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. INDOOR USE ONLY.
Operating Instructions
WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED.
- Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
- Connect power adapter input (G) into connector (H) in the rear-bottom of the lamp.
- Plug the power adapter (J) into a standard household 120V AC outlet.
Note: Only use with the supplied power adapter to avoid damage or fire.
- Touch the ON/OFF button (B) to power ON or power OFF the lamp.
- There are six levels of brightness. Brightness can be adjusted by either touching or sliding a finger over the dimmer panel (C).
NOTE: If dimmer function was employed prior to turning "OFF" lamp, the lamp will return to lamp setting last employed unless disconnected from adapter.
- Control panel (K) is used to set the lamp's calendar, alarm setting, and display screen light setting. See respective sections for Operating Instructions below.
- To reposition the light, hold base (A) steady and grasp either lamp body (D) or shade (E) depending on needed adjustment.
- The lamp body (D) and shade (E) can be adjusted. The lamp head can pivot up to 90 degrees vertically and the main arm can extend to allow the lamp head to be positioned over a wider area, demonstrating a maximum adjustment range of 180 degrees horizontally. NOTE: DO NOT FORCE the shade or lamp body outside allowable adjustable range as excessive adjustment may cause damage.
Parts Description:
- A: Lamp body base
- B: ON/OFF button (also part of the dimmer panel)
- C: Dimmer panel (sliding control for brightness)
- D: Lamp body (main arm)
- E: Lamp head
- F: LED panel (light source)
- G: Power adapter input (port on lamp)
- H: Connector (on lamp, for power adapter)
- J: Power adapter (external power supply)
- K: Control panel (located on the backside of lamp body D)
- L: USB output port (for charging devices)
Diagram Descriptions:
- Diagram 1 & 2 (Adjustment Range): These diagrams illustrate the maximum adjustment range of the lamp. The lamp head can pivot up to 90 degrees vertically from its upright position, and the main arm can extend and pivot to allow the lamp head to be positioned over a wider area, demonstrating a horizontal adjustment range of 180 degrees.
- Diagram 3 (Battery Replacement): This diagram shows the process of replacing the CR2032 battery. It depicts the battery compartment on the backside of the lamp body (D) and indicates the use of a screwdriver to open it. The CR2032 3V battery is shown with its positive (+) terminal.
Calendar and Clock Setting
NOTE: Control Panel (K) is located on the backside of lamp body (D) for setting Calendar and Clock.
- To set time: Push the ⚙️ (setting) key, and the "hour" will flicker. Then touch the ▲ (up) key and ▼ (down) key to adjust the "hour." After setting the "hour," touch the ⚙️ (setting) key again to set the "minute," "year," "month," and "day."
NOTE: Day of week changes automatically with date change.
- In setting mode, touch the M (mode) button to exit the function, or operation will stop in one minute.
- When not in setting mode, touch the ▲ (up) key to switch between "12h" and "24h" display.
Alarm & Snooze Function Setting
- To set the alarm time: Press the M (mode) button located on control panel (K) to activate alarm setting mode. In alarm mode, touch the ⚙️ (setting) button to set the alarm time sequence: "Hour," "Minute," "Snooze," "Music," then exit.
NOTE: There are 8-music tones to select.
- Touch the ▲ (up) key and ▼ (down) key to adjust the alarm time sequence.
- To activate the alarm: Press the M (mode) button to activate the alarm setting mode, and then press the ▲ (up) key and ▼ (down) key to turn ON/OFF the alarm and snooze function. A music note ? will light up on the digital display to indicate the alarm is set. Z² will light up to indicate snooze is activated.
- When the alarm time is reached, the alarm will ring for 1-minute, then snooze and ring again. Touch the ⚙️ (setting) key to turn off the alarm, or touch the ▲ (up) key or ▼ (down) key to activate snooze.
NOTE: Snooze defaults to 60-minutes if loss of power occurs.
Temperature Switch Setting
- In normal mode, touch the ▼ (down) key to switch between °F and °C display.
- To adjust display screen brightness, touch the ✉️ (display key) to choose a suitable brightness setting.
NOTE: Display screen defaults to "highest" brightness setting when power initially applied.
Control Panel (K) Icon Legend
- ⚙️ (setting) button: To set the calendar; in alarm mode, push to turn off the alarm.
- M (mode) button: Push to set the alarm and snooze.
- ▲ (up) button: In setting mode, push to increase.
- ▼ (down) button: In setting mode, push to decrease.
- ✉️ (display key): Push for suitable brightness.
FCC Part 15
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.
Power Adapter Specification
- Input: AC 100-240V, 50/60 Hz, 0.9A
- Output: 27V DC, 1.0A with a Male DC Plug
This lamp contains a 5V, 2.1A USB output port (L) located on the bottom rear of the lamp. The USB port can charge items such as tablets, smartphones, etc.
Product Models
The OttLite Renew LED Desk Lamp is available under the following model numbers:
- FIDY8BW9
- FIDY8BW9-SHPR
- F1DY8G59
- F1DY8G59-SHPR
- F1DY81G9
- F1DY8009
- U13FS
