Sideboard Assembly Instructions

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Assembly Tips

Avoid Scratches

To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

Improve Efficiency

Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Topple Warning

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

Important Maintenance

It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe it fully, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.

Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools and Parts Identification

When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

Hardware

• A: ⌀6 x 35 mm (x16 +1)
• B: ⌀8 x 30 mm (x15 +1)
• C: ⌀15 x 10 mm (x16 +1)
• D: ⌀4 x 35 mm (x2)
• E: (x1)
• F: (x4)
• G: (x4)
• H: ⌀4 x 12 mm (x48 +1)
• J: (x4)
• K: ⌀4 x 16 mm (x4)
• L: (x16)
• M: (x2)

Main Parts

• 1: Top Panel (1PC)
• 2: Left Side Panel (1PC)
• 3: Right Side Panel (1PC)
• 4: Door Panel (4PCS)
• 5: Middle Shelf/Divider (1PC)
• 6: Back Panel (2PCS)
• 7: Adjustable Shelf (4PCS)
• 8: Bottom Panel (1PC)
• 9: Support Bar/Base (1PC)
• 10: Leg Support (1PC)

Assembly Steps

Step 1

Insert quickfit screw (A, ⌀6 x 35 mm) into corresponding holes in board 9 (Support Bar/Base) with a screwdriver ?.

Step 2

Attach board 9 to board 8 (Bottom Panel) using wooden dowel (B, ⌀8 x 30 mm) and turn cam lock (C, ⌀15 x 10 mm) clockwise ? to tighten.

Step 3

Insert quickfit screw (A, ⌀6 x 35 mm) into corresponding holes in boards 2 (Left Side Panel) and 3 (Right Side Panel) with a screwdriver ?.

Step 4

Connect boards 2 and 3 to board 8 (Bottom Panel) and board 9 (Support Bar/Base) using wooden dowels (B, ⌀8 x 30 mm) and turn cam locks (C, ⌀15 x 10 mm) clockwise ? to tighten.

Step 5

Fix board 5 (Middle Shelf/Divider) to board 8 (Bottom Panel) using wooden dowel (B, ⌀8 x 30 mm) and then fix with screw (D, ⌀4 x 35 mm) as shown. Pay attention to the holes where the accessories are inserted.

Step 6

Rotate foot peg (E) into leg support 10 at first. Rotate leg support 10 into board 8 (Bottom Panel) as shown.

Step 7

Insert quickfit screw (A, ⌀6 x 35 mm) into corresponding holes in board 1 (Top Panel) with a screwdriver ?.

Step 8

Slide board 6 (Back Panel) into available slots as shown.

Step 9

Cover board 1 (Top Panel) to the assembled component using wooden dowels (B, ⌀8 x 30 mm) and turn cam locks (C, ⌀15 x 10 mm) clockwise ? to tighten as shown.

Step 10

Insert part (L) into corresponding holes in boards 2, 5, and 3, and then put board 7 (Adjustable Shelf) in as shown.

Step 11

Fix hinge (F) to board 4 (Door Panel, x2) with screw (H, ⌀4 x 12 mm) as shown. Fix hinge (G) to another board 4 (Door Panel, x2) with screw (H, ⌀4 x 12 mm) as shown. Fix knob (J) with screw (K, ⌀4 x 16 mm).

Note: Do not use an electric screwdriver or use excessive force to rotate, as it may cause cracks.

Step 12

Attach board 4 (Door Panel, x2) to board 5 (Middle Shelf/Divider) by fixing hinge (G) with screw (H, ⌀4 x 12 mm) as shown.

Note: Please don't use an electric screwdriver or use force to rotate, may cause crack.

Step 13

Attach another board 4 (Door Panel, x2) to board 2 (Left Side Panel) and 3 (Right Side Panel) by fixing hinge (F) with screw (H, ⌀4 x 12 mm) as shown.

Note: Please don't use an electric screwdriver or use force to rotate, may cause crack.

Step 14

Hinge adjustment guide. The diagrams show adjustments for door alignment (up/down, left/right, in/out) using the hinges.

Step 15

Install anti-tipping device as shown using screws (M).

Warranty Information

Warranty Claims

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty starts from the date of purchase, verified by proof of purchase.
• Before making a claim, contact FUFU&GAGA for assistance. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
• The product must be used according to the provided instructions for health reasons.
• If the furniture needs to be returned for other reasons, it must be cleaned, dried, and returned within 30 days of receipt.

Type of Warranty Claim

• Failure to follow furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is.

Scope of Responsibility

• FUFU&GAGA shall not bear responsibility for misuse, user damage, or loss of parts during installation.
• Damage and scratches after use are not covered by the warranty.

Warranty Coverage Areas (The US)

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

Changed Your Mind?

If you have purchased and changed your mind, follow the retailer's instructions for returns.

Defective Items

If your item is defective, contact FUFU&GAGA for assistance in identifying the issue.

Damaged Items

• If you receive an order with obvious shipping damage from the retailer, refuse the delivery.
• If delivery has been accepted and shipping damage is found, follow specific instructions advised by the retailer.

In all circumstances, save all packaging material and paperwork for the order. Disposing of packaging material or attempting to return merchandise without contacting the fulfiller may jeopardize your chances of making a claim and receiving credit.