FUFU&GAGA Sideboard Assembly Instructions

Introduction and Important Information

IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES! In order to avoid scratching this furniture, it should be assembled on a soft layer, such as a rug.

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months – in order to assure stability throughout the lifespan of the product.

For regular maintenance and cleaning of the product: for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.

Tools Required and Parts List

Tools Required

• Screwdriver (Phillips head)
• Tool for cam locks (provided)

Parts List

Hardware List

Note: Hardware quantities are aggregated from various steps. Total G = 20 (Step 7) + 15 (Step 9) = 35.

Assembly Steps

Step 1: Attach Runners to Side Panels

Attach runners CL and CR to panels 2 (Left Side Panel) and 3 (Right Side Panel). Insert quickfit screws D into panels 2 and 3.

• Hardware: C x 12 (Ø 3 x 12 mm), D x 4 (Ø 6 x 35 mm), CR x 3, CL x 3.
• Panels: 2, 3.

Description: On panel 2, attach runner CL using screws C. On panel 3, attach runner CR using screws C. Then, insert quickfit screws D into the designated holes on panels 2 and 3, aligning them with the runners.

Visual shows runners CL and CR being screwed onto the inner faces of panels 2 and 3 respectively. Close-ups show screws C securing the runners and screws D being inserted into pre-drilled holes.

⚠️ Please pay attention to the holes where the accessories are inserted. Do not use an electric screwdriver.

Step 2: Attach Side Panels to Back Support

Attach panels 4 (Bottom Panel) and 5 (Back Support Rail) to panel 3 (Right Side Panel) using wooden dowels F and cam locks E.

• Hardware: E x 4 (Ø 15 x 9 mm), F x 4 (Ø 6 x 30 mm).
• Panels: 2, 3, 4, 5.

Description: Insert wooden dowels F into the corresponding holes on panel 3. Attach panel 5 (Back Support Rail) and panel 4 (Bottom Panel) to panel 3 using the dowels. Secure them by inserting cam locks E into the larger holes and turning them clockwise with a tool (I) to tighten. Panel 2 (Left Side Panel) is attached in the same manner.

Visual shows panels 4 and 5 being connected to panel 3. Dowels F are inserted, and then cam locks E are used to secure the connection. Panel 2 is then attached similarly. Close-ups show the cam lock mechanism.

⚠️ Ensure cam locks are turned clockwise to tighten.

Step 3: Insert Wooden Dowels and Slide Back Panel

Insert wooden dowels F into panels 2 and 3. Slide panel 6 (Back Panel) into the available slots.

• Hardware: F x 4 (Ø 6 x 30 mm).
• Panels: 2, 3, 6.

Description: Insert wooden dowels F into the designated holes on the rear edges of panels 2 and 3. Carefully slide panel 6 (Back Panel) into the grooves or slots provided on the inner sides of panels 2 and 3.

Visual shows dowels F being inserted into panels 2 and 3. Panel 6 is then shown sliding into place from the back.

⚠️ Insert dowels slightly.

Step 4: Insert Screws into Top Panel

Insert quickfit screws D into panel 1 (Top Panel).

• Hardware: D x 4 (Ø 6 x 35 mm).
• Panel: 1.

Description: Insert quickfit screws D into the pre-drilled holes on the underside of panel 1 (Top Panel). These screws will later connect to the side panels.

Visual shows screws D being inserted into panel 1. A close-up shows the screw insertion.

⚠️ Please pay attention to the holes where the accessories are inserted. Do not use an electric screwdriver or use force to rotate, as it may cause cracks.

Step 5: Attach Top Panel

Attach panel 1 (Top Panel) to panels 2 and 3, then turn cam locks E clockwise to tighten.

• Hardware: E x 4 (Ø 15 x 9 mm).
• Panels: 1, 2, 3.

Description: Align panel 1 (Top Panel) with the top edges of panels 2 and 3, ensuring the pre-inserted screws D engage with the corresponding holes. Insert cam locks E into the larger holes on panels 2 and 3 and turn them clockwise using a tool (I) to secure panel 1.

Visual shows panel 1 being placed on top of the assembled side panels. Close-ups show cam locks E being inserted and tightened.

⚠️ Ensure cam locks are turned clockwise to tighten.

Step 6: Flip and Attach Back Panel

Flip the assembled component 180°. Insert wooden dowels F into panels 3 and 2. Slide panel 6 (Back Panel) into the available slots.

• Hardware: F x 4 (Ø 6 x 30 mm).
• Panels: 2, 3, 6.

Description: Carefully turn the partially assembled unit upside down. Insert wooden dowels F into the designated holes on the rear edges of panels 3 and 2. Slide panel 6 (Back Panel) into the grooves or slots on the inner sides of panels 3 and 2.

Visual shows the unit being flipped. Dowels F are inserted into the side panels, and panel 6 is slid into place.

⚠️ Insert dowels slightly.

Step 7: Attach Base Panel

Attach panel 7 (Base Panel) to panels 2 and 3 using screw G.

• Hardware: G x 4 (Ø 4 x 35 mm).
• Panels: 2, 3, 7.

Description: Position panel 7 (Base Panel) at the bottom of the unit, between panels 2 and 3. Secure it by inserting screws G through the pre-drilled holes on the outer sides of panels 2 and 3 into panel 7.

Visual shows panel 7 being attached to the bottom of the side panels using screws G.

⚠️ Please note: Do not use an electric screwdriver or use excessive force to rotate, as it may cause cracks.

Step 8: Fix Legs

Fix legs 8 to panel 7 (Base Panel) using nails H.

• Hardware: H x 6 (Ø 6 x 30 mm).
• Panel: 7.
• Parts: 8 (Legs).

Description: Attach the three legs (8) to the underside of panel 7 (Base Panel) using nails H. The diagram shows the placement of the legs and the nails.

Visual shows the base of the unit (panel 7) and the three legs (8) being attached with nails (H). A close-up shows the attachment point.

Step 9: Assemble Drawer Boxes

Attach panels 10 (Drawer Left Side) and 11 (Drawer Right Side) to panel 12 (Drawer Bottom Panel) using screw G. Connect panel 13 (Drawer Back Panel) to panel 12 using screw G.

• Hardware: G x 15 (Ø 4 x 35 mm).
• Panels: 10, 11, 12, 13.

Description: For each drawer: Attach drawer sides 10 and 11 to the edges of the drawer bottom panel 12 using screws G. Then, attach the drawer back panel 13 to the rear edge of the drawer bottom panel 12 using screws G. This forms the basic drawer box structure.

Visual shows the assembly of three drawer boxes. Sides 10 and 11 are attached to bottom 12, and back 13 is attached to bottom 12. Screws G are used for all connections.

⚠️ This step is repeated for 3 drawers (x3).

Step 10: Insert Drawer Base Support

Slide panel 14 (Drawer Base Support) into the available slots in panels 10 & 12.

• Panel: 14.
• Parts: 10, 12.

Description: This step describes sliding a support piece (14) into grooves within the assembled drawer sides (10) and bottom (12). This likely provides rigidity to the drawer base.

Visual shows a panel (14) being slid into grooves within the drawer structure.

⚠️ This step is repeated for 3 drawers (x3).

Step 11: Attach Drawer Fronts and Handles

Insert quickfit screw D into panel 9 (Drawer Front). Fix handle K to panel 9 using screw J.

• Hardware: D x 15 (Ø 6 x 35 mm), J x 6 (Ø 3.5 x 14 mm), K x 3 (Handle).
• Panel: 9.

Description: For each drawer front (9): Insert quickfit screws D into the designated holes on the inner side of the drawer front. Attach the handle K to the outer side of the drawer front using screws J.

Visual shows screws D being inserted into the back of drawer front 9. Handles K are then attached to the front using screws J. Close-ups show the screw and handle attachment.

⚠️ Please note: Do not use an electric screwdriver or use force to rotate, as it may cause cracks.

⚠️ This step is repeated for 3 drawers (x3).

Step 12: Attach Drawer Fronts to Drawer Boxes

Attach panel 9 (Drawer Front) to the assembled drawer component (from steps 9-11), then turn cam locks E clockwise to tighten.

• Hardware: E x 15 (Ø 15 x 9 mm).
• Panels: 9, 10, 11, 12.

Description: Align the drawer front (9) with the front of the assembled drawer box (sides 10, 11, bottom 12). Insert cam locks E into the corresponding holes on the drawer sides and turn them clockwise using a tool (I) to secure the drawer front.

Visual shows drawer front 9 being attached to the drawer box. Cam locks E are used for securing.

⚠️ Ensure cam locks are turned clockwise to tighten.

⚠️ This step is repeated for 3 drawers (x3).

Step 13: Attach Drawer Runners to Drawer Sides

Fix runners DR and DL to panels 11 & 10 (Drawer Sides) using screw C.

• Hardware: C x 12 (Ø 3 x 12 mm), DR x 3, DL x 3.
• Panels: 10, 11.

Description: Attach the drawer runners (DR and DL) to the outer sides of the drawer boxes (panels 10 and 11) using screws C. Ensure they are correctly oriented to slide into the runners on the main sideboard frame.

Visual shows drawer runners DR and DL being attached to the sides of the drawer boxes using screws C.

⚠️ Please pay attention to the holes where the accessories are inserted.

⚠️ This step is repeated for 3 drawers (x3).

Step 14: Install Anti-Tipping Device (Optional)

If you want to stabilize the unit, you could choose to install the anti-tipping device as shown.

• Hardware: G x 1 (Ø 4 x 35 mm), N x 1 (Ø 4 x 14 mm), O x 1, P x 1 (Ø 6 x 30 mm).
• Panel: 1 (Main unit).

Description: This step describes the installation of an anti-tipping safety device. It involves attaching components (N, O, P, G) to the back of the sideboard and to the wall (not shown in detail) to prevent it from falling over.

Visual shows the main sideboard unit. It illustrates attaching strap components (N, O, P) to the unit using screw G. A separate diagram shows a bracket and screw assembly, implying wall attachment.

Note: The anti-tipping device is crucial for safety, especially in households with children or pets.

Warranty and Returns

Warranty

• Warranty Claims: There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty starts from the date of purchase, which must be verified by proof of purchase.
• Support: For further information or queries, visit feedbackstation@163.com. The After-sale Team aims to respond within 48 hours. Provide your purchase order number and details of the problem when requesting a replacement part. If a part is out of stock, a shipping date will be provided.
• Product Usage: The product must be used in accordance with the instructions provided for health reasons.
• Returns: If the furniture needs to be returned for other reasons, it must be cleaned, dried, and returned within 30 days of receipt.
• Type of Warranty Claim: Failure to follow furniture instructions will invalidate the warranty. Damage during installation is not covered, but damage during transportation is.
• Scope of Responsibility: FUFU&GAGA shall not bear responsibility for misuse, user damage, or loss of parts during installation. Damage and scratches after use are not covered by the warranty.
• Warranty Coverage Areas (US): Sheet parts: 1 month from the date of purchase. Electrical parts: 1 month from the date of purchase.

Returns

Changed Your Mind and Need to Return Your Item?

If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

Defective Items

If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please consult our FAQ section at feedbackstation@163.com as there may be a simple solution to the issue.

Damaged Items

If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.

In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.