Fortin EVO ONE Remote Starter Installation Guide for Chevrolet Spark

Vehicle Compatibility

Vehicle Make: Chevrolet

Model: Spark

Key Type: Standard Key

Model Years: 2016-2019

Module Firmware Version: 70.[41] GM MINIMUM

Guide Number: 90441

Revision Date: 20211209

Supported Vehicle Functions

The following vehicle functions are supported by this diagram (functional if equipped):

* Hood Status function requires the hood pin switch to be installed.

** OEM remote Monitoring function may require additional components or configurations.

Firmware and Options Configuration

To add the firmware version and configure options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Program Bypass Options:

• Option Unit: C1 - OEM Remote status (Lock/Unlock) monitoring.
• Option Unit: A11 (OFF/NON) - Hood trigger (Output Status).
• Option Unit: D2 - Unlock before / Lock after (Disarm OEM alarm).
• Option Unit: E5 (OFF/NON, ON/OUI) - By default DEACTIVATED.

Note: Modules manufactured between 04/2018 and 04/2019.

Important: The vehicle's Flip-key remote will not be functional during remote start.

Required Parts (Not Included)

• 1x 2 Amp Fuse
• 1x 180 Ohm resistor (for Manual Transmission)

Mandatory Installation Requirements

Hood Pin Switch

The hood pin switch (included) MUST be installed if the vehicle can be remote started with the hood open. Set Function A11 to OFF (NON) in this case.

Security Sticker

The installation of safety elements, including the hood pin and the security sticker, is mandatory. These are essential security components and must be installed.

Installer Qualification

⚠️ WARNING: THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

Ignition Switch Wiring

This section details connections at the ignition switch and related components.

Components:

• OBDII Connector: Located at the vehicle's diagnostic port.
• Ignition Connector: Connects to the ignition switch harness. Key wires include VDATA, 12V IGNITION, ACCESSORY.
• IMMO Connector: Connects to the immobilizer system. Key wires include DATA, IMMO POWER.
• Ignition Barrel: The physical key slot.

Automatic Transmission Wiring Diagram

This diagram illustrates the connections for vehicles with automatic transmissions.

Note: For automatic transmission mode, CUT THE LOOP for automatic transmission mode.

Main EVO ONE Harness Connections (Connectors A, E, G, H, J):

• Connector A:
  • (+)Ignition: Yellow (In A1)
  • (-)Lock: Purple (Out A2)
  • (-)Unlock: Purple/White (Out A3)
  • (-)Start: Green (Out A4)
  • (~)IMMO Power: White (Out A5)
  • (~)IMMO Power: Orange (Out A6)
  • (~)IMMO Power: Orange/Black (Out A7)
  • (~)IMMO Power: Dk. Blue (Out A8)
  • (~)IMMO Power: Red/Blue (In A9)
  • (~)Immo Data: Lt. Blue/Black (In/Out A10)
  • Black (In A11)
  • (-)Parking Lights: Pink (Out A12)
  • Yellow/Black (Out A13)
  • Brown/White (In A14)
  • (-) Hood pin: Pink/Black (In A15)
  • Purple/Yellow (In/Out A16)
  • Green/White (In/Out A17)
  • (~)VDATA: Green/Red (In/Out A18)
  • White/Black (Out A19)
  • (~)Immo Data: Lt.Blue (In/Out A20)
• Connector E:
  • (+)Accessory: White (Out E1)
  • (+)12V: Orange (Out E2)
  • Red (In E3)
  • Black (In E4)
  • Pink (In/Out E5)
  • Yellow (Out E6)
• Connector G: (CAN SW)
• Connector H: (CAN SW)
• Connector J: (CAN SW)

Other Connections:

• 2 Amp Fuse: Connected between D2 and D3.
• Ground: Black wire to vehicle ground.

Vehicle Connectors:

• 4. Back view 12-Pin Black Connector (Headlamp switch)
• 3. Back view 27-Pin Grey Connector At BCM
• 1. Back view 27-Pin Pink Connector At BCM
• 2. Ignition barrel
• 5. Back view 3-Pin Burgundy Connector (Key Bypass IMMO connector)
• 6. Back view 6-Pin Black Connector (Ignition Connector)
• OBDII (3. Front view)

Note: *If the vehicle is not equipped with the ON-STAR® system.

Manual Transmission Wiring Diagram

This diagram illustrates the connections for vehicles with manual transmissions.

Note: Includes a 1A Diode and a 180 ohm Resistor.

Main EVO ONE Harness Connections (Connectors A, E, G, H, J):

• Connector A:
  • (+)Ignition: Yellow (In A1)
  • (-)Lock: Purple (Out A2)
  • (-)Unlock: Purple/White (Out A3)
  • (-)Start: Green (Out A4)
  • (~)IMMO Power: White (Out A5)
  • (~)IMMO Power: Orange (Out A6)
  • (~)IMMO Power: Orange/Black (Out A7)
  • (~)IMMO Power: Dk. Blue (Out A8)
  • (~)IMMO Power: Red/Blue (In A9)
  • (~)Immo Data: Lt. Blue/Black (In/Out A10)
  • Black (In A11)
  • (-)Parking Lights: Pink (Out A12)
  • Yellow/Black (Out A13)
  • Brown/White (In A14)
  • (-) Hood pin: Pink/Black (In A15)
  • Purple/Yellow (In/Out A16)
  • (~)VDATA: Green/White (In/Out A17)
  • (~)VDATA: Green/Red (In/Out A18)
  • White/Black (Out A19)
  • (~)Immo Data: Lt.Blue (In/Out A20)
• Connector E:
  • (+)Accessory: White (Out E1)
  • (+)12V: Orange (Out E2)
  • Red (In E3)
  • Black (In E4)
  • Pink (In/Out E5)
  • Yellow (Out E6)
• Connector G: (CAN SW)
• Connector H: (CAN SW)
• Connector J: (CAN SW)

Other Connections:

• 180 ohm Resistor: Connected between A9 and D4.
• 2 Amp Fuse: Connected between D2 and D3.
• 1A Diode: Connected in line with (+)Ignition.
• Ground: Black wire to vehicle ground.

Vehicle Connectors:

• 4. Back view 12-Pin Black Connector (Headlamp switch)
• 3. Back view 27-Pin Grey Connector At BCM
• 1. Back view 27-Pin Pink Connector At BCM
• 2. Ignition barrel
• Back view 3-Pin Black Connector at Switch
• 5. Back view 3-Pin Burgundy Connector (Key Bypass IMMO connector)
• 6. Back view 6-Pin Black Connector (Ignition Connector)
• OBDII (3. Front view)

Note: *If the vehicle is not equipped with the ON-STAR® system.

DCryptor Programming Procedure

Follow these steps to program the module using the DCryptor system.

Parts Required for Programming:

• FLASH LINK UPDATER, FLASH LINK MANAGER software OR FLASH LINK MOBILE APP
• Microsoft Windows Computer with Internet connection OR Android/iOS Smartphone with Internet connection

Before Programming: Set the unit options and save them.

1. Step 1: Press and hold the programming button. Insert the 6-Pin Main connector.
   If the LED is not solid YELLOW, disconnect the 6-Pin connector and return to Step 1.
2. Step 2: Release the programming button when the LED is YELLOW.
3. Step 3: Insert the required remaining connectors.
4. Step 4: Press and release the programming button five times (5x). The YELLOW LED will alternate between 5 flashes and a pause. Wait until the YELLOW LED turns ON.
5. Step 5: Turn the ignition to the ON/RUN position. The RED LED will turn ON, and the YELLOW LED will turn OFF.
   If the LED is not solid RED, disconnect the 6-Pin connector and return to Step 1.
6. Step 6: Turn the ignition to the OFF position.
7. Step 7: Remove the key from the ignition barrel. ?
8. Step 8: Wait 5 seconds. ⏳
9. Step 9: Turn the ignition to the ON position. ?
   • The BLUE LED will turn ON. ?
   • Wait for the BLUE & RED LEDs to turn OFF.
   • Wait for the YELLOW LED to flash. ?✨
   • Wait for the YELLOW LED to turn OFF.
   • Wait for the BLUE LED to flash rapidly. ?✨
   • If LEDs do not react as shown, disconnect the 6-Pin connector and return to Step 1.
10. Step 10: Turn the ignition to the OFF position. The BLUE LED will flash slowly. ?✨
11. Step 11: Disconnect all connectors, including the 6-Pin (Main-Harness) or 4-Pin Data-link connector.
12. Step 12: Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCryptor menu.
13. Step 13: After programming is complete, reconnect the 6-Pin (Main-Harness) or 4-Pin Data-link connector, followed by all other connectors.

The module is now programmed.

Remote Starter Functionality

Manual Transmission: Ready Mode Activation

By Default:

1. Ensure the vehicle is running. ?
2. Make sure all doors are closed and the transmission is in NEUTRAL.
3. Press the brake pedal. ?
4. Engage the parking brake. ?️
5. Release the brake pedal. ?
6. Press the START button for 3 seconds. The parking lights will flash once and remain on. ✨
7. Remove the key from the ignition barrel. The vehicle will remain running. ??
8. Exit the vehicle and close all doors. The engine will stop running once all doors are closed.
9. Ready mode is now active. Remote start is functional. If any door is open, the mode will be disabled. ❗

Choice 2:

1. Ensure the vehicle is running. ?
2. Make sure all doors are closed and the transmission is in NEUTRAL.
3. Press the brake pedal. ?
4. Engage the parking brake. ?️
5. Release the brake pedal. ?
6. Press the START button for 3 seconds. The parking lights will flash once and remain on. ✨
7. Remove the key from the ignition barrel. The vehicle will remain running. ??
8. Exit the vehicle and close all doors.
9. Lock the doors with the remote-starter remote or OEM remote. The engine will stop running. ?
10. Ready mode is now active. Remote start is functional. If any door is open, the mode will be disabled. ❗

Choice 3:

1. Ensure the vehicle is running. ?
2. Make sure all doors are closed and the transmission is in NEUTRAL.
3. Press the brake pedal. ?
4. Engage the parking brake. ?️
5. Release the brake pedal. ?
6. Remove the key from the ignition barrel. The vehicle will remain running. ??
7. Exit the vehicle and close all doors. The engine will stop running once all doors are closed.
8. Ready mode is now active. Remote start is functional. If any door is open, the mode will be disabled. ❗

Automatic Transmission: Take Over Procedure

1. Start the vehicle (normal ignition).
2. Ensure all doors are closed.
3. Remote start the vehicle. ?
4. Unlock the doors with the remote-starter remote or OEM remote. ?
5. Insert and turn the key to the Ignition ON/RUN position. ?
6. Press the brake pedal. ?
7. The vehicle can now be put into gear and driven.

Final Notes and Support

Firmware Updates

Updated firmware and installation guides are regularly posted on the Fortin website. It is recommended to update the module to the latest firmware and download the latest guide before installation.

Warning

The information provided is on an "as is" basis. It is the installer's sole responsibility to verify all circuits before connecting. Fortin Electronic Systems assumes no liability for accuracy or installation errors. Installation must be performed by a qualified technician. This guide is for informational purposes only and may change without notice. Visit www.fortinbypass.com for the latest version.

Technical Support

Phone: 514-255-HELP (4357) | 1-877-336-7797

Website: www.fortinbypass.com