Fortin EVO-ALL Standalone Installation & Programming Guide

Compatibility and Warnings

Compatibility:

• Only compatible with Automatic Transmission vehicles.
• Specifically for Mazda CX-5 models with Push-to-Start ignition, model years 2017-2020.

Important Warnings:

• This module MUST be installed by a QUALIFIED TECHNICIAN. Incorrect connections can cause PERMANENT DAMAGE to the vehicle.
• Safety elements, such as the hood pin and valet switch, are mandatory and must be installed.

Required Parts and Tools

Parts Required (Not Included):

• 1x 10 AMP Fuse
• 1x 10 AMP Fuse (for bypass option)
• RSPB (sold separately)

Software/Tools Required:

• FLASH LINK UPDATER or FLASH LINK MANAGER software (requires a Microsoft Windows computer with internet connection).
• FLASH LINK MOBILE app (requires an Android or iOS smartphone with internet connection).

Other Components:

• Hood Pin Switch
• Valet Switch

Standalone Configuration Options

The EVO-ALL module supports various bypass and remote start configurations:

Remote Starter Functionality

To initiate remote start:

1. Ensure all doors are closed.
2. Press the OEM remote's Lock button 3 times consecutively.
3. The vehicle will start.

To unlock doors:

• Use either the OEM remote or the remote-starter remote.

Important Notes:

• The module will shut down the vehicle if the driver's door is opened after remote start.
• To drive the vehicle, enter with the Smart-Key, press the brake pedal (or clutch for manual transmission), and then press the Push-to-Start button.

Installation Procedure Overview

Safety First: Always disconnect the negative terminal (-) of the vehicle battery before performing any work. This is crucial for protecting sensitive electronic modules.

1. Battery Disconnection: Locate the vehicle battery and disconnect the negative terminal.
2. Accessing Steering Column:
   • Under the steering column, unscrew any retaining screws (typically 1 and 2).
   • Gently unclip or detach covers on the left and right sides of the steering column (steps 3 and 4).
   • Carefully pull up the steering column cover to gain access (step 5).
3. Wiring Connections: Refer to the detailed wiring diagrams provided in this guide to make the necessary connections. Ensure all connections are secure and correct.
4. Battery Reconnection: Once all connections are made, reconnect the negative terminal of the vehicle battery.

Wiring Diagram Details

The following are key connection points and wire functions identified in the diagrams:

• Under Steering Column (START-STOP Unit):
  • (+)12V (Yellow wire)
  • (+)IGNITION (Pink wire)
  • CAN LOW (Orange wire)
  • CAN HIGH (Orange/Black wire)
  • (-)PTS (Purple wire)
  • DOOR LOCK DATA (Lt.Blue/Black wire)
  • DATA KEY (Black wire)
• Parking Light Connections:
  • (-)PARKING LIGHTS (COM) (Brown/White wire)
  • (-)PARKING LIGHTS (NO) (Pink/Black wire)
  • (-)PARKING LIGHTS (NC) (Purple/Yellow wire)
• Engine Compartment Connections (for vehicles without OEM Hood Pin):
  • Connections are made to specific pins in connectors located in the engine compartment. Refer to the diagrams for exact pin locations and wire colors (e.g., Ground, (+)12V Battery, etc.).
• Data-Link Harness (4-pin, Black Connector): Used for programming and communication between the module and the vehicle's systems.

Note: Detailed diagrams illustrate specific wire routing and connector pin assignments for each connection point.

Programming Procedures

Key Bypass Programming (Procedure 1/6)

Important: Do not program more than 3 modules on the same vehicle. If more than 3 modules are programmed, the remote car starter may not function.

1. Ensure you have two valid vehicle keys.
2. Press and hold the programming button on the EVO-ALL module.
3. Connect the 4-PIN Data-link harness (black connector). The Blue, Red, Yellow, and Blue & Red LEDs will illuminate alternately.
4. Release the programming button when the Blue & Red LEDs are solid ON. If not solid, disconnect the harness and repeat from step 2.
5. Connect the required remaining harnesses.
6. Press and release the programming button five times (5x). The Red & Blue LEDs will alternate between 4 flashes and a pause. Wait for the Blue LED to turn ON.

Programming OEM Keys (KEY#1 and KEY#2)

7. For KEY#1: Place the first OEM remote near the START/STOP button. Press the START/STOP button twice to activate ignition. The Yellow LED will turn ON. Wait for the security indicator to turn OFF (approx. 3 seconds).
8. Immediately: Press the START/STOP button once to deactivate ignition. The Yellow LED will turn OFF.
9. For KEY#2: Place the second OEM remote near the START/STOP button. Press the START/STOP button twice to activate ignition. The Yellow LED will turn ON.
10. Wait for the security indicator to turn OFF (approx. 3 seconds).
11. Immediately: Press the START/STOP button once to deactivate ignition. The Yellow LED will turn OFF.
12. The vehicle's ignition will turn ON, followed by the Yellow and Red LEDs illuminating alternately.
13. The vehicle's ignition will then turn OFF.
14. Disconnect all harnesses, including the 4-PIN Data-link harness.

Video Tutorial: For a visual guide, visit: http://youtu.be/5ETmJn9RIIE

DCryptor Programming (using Flash Link)

1. Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to access the DCryptor menu.
2. After completing DCryptor programming, return to the vehicle and reconnect the 4-PIN (Data-Link) connector, followed by all other EVO-ALL connectors.
3. Repeat steps 1 to 12 of the Key Bypass Programming procedure.
4. Observe vehicle ignition status (ON/OFF) and LED indicators (Blue/Red flashing) as per the guide.
5. Disconnect all harnesses, then disconnect the 4-PIN Data-link harness.

CAN Programming Procedure

1. Press and hold the programming button. Connect the 4-PIN Data-link harness (black connector). LEDs (Blue, Red, Yellow, Blue & Red) will illuminate alternately.
2. Release the programming button when the Blue LED is ON. If the Blue LED is not solid ON, disconnect the 4-PIN Data-link harness.
3. Connect the required remaining harnesses.
4. Press the START/STOP button twice to turn ON the vehicle's ignition. The Blue LED will flash rapidly.
5. Press the START/STOP button once to turn OFF the vehicle's ignition. The Blue LED will turn OFF, and the Red LED will turn ON.
6. The module is now programmed.

Remote Starter Diagnostics

Diagnostic codes are indicated by the module's RED LED:

• 2x flash: Brake ON
• 3x flash: No tach signal
• 4x flash: Ignition detected before start
• 5x flash: Hood Open
• 4x flash (Parking Lights): FOB in car
• 5x flash (Parking Lights): Hood Open
• 6x flash (Parking Lights): Brake ON
• 7x flash (Parking Lights): Door Open
• 8x flash (Parking Lights): Bad Encryption / Key Code

Important Notices

Firmware Updates: Regularly check the Fortin website (www.fortin.ca) for the latest firmware and installation guides. Update the module before installation.

Disclaimer: The information provided is a guide and is subject to change without notice. Fortin Electronic Systems is not liable for installation errors or damages. Installation is the sole responsibility of the installer. Only qualified technicians should perform installations.

Contact Information:

• Tech Support: 514-255-HELP (4357) or 1-877-336-7797
• Website: www.fortinbypass.com