FUFU&GAGA Dresser Assembly Instructions

Important Information

IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment provided. If not included with this product, please purchase a wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

For regular maintenance and cleaning of the product: for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools and Parts

Please prepare the following tools:

Tape Measure
Screwdriver (Phillips head)
Hammer
Level
Wrench

When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.

Parts List:

A: x42 (Ø6 x 35 mm)
B: x42 (Ø4 x 25 mm)
C: x12 (Ø4 x 30 mm)
D: x46 (Ø4 x 12 mm)
E: x20 (4 x 30 mm)
F: x62 (3 x 12 mm)
G: x40 (6 x 30 mm)
H: x5 (4 x 30 mm)
J: x6 (3 x 16 mm)
K: x1 (4 x 40 mm)
CL: x6 (3 x 12 mm)
CR: x6 (3 x 16 mm)
DL: x6 (3 x 16 mm)
DR: x6 (3 x 16 mm)
L: x8 (3 x 12 mm)
M: x2 (3 x 12 mm)
N: x8 (3 x 16 mm)
P: x2 (4 x 40 mm)
Q: x2 (4 x 40 mm)

Assembly Steps

Step 1

Parts Used: A (x3), B (x3), C (x6), F (x6), G (x8), CL (x3)

Insert quickfit screw(A) and wooden dowel(G) into plate 6 at first, then attach to plate 3.

Put cam lock(B) into holes in plate 3 and turn clockwise to tighten as shown.

Insert wooden dowel(G) into plate 3, then attach plate 5 and fix with screw(C) as shown.

Fix slide rail(CL) to plate 5 with screw(F) as shown.

Diagram Description: Shows assembly of the base frame, connecting side panels and bottom panels using screws, dowels, and cam locks. Slide rails are attached to the side panels.

Step 2

Parts Used: A (x3), B (x3), C (x6), F (x6), G (x8), CR (x3)

Insert quickfit screw(A) and wooden dowel(G) into plate 6 at first, then attach to plate 4.

Put cam lock(B) into holes in plate 4 and turn clockwise to tighten as shown.

Insert wooden dowel(G) into plate 4, then attach plate 5 and fix with screw(C) as shown.

Fix slide rail(CR) to plate 5 with screw(F) as shown.

Diagram Description: Similar to Step 1, but connecting plates 6 and 4, and attaching slide rails CR to plate 5.

Step 3

Parts Used: F (x12), CL (x3), CR (x3)

Fix slide rail(CL) to plate 16 with screw(F) as shown.

Flip the plate, fix slide rail(CR) with screw(F) as shown.

Diagram Description: Shows attaching slide rails CL and CR to a central support plate (plate 16) using screws F.

Step 4

Parts Used: A (x6), B (x6), G (x6)

Insert quickfit screw(A) and wooden dowel(G) into plate 1 at first, then cover to plate 3, 16 and 4.

Put cam lock(B) into holes in plate 3, 4, 16 and turn clockwise to tighten as shown.

Diagram Description: Shows attaching the top panel (plate 1) to the assembled side and back panels (3, 16, 4) using screws A, dowels G, and cam locks B.

Step 5

Parts Used: D (x6), G (x6)

Slide back plates 7 and 17 along grooves as shown.

Insert wooden dowel(G) into plate 2, then attach to plate 3, 16 and 4, fix with screw(D) as shown.

Diagram Description: Shows sliding thin back panels (7, 17) into grooves on the frame. Then, attaching a horizontal support (plate 2) to the side and back panels using dowels G and screws D.

Step 6

Parts Used: D (x10), E (x20), H (x5), K (x1)

Fix iron sheet(H) to leg 8 and leg support 15 with screw(D) as shown.

Rotate part(K) into leg support.

Fix leg to plate 2 with screw(E) as shown.

Diagram Description: Shows attaching metal brackets (H) to the bottom of the dresser frame (legs 8 and support 15) using screws D. A part K is inserted into a leg support. Legs are then attached to the base using screws E.

Step 7

Parts Used: A (x30), B (x30), D (x30), G (x12)

Insert quickfit screw(A) and wooden dowel(G) into plate 9 at first, then attach plate 12, 13 and 14.

Put cam lock(B) into holes in plate 12, 13, 14 and turn clockwise to tighten as shown.

Fix plate 11 to plate 14, 12 and 13 with screw(D) as shown.

Diagram Description: Shows the assembly of drawer components. Plates 9, 12, 13, 14 are connected using screws A, dowels G, and cam locks B. Plate 11 is then attached using screws D. This step is repeated six times for the drawers.

Step 8

Parts Used: F (x36), DL (x6), DR (x6), J (x6)

Fix runner(DL) and (DR) to plate 12 and 13 respectively with screw(F) as shown.

Fix handle(J) to plate 9 with screw(F) as shown.

Diagram Description: Shows attaching drawer runners (DL, DR) to the sides of the drawer boxes (plates 12, 13) using screws F. Drawer handles (J) are attached to the drawer fronts (plate 9) using screws F. This step is repeated six times for the drawers.

Step 9

Parts Used: F (x2), L (x8), N (x8), M (x2)

Align rails, slide all drawers.

Reinforce back plate using part(L) with screw(N) as shown.

Fix strip(M) to back of plate 1 with screw(F) as shown.

Diagram Description: Shows sliding the assembled drawers into the dresser frame. Reinforcement parts (L) are attached to the back panels using screws N. A strip (M) is attached to the top back panel (plate 1) using screws F.

Step 10: Install Anti-Tipping Device

Parts Used: P (x2), Q (x2)

Install anti-tipping device as shown.

Diagram Description: Shows how to attach the anti-tipping hardware to the wall and the top rear of the dresser to prevent it from tipping over.

Warranty Information

WARRANTY CLAIMS

There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
Before making a claim, contact FUFU&GAGA for assistance. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. FUFU&GAGA will arrange within 48 hours. If there is out of stock, they will reply with a shipping date.
The product must be used in accordance with the instructions provided. For health reasons.
For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

Failure to follow the furniture instructions will invalidate the warranty.
Does not include damage during installation, but includes damage during transportation.

Scope of Responsibility

FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
After use, damage and scratches of the furniture are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas:

Sheet parts: 1 month from the date of purchase.
Electrical parts: 1 month from the date of purchase.

Returns

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM? PLEASE FOLLOW THE BELOW INSTRUCTIONS:

If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

If your item is defective in any way, i.e., it doesn't work but you can't identify why, in the first instance, please contact FUFU&GAGA.

DAMAGED ITEMS

If you receive an order with obvious shipping damage from the retailer, then it is suggested the delivery is refused.
If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfillment center, you jeopardize your chances of making a claim, and you may not receive a credit for the return.

	FUFU&GAGA Dresser Assembly Instructions and Product Information Step-by-step assembly guide for the FUFU&GAGA dresser, including parts list, safety warnings, anti-tipping instructions, warranty, and returns policy.
	FUFU&GAGA KF200252-01+02 White 9-Drawer Double Dresser Assembly Instructions Comprehensive assembly guide for the FUFU&GAGA KF200252-01+02 White 9-Drawer Double Dresser, including important safety information, parts list, and step-by-step instructions for assembly and care.
	FUFU&GAGA Chest Assembly Instructions and Warranty Comprehensive guide for assembling the FUFU&GAGA Chest (Model LJY-KF020282-01), including a detailed parts list, step-by-step instructions, safety warnings, and warranty information.
	FUFU&GAGA Dresser Assembly Instructions Comprehensive assembly instructions for the FUFU&GAGA Dresser, including parts list, step-by-step guidance, safety warnings, and warranty information.
	FUFU&GAGA Sideboard Assembly Instructions and User Manual Detailed assembly guide and user manual for the FUFU&GAGA Sideboard, including parts list, step-by-step instructions, warranty, and returns information.
	Installation Manual for FUFU&GAGA 63" W 12-Drawer Dresser Comprehensive installation guide for the FUFU&GAGA 63" W 12-Drawer Dresser (Model KF210251-01), including safety warnings, parts list, assembly steps, and warranty information.
	FUFU&GAGA KF150167-01 Assembly Instructions and Product Manual Comprehensive assembly guide for the FUFU&GAGA KF150167-01 furniture, featuring detailed steps, parts list, hardware identification, safety warnings, and warranty information.
	FUFU&GAGA Chest Assembly Instructions and Product Information Comprehensive guide for assembling the FUFU&GAGA Chest (3-Drawer). Includes safety warnings, parts list, required tools, step-by-step assembly instructions, and warranty/returns information.