Fortin EVO-ALL Installation Guide for Mazda CX-5 (2017-2020) Push-to-Start

This guide provides instructions for installing the Fortin EVO-ALL bypass and interface module in a Mazda CX-5 equipped with a Push-to-Start system.

Vehicle Compatibility

Make: Mazda

Model: CX-5

Year Range: 2017-2020

System Type: Push-to-Start

Module Information

Module: EVO-ALL

Firmware Version: 85.[11] (Minimum)

Programming Tool: FLASH LINK UPDATER or FLASH LINK MOBILE (sold separately)

Important Notes & Warnings

Installation Warning: This module must be installed by a qualified technician. Incorrect wiring can cause permanent damage to the vehicle.

Hood Pin Requirement: If the vehicle is not equipped with a functional hood pin, the A11 option (Hood Trigger) must be set to OFF (NON). The hood pin is an essential security element and must be installed.

Battery Disconnection: Always disconnect the negative (-) terminal of the vehicle's battery before disconnecting any module, computer, or control unit. The factory keyless entry module is sensitive to interference.

Wiring Configuration

Refer to the wiring diagrams provided for specific connections. Key connection points include:

Under Steering Column (START-STOP Unit): Connections for +12V, +IGNITION1, +STARTER, -PTS, +ACCESSORY, GROUND, CAN LOW, CAN HIGH, DOOR LOCK DATA, +IGNITION2.
Parking Light Switch: Connection for (-)PARKING LIGHT.

Wiring Diagram Overview: The diagrams illustrate connections for both automatic and manual transmissions, detailing the integration with the vehicle's harness and the EVO-ALL module.

Programming Procedure (DCryptor)

Parts Required (not included): FLASH LINK UPDATER, FLASH LINK MANAGER software, or FLASH LINK MOBILE app, and a Microsoft Windows computer or Android/iOS smartphone with internet connection.

Set Options: Before programming, set the unit options and save them using the appropriate tool.
Enter Programming Mode: Press and hold the programming button. Connect the 4-PIN Data-link harness. The Blue, Red, Yellow, and Blue & Red LEDs will illuminate alternatively.
Release Button: Release the programming button when the Blue LED is ON. If the Blue LED is not solid, repeat step 1.
Connect Harnesses: Connect the remaining required harnesses.
Ignition ON: Do not press the brake pedal. Press the Push-to-Start button twice to turn ON the ignition. The Blue, Red, and Yellow LEDs will illuminate alternatively.
Wait for Flash: Wait for the Blue LED to flash rapidly.
Ignition OFF: Press the Push-to-Start button once to turn OFF the ignition. The Blue LED will turn off. The Red and Yellow LEDs will alternate.
Disconnect: Disconnect all connectors, including the Data-Link (4-pins) connector.
Use Flash Link Tool: Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCryptor menu.
Reconnect: After programming, reconnect the 4-Pin Data-Link connector and then all other connectors.

Remote Starter Functionality

Preparation: Ensure all doors are closed.
Remote Start: Use the OEM remote or the remote-starter remote to start the vehicle.
Unlock Doors: Unlock the doors using either the OEM remote or the remote-starter remote.
Enter Vehicle: Enter the vehicle with the Smart-Key.
Brake Pedal: Do NOT press the brake pedal.
Ignition Cycle: Press and release the Push-to-Start button once. Wait for the orange LED on the Push-to-Start button to turn on and off twice.
Drive: Press the brake pedal. The vehicle can now be put into gear and driven. If the Smart-Key is not detected, the vehicle will shut down.

Technical Support

For technical support, contact Fortin at:

Phone: 514-255-HELP (4357) or 1-877-336-7797
Website: www.fortinbypass.com

Notices

Firmware Updates: Updated firmware and installation guides are available on the Fortin website. It is recommended to update the module to the latest firmware and download the latest installation guide.

Disclaimer: The information in this guide is provided as-is. Fortin Electronic Systems assumes no liability for the accuracy or currency of the information, or for any installation performed. Installation is the sole responsibility of the installer. This guide is for suggestion purposes only and may change without notice.

	Fortin EVO-ALL Installation Guide for Toyota Hilux (2015-2020) Push-to-Start Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module for Toyota Hilux vehicles equipped with push-to-start systems (2015-2020). Covers wiring, programming, and functionality.
	Fortin EVO-ONE Installation Guide for Honda Civic (2016-2021) Comprehensive installation guide for the Fortin EVO-ONE remote starter and alarm system for Honda Civic models from 2016 to 2021. Includes wiring diagrams, programming procedures, and functionality details.
	Fortin EVO-ALL Stand Alone Installation Guide for Lexus UX250H Comprehensive installation guide for the Fortin EVO-ALL remote starter and bypass module for the 2019-2024 Lexus UX250H, covering wiring, programming, and functionality.
	Fortin EVO-ALL Installation Guide for Jeep Cherokee (2019-2021) This guide provides detailed instructions for installing the Fortin EVO-ALL remote start and bypass module in a Jeep Cherokee (2019-2021 Tip-key). It covers wiring, programming procedures, vehicle compatibility, and important safety notes.
	Fortin EVO-ONE THAR-ONE-TOY5 Harness Installation Guide for Toyota Tacoma Detailed installation and programming guide for the Fortin EVO-ONE and THAR-ONE-TOY5 harness for Toyota Tacoma (2016-2023) H-Key vehicles. Covers wiring, key bypass, and remote starter functions.
	Fortin THAR-VW1 Installation Guide for Volkswagen Golf (2015-2018) Push-to-Start This guide provides detailed instructions for installing the Fortin THAR-VW1 remote starter and bypass module in Volkswagen Golf vehicles equipped with push-to-start ignition, model years 2015-2018. It includes wiring diagrams, programming procedures, and functionality explanations.
	Fortin EVO-ONE Installation Guide for Honda Civic (2022) Push-to-Start Comprehensive installation guide for the Fortin EVO-ONE remote starter, alarm, and immobilizer bypass module for the 2022 Honda Civic with Push-to-Start. Includes wiring diagrams, programming procedures, and functionality details.
	Fortin EVO-ONE THAR-GM6 Installation Guide for Chevrolet Equinox (2018-2024) Comprehensive installation and programming guide for the Fortin EVO-ONE and THAR-GM6 bypass module for Chevrolet Equinox models with Push-to-Start. Includes wiring, setup, and remote start functionality.