EVO-ONE | All-In-One Remote Starter, Alarm, Immobilizer Bypass and Data Interface Module. | Fortin Electronic Systems
ONE Page 1 / 6 REV.: 20230302 GUIDE # 71481 THAR-ONE-TOY5 THARNESS INSTALLATION INSTALLATION HARNAIS THAR-ONE-TOY5 ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé) Transponder Bypass T-harness Harnais en T Lock Unlock Arm Disarm Parking Lights Autolight Off Tachometer Door Status Hand-Brake Status Foot-Brake Status OEM remote Monitoring R.S. OEM remote Stand Alone compatible VEHICLE VEHICULES TOYOTA Tacoma H-KEY YEARS ANNÉES 2016-2023 · · ············ MODEL: EVO-ONE DATE:02/2019 FORTIN.CA SN: 000000 00000 2019 MADE IN CANADA © 2018 ALL RIGHTS RESERVED COMPATIBLE MODULE REQUIRED: QR CODE ON THE LABEL MANUFACTURED AFTER: 2019 MODULE COMPATIBLE CODE QR SUR L'ÉTIQUETTE REQUIS: FABRIQUÉ APRÈS: 2019 FIRMWARE VERSION VERSION LOGICIELLE 79.[66] TOYOTA/ LEXUS MINIMUM To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately. Pour ajouter la version logicielle et les options, utilisez l'outil FLASH LINK UPDATER ou FLASH LINK MOBILE, vendu séparément. Program bypass option: Programmez l'option du contournement: UNIT OPTION OPTION UNITE C1 IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN: SI LE VÉHICULE N'EST PAS ÉQUIPÉ D'UN CONTACT DE CAPOT FONCTIONNEL: D5 A11 OFF NON DESCRIPTION OEM Remote status (Lock/Unlock) monitoring Suivi des status (Verrouillage/Déverrouillage) de la télécommande d'origine Lock after start Verrouillage après le démarrage Hood trigger (Output Status). Contact de capot (état de sortie). Program remote starter option: Programmez l'option démarreur à distance: Program remote starter option for R.S. OEM REMOTE STAND ALONE: Programmez l'option démarreur à distance pour TÉLÉCOMMANDE D'ORIGINE STAND ALONE: FUNCTION FONCTION 2 38 MODE 4 2 DESCRIPTION (+) Start 2 (E1) (+) Ignition 2 (E2) (+) Démarreur 2 (E1) (+) Ignition 2 (E2) Enable Press 3x Lock to remote start with the OEM remote. Activé Appuyez x3 sur Verrouille de la télécommance d'origine pour démarrer à distance le véhicule. MANDATORY INSTALL | INSTALLATION OBLIGATOIRE * HOOD PIN CONTACT DE CAPOT HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE A11 OFF NON REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF. STATUT DE CAPOT : LE CONTACT DE CAPOT (INCLUS), DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON. SECURITY STICKER AUTOCOLLANT DE SÉCURITÉ WARNING ATTENTION Included Inclus Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot et l'autocollant de sécurité sont des éléments de sécurité essentiels et doivent absolument être installés. THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE. CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES PERMANENTS AU VÉHICULE. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. DESCRIPTION | DESCRIPTION Page 2 / 6 At BCM Au BCM TPMS Ignition switch Commutateur d'Ignition OBD-II connector Connecteur OBD-II This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. WIRING CONNECTION | GUIDE DE BRANCHEMENTS HOOD PIN CONTACT CAPOT Yellow In AA11 Purple Out AA22 Purple/White Out AA33 Green Out AA44 White Out AA55 (-)Disarm Orange Out AA66 Orange/Black Out AA77 Dk.Blue Out AA88 Red/Blue In AA99 Lt.Blue/Black In/Out AA1100 Black In AA1111 Pink Out AA1122 Yellow/Black Out AA1133 Brown/White In AA1144 (-) Hood pin Pink/Black In AA1155 Purple/Yellow In/Out AA1166 Green/White In/Out AA1177 Green/Red In/Out AA1188 White/Black Out AA1199 Lt.Blue In/Out AA2200 (-)Ground White Out EE11 Orange Out EE22 Red In EE33 Black In EE44 Pink In/Out EE55 Yellow Out EE66 CUT LOOP FOR AUTOMATIC TRANSMISSION MODE. COUPEZ LA BOUCLE POUR LE MODE TRANSMISSION AUTOMATIQUE. C5 Brown C4 Gray/Black C3 Gray C2 Orange/Brow5 PnIN CONN. C1 Orange/Green D6 White/Red D5 White/Blue D4 White/Green D3 Yellow/Red D2 Yellow/Blue D1 Yellow/Green (~)TPMS (~)TPMS Page 3 / 6 Ground Masse CUT ----------- T-HARNESS - HARNAIS EN T THAR-TY20 ISOLATE NOT CONNECTED ISOLER NON BRANCHÉ Yellow/Black Jaune/Noir D4 Tacoma 36 27 12 35 26 34 25 11 33 24 10 32 23 31 22 9 30 21 8 29 20 28 19 7 18 6 17 5 16 4 15 3 14 2 13 1 D6 TPMS Lt.Green or Pink Vert Pâle ou Rose CONNECTION ONLY REQUIRED IF REMOTE START CONTROL FROM OEM REMOTES IS DESIRED AND VEHICLE IS EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEM (TPMS). CONNEXION UNIQUEMENT REQUISE SI LE CONTRÔLE DE DÉMARRAGE À DISTANCE DE LA TÉLÉCOMMANDES D'ORIGINE EST DÉSIRÉ ET LE VÉHICULE EST ÉQUIPÉ D'UN SYSTÈMES DE CONTRÔLE DE PRESSION DE PNEU (TPMS). Back view White 36-pin connector At BCM Vue de dos Connecteur Blanc de 36-pins Au BCM T-HARNESS - HARNAIS EN T THAR-TOY5 654 3 22 1 18 17 16 15 14 13 12 11 10 9 8 7 30 29 28 27 26 25 24 23 22 21 20 19 If equiped with OEM Alarm Si équippé d'une Alarme d'origine Back view - White 30-pin connector, at BCM Vue de dos - Connecteur Blanc, 30-pins, au BCM. Back view White connector Ignition harness Vue de dos Connecteur Blanc Harnais Ignition OBDII connector Front view Connecteur OBDII Vue de face This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. KEY BYPASS PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ Page 4 / 6 J H B C D G F A E Do not use the grey key. Ne pas utiliser la clé grise. 1 x1 HOLD 2 RELEASE 3 4 x10 PRESS 5 TURN ON/RUN 6 TURN OFF G F A E J H B C D G F A E J H B C D G F A E J H B C D G F A E J H B C D LOCK LOCK I I I I START I I I I J H B C D LED may differ depending on the module casing. apparence des DELS peut différer selon le boîtier du module. ON BLUE BLEU ON RED ROUGE J H B C D Press and hold the programming button: Insert the 6-Pin Main connector. The LEDs will alternate between BLUE, RED,YELLOW & BLUE/RED flashes. Appuyez et maintenir le bouton de programmation enfoncé: Insérez le connecteur Principal à 6-broches. Les DELS alterneront entre un clignotement BLEU, ROUGE, JAUNE & BLEU/ROUGE. Release the programming button when the LED's are RED and BLUE. Relâchez le bouton de programmation quand les DELs sont ROUGE et BLEU. If the LED's are not solid BLUE and RED disconnect the 6Pin connector (MainHarness) and go back to step 1. Si le DEL ne sont pas BLEU et ROUGE débranchez le connecteur 6 pins (Connecteur principal) et allez au début de l'étape 1. Insert the required remaining Insérez les connecteurs requis connectors. restants. I J H B C D G F A E G F A E G F A E PRESS X10 FLASH X9 ON ON Press and release the ... programming button ten (10x) times. ... The RED and BLUE LED's will alternate between 9 flashes and a pause. Appuyez et relâchez 10 fois le bouton de programmation. Les DELs ROUGE et BLEU alterneront entre 9 clignotements et une pause. ACC ON IGN PUSH G J F A H B C E D IGNITION ON FLASH 10X FLASH 10X FLASH 10X FLASH Turn the Ignition to the ON/RUN position. The RED and BLUE LED's will flash rapidly 10x times. Key bypass programmed. The BLUE LED will flash rapidly. CAN-Bus programmed. Tournez la clé en position ignition (ON). Les DELs BLEUE et ROUGE clignoteront 10x fois rapidement. Contournement de clé programmé. La DEL BLEUE clignotera rapidement: Réseau CAN program.mé I START OFF ACC ON PUSH G J F A H B C E D IGNITION ON IGNITION OFF Turn the Ignition to the OFF OFF position. The BLUE LED will turn off. Tournez la clé à OFF. La DEL BLEU s'éteint. The module is now programmed. Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming. Le module est programmé. Testez toutes les fonctions supportées sur le véhicule avec la télécommande du démarreur à distance ou du système de sécurité. This guide may change without notice. See www.fortin.ca for latest version. Ce guide peut faire l'objet de changement sans préavis. Voir www.fortin.ca pour la récente version. Page 5 / 6 REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING. RÉFÉREZ-VOUS AU GUIDE D'INSTALLATION RAPIDE INCLUS AVEC LE MODULE POUR LA PROGRAMMATION DU DÉMARREUR À DISTANCE. REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE Start UNLOCK TURN ON/RUN ON All doors must be closed. Toutes les portes doivent être fermées. Remote start the vehicle. Démarrez à distance. Unlock the doors with the remote-starter remote or the OEM remote. Déverrouillez les portes avec la télécomande du démarreur à distance ou la télécommande d'origine. Insert and Turn the key to the Ignition ON/RUN position. Insérez et tournez la clé à la position "ON/RUN". Press the brake pedal. Appuyez sur la pédale de frein. The vehicle can now be put in to gear and driven. Vous êtes maintenant prêt à embrayer et prendre la route. Page 6 / 6 ONE MODEL: EVO-ONE DATE:02/2019 FORTIN.CA SN: 000000 00000 MADE IN CANADA © 2018 ALL RIGHTS RESERVED Module label | Étiquette sur le module Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product. Notice: Mise à jour microprogramme et Guides d'installations Des mises à jour du Firmware (microprogramme) et des guides d'installation sont mis en ligne régulièrement. Vérifiez que vous avez bien la dernière version logiciel et le dernier guide d'installation avant l'installation de ce produit. WARNING The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version. MISE EN GARDE L'information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d'exactitude. Il est de la seule responsabilité de l'installateur de vérifier tous les fils et circuits avant d'effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité de l'exactitude de l'information fournie. L'installation (dans chaque cas) est la responsabilité de l'installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n'assume aucune responsabilité suite à l'installation, que celle-ci soit bonne, mauvaise ou de n'importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifié. L'information fournie dans ce guide est une suggestion. Ce guide d'instruction peut faire l'objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version. Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING TECH SUPPORT Tél: 514-255-HELP (4357) 1-877-336-7797 ADDENDUM GUIDE www.fortinbypass.com WEB UPDATE | MISE À JOUR INTERNETAdobe PDF Library 16.0.7 Adobe InDesign 17.4 (Windows)