Fortin EVO-ALL Installation Guide
For Toyota Hilux (2015-2020) with Push-to-Start
Regular Installation
Guide #: 76161
This guide provides instructions for the regular installation of the Fortin EVO-ALL module for Toyota Hilux vehicles (2015-2020) with a Push-to-Start system.
Vehicle Compatibility:
- Make: TOYOTA
- Model: Hilux
- Years: PTS 2015-2020
Module Information:
- Compatible Module Required: EVO-ALL
- Manufactured After: 2019
- Firmware Version: 79.[66] MINIMUM
Programming Tools:
To add firmware versions and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).
Unit Option Units:
- C1: OEM Remote status (Lock/Unlock) monitoring
- D6: Push-to-Start
Parts Required: 1x Fuse
Note: The vehicle's OEM remote will not be operable during remote start.
Mandatory Installation Requirements
Hood Pin: The hood status pin switch must be installed. If the vehicle can be remote started with the hood open, program function A11 to OFF.
Safety Notice: The installation of safety elements is mandatory. The hood pin is an essential security element and must be installed.
Technician Requirement: This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.
Wiring Connections
Refer to the following diagrams for connection points:
- 1. Light control switch: Located behind the driver's foot lining.
- 2. Certification unit connectors: Located behind the instrument cluster.
- 3. Certification unit connectors: Located behind the instrument cluster.
- 4. Adapter connector: Located behind the lining at the driver's foot.
Key Connection Points:
- (-) DRIVER DOOR BUTTON
- (-) STEERING LOCK
- (-) START/STOP
- (+) IGNITION
- (-) CAN LOW
- (-) CAN HIGH
- (+) 12V
- (-) HOOD
- (-) HAND BRAKE
- (-) TRUNK RELEASE
- (+/-) TACHOMETER
- (-) GROUND OUT WHILE RUNNING
- (+/-) TACHOMETER
- (-) FOOT BRAKE
- (-) TRUNK
- (-) DOOR STATUS
- (-) LOCK
- (-) UNLOCK
- (-) PARKING LIGHTS
- (-) AUTOLIGHT OFF
Wiring Diagram Overview:
The diagram illustrates connections between the EVO-ALL module, the remote starter, and various vehicle components including ignition, door locks, lights, and CAN bus.
Dcryptor Programming Procedure
Parts Required (not included): FLASH LINK UPDATER, FLASH LINK MANAGER SOFTWARE, or FLASH LINK MOBILE APP. A Microsoft Windows computer or a smartphone with internet connection is also required.
- Preparation: Press and hold the programming button. Connect the 4-PIN Data-link connector. The LEDs (BLUE, RED, YELLOW, BLUE & RED) will illuminate alternatively.
- Release: Release the programming button when the LED turns BLUE. If the LED is not solid BLUE, disconnect and restart from Step 1.
- Connectors: Insert the required remaining connectors.
- Ignition ON: Do not press the brake pedal. Press the Push-to-Start button twice to turn on the ignition. Wait for the BLUE LED to flash rapidly and constantly.
- Ignition OFF: Press the Push-to-Start button once to turn off the ignition. The BLUE LED will turn off.
- Disconnect: Disconnect all connectors, including the Data-Link (4-pins) connector.
- Programming Tool: Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the Dcryptor menu.
- Reconnect: After Dcryptor programming is complete, reconnect the 4-Pin (Data-Link) connector and then all other connectors to the EVO-ALL module.
Note: If the RED and YELLOW LEDs alternate during programming, proceed to Step 6 of the Dcryptor process. If the LEDs turn OFF, the module is programmed.
Remote Starter Functionality
To start the vehicle remotely:
- Ensure all doors are closed.
- Press the remote start button located on the driver's side door handle.
- The engine will shut down when the button is pressed again.
- Enter the vehicle with the Smart-Key.
- Press the brake pedal.
- Press the Push-to-Start button to start the vehicle.
- The vehicle can now be put into gear and driven.
Verification
Test the remote starter and alarm functions to ensure proper operation.
Notice & Warning
Updated Firmware and Installation Guides: Regularly check the Fortin website (www.fortin.ca) for the latest firmware and installation guides. Update the module to the latest firmware before installation.
WARNING: The information provided is on an "as is" basis. The installer is solely responsible for verifying circuits before connection. Fortin Electronic Systems is not liable for any inaccuracies or installation errors. Installation must be performed by a qualified technician. This guide is for informational purposes only and is subject to change without notice.
Tech Support:
- Phone: 514-255-HELP (4357) / 1-877-336-7797
- Website: www.fortinbypass.com
