Chest
Assembly Information
Assembled by 2 Adults
Brand: FUFU&GAGA
Important Information
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Assembly Tips
Avoid Scratches
To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
Improve Efficiency
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Safety Warnings
Anti-Topple Warning
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important Maintenance Notes
It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe it, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools Required
Please prepare the following tools:
- Tape Measure
- Drill
- Level
- Screwdriver
- Hammer
- Wrench
- Pencil
Hardware List
| Part | Description | Quantity |
|---|---|---|
| A | Slide rail | x 6 |
| B | Slide rail | x 6 |
| C | Screw | x 36 (3 x 12mm) |
| D | Quickfit screw | x 23 (6 x 35mm) |
| E | Part | x 2 |
| F | Screw | x 18 (4 x 14mm) |
| G | Screw | x 6 (4 x 35mm) |
| H | Screw | x 15 (4 x 30mm) |
| J | Handle part | x 3 |
| K | Screw | x 6 (4 x 18mm) |
| L | Part | x 6 |
| M | Screw | x 6 (3 x 14mm) |
| N | Anti-tipping device part | x 2 |
| P | Wooden dowel | x 8 |
| Q | Cam lock | x 23 (15 x 10mm) |
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
Components List
- Part 1: Top Panel (1 pc)
- Part 2: Side Panel (1 pc)
- Part 3: Side Panel (1 pc)
- Part 4: Top Surface (1 pc)
- Part 5: Support Bar (1 pc)
- Part 6: Back Panel (2 pcs)
- Part 7: Back Panel (1 pc)
- Part 8: Support Bar (1 pc)
- Part 9: Leg Bracket (4 pcs)
- Part 10: Drawer Front (3 pcs)
- Part 11: Drawer Side Panel (3 pcs)
- Part 12: Drawer Side Panel (3 pcs)
- Part 13: Drawer Back Panel (3 pcs)
- Part 14: Drawer Bottom Panel (3 pcs)
- Part 15: Drawer Support (3 pcs)
- Part 16: Drawer Runner (2 pcs)
- Part 17: Drawer Runner (3 pcs)
Exploded View
An exploded view shows all components and their relative positions before assembly.
Assembly Steps
Step 1: Prepare Slide Rails
Separate glide rail (A) into two parts. Fix slide rail (A) into No.2 and No.3 plates using screw (C) as shown.
[Diagram Description: Shows slide rail A being attached to the inner sides of panels 2 and 3 using screws C. Multiple attachment points are indicated.]
Step 2: Attach Top Panel
Insert quickfit screw (D) into corresponding holes in No.1 plate (Top Panel). Fix part (E) using screw (F) as shown.
[Diagram Description: Shows screws D being inserted into panel 1. Part E is then attached to panel 1 using screws F.]
Step 3: Attach Side Panels to Top
Insert quickfit screw (D) into corresponding holes in No.2 and No.3 plates (Side Panels) with a screwdriver.
[Diagram Description: Shows screws D being inserted into panels 2 and 3.]
Step 4: Connect Side Panels
Connect No.2 and No.3 plates with No.5 (Support Bar). Turn cam lock (Q) in No.5 plate clockwise to tighten as shown.
[Diagram Description: Shows panels 2 and 3 being connected by part 5, with cam locks Q securing the connection. A 180-degree turn is indicated for tightening.]
Step 5: Attach Main Frame Components
Attach No.1 plate (Top Panel) to No.2 and No.3 plates using wooden dowel (P) and turn cam lock (Q) in No.2 and No.3 plates clockwise to tighten as shown.
Slide No.6, No.8, and No.7 plates (Back Panels/Supports) into available slots as shown.
[Diagram Description: Shows panel 1 being attached to the structure formed by 2, 3, and 5 using dowels P and cam locks Q. Then, panels 6, 8, and 7 are slid into grooves.]
Step 7: Attach Top Surface
Attach No.4 plate (Top Surface) to No.2 and No.3 plates using wooden dowel (P), and fix with screw (G) as shown.
[Diagram Description: Shows panel 4 being attached to the top of the assembly using dowels P and screws G.]
Step 8: Attach Legs and Drawer Slides
Fix No.9 leg bracket to No.4 plate with screw (F) as shown.
Insert quickfit screw (D) into No.10 plate (Drawer Front) with a screwdriver as shown.
[Diagram Description: Shows leg brackets 9 being attached to panel 4 with screws F. Screws D are inserted into panel 10.]
Step 10: Prepare Drawer Sides
Fix runner (B) into No.11 and No.12 plates (Drawer Side Panels) with screw (C) as shown.
[Diagram Description: Shows drawer runners B being attached to the inner sides of drawer panels 11 and 12 using screws C.]
Step 11: Assemble Drawer Box
Attach No.11, No.12, and No.15 plates (Drawer Side Panels and Support) to No.10 plate (Drawer Front). Turn cam lock (Q) in No.11, 12, and 15 plates clockwise to tighten as shown.
[Diagram Description: Shows drawer panels 11, 12, and 15 being connected to drawer front 10 using cam locks Q.]
Step 12: Insert Drawer Bottom and Back
Slide No.14 plate (Drawer Bottom Panel) into available slots as shown. Attach No.13 plate (Drawer Back Panel) to the component.
[Diagram Description: Shows drawer bottom 14 sliding into grooves on the drawer sides, and drawer back 13 being attached.]
Step 13: Secure Drawer Assembly
Fix No.13 plate (Drawer Back Panel) with No.11, No.12, and No.15 plates using screw (H) as shown.
[Diagram Description: Shows screws H securing the drawer back panel 13 to the drawer side panels 11 and 12, and drawer support 15.]
Step 14: Attach Drawer Handles
Fix handle (J) to No.10 plate (Drawer Front) with screw (K) as shown.
[Diagram Description: Shows handles J being attached to the drawer fronts 10 using screws K.]
Step 15: Reinforce Back Plates
Reinforce back plates using part (L) with screw (M) as shown.
[Diagram Description: Shows parts L being attached to the back of the main chest structure using screws M.]
Step 16: Install Anti-Tipping Device
Install anti-tipping device (G, N) as shown.
[Diagram Description: Shows the anti-tipping hardware (screws G, parts N, and part E) being attached to the top rear of the chest and potentially the wall.]
Step 17 & 18: Insert Drawers
Slide the assembled drawers into the corresponding runners on the main chest unit.
[Diagram Description: Shows the completed drawers being inserted into the chest unit, aligning with the runners.]
Warranty Information
Warranty Claims
There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
Before making a claim, please call for assistance. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
The product must be used in accordance with the instructions provided. For health reasons, returned furniture must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
Failure to follow the furniture instructions will invalidate the warranty. Damage during installation is not covered, but damage during transportation is.
Scope of Responsibility
FUFU&GAGA shall not bear responsibility for misuse, user damage, or loss of parts during installation. Damage and scratches after use are not covered by the warranty.
Warranty Coverage Areas
This warranty relates to all items bought in the US and covers the following areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
Changed Your Mind?
If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
Defective Items
If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call us first.
Damaged Items
If you receive an order with obvious shipping damage, refuse the delivery. If accepted and shipping damage is found later, follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Disposing of packaging material or attempting to return merchandise without contacting the fulfiller may jeopardize your chances of making a claim and may result in no credit for the return.
