Important Information
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
For regular maintenance and cleaning of the product: For the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
Tools and Parts
Please prepare the following tools:
Diagram shows various hand tools including screwdrivers (Phillips and flathead), an Allen key, a hammer, and a measuring tape.
When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.
- A
- x 48 (Ø 6 x 35 mm)
- B
- x 64 (Ø 15 x 9 mm)
- C
- x 10 (Ø 6 x 30 mm)
- D
- x 48 (Ø 3 x 14 mm)
- E
- x 30 (Ø 4 x 30 mm)
- F
- x 8 (Ø 7 x 85 mm)
- G
- x 22 (Ø 3 x 12 mm)
- H
- x 16 (Ø 6 x 12 mm)
- I
- x 1 (Ø 4 x 14 mm)
- J
- x 5 (Sizes vary: 4 x 14 mm, 4 x 40 mm)
- K
- x 4 (Ø 6 x 50 mm)
- CR
- x 6 (300 mm)
- CL
- x 6 (300 mm)
- DR
- x 6 (300 mm)
- DL
- x 6 (300 mm)
- L
- x 2 (Ø 4 x 14 mm)
- M
- x 1 (Ø 4 x 40 mm)
- N
- x 3 (Ø 4 x 40 mm)
- O
- x 1 (No size specified)
Assembly Steps
Step 1
Fix slide rail (CR) to board 5 with screw (D) as shown. Please do not use an electric screwdriver or excessive force to rotate, as this may cause cracking.
Diagram shows screw (D) attaching slide rail (CR) to board 5. A close-up shows the screw insertion. Then, quickfit screw (A) is inserted into corresponding holes in board 5.
Step 2
Fix slide rail (CL) to another side of board 5 with screw (D) as shown. Please do not use an electric screwdriver or excessive force to rotate, as this may cause cracking.
Diagram shows screw (D) attaching slide rail (CL) to board 5. A close-up shows the screw insertion. Then, quickfit screw (A) is inserted into corresponding holes in board 5.
Step 3
Insert quickfit screw (A) into boards 2 and 3 as shown. Please pay attention to the holes where the accessories are inserted.
Diagram shows quickfit screws (A) being inserted into pre-drilled holes on boards 2 and 3.
Step 4
Attach board 3 to planks 6, 8, 10 with short wooden dowel (C) and turn cam locks (B) clockwise to tighten as shown. Attach board 5 to planks 6, 8, 10 with long wooden dowel (K) and turn cam locks (B) clockwise to tighten as shown. Please note that long wooden dowel (K) needs to pass through board 5.
Diagram shows board 3 being attached to planks 6, 8, 10 using dowels (C) and cam locks (B). Board 5 is shown being attached to planks 6, 8, 10 using dowels (K) and cam locks (B), with dowel (K) passing through board 5.
Step 5
Connect planks 6, 8, 10 with another side of board 5 and turn cam locks (B) clockwise to tighten as shown. Attach board 2 to planks 6, 8, 10 with short wooden dowel (C) and turn cam locks (B) clockwise to tighten as shown.
Diagram shows planks 6, 8, 10 being connected to board 5 using cam locks (B). Board 2 is then attached to planks 6, 8, 10 using dowels (C) and cam locks (B).
Step 6
Insert quickfit screw (A) into board 1 with screwdriver as shown.
Diagram shows quickfit screw (A) being inserted into board 1.
Step 7
Insert screw (F) into boards 2 and 3 at first, then turn 90°. Cover board 1 to the component with screw (F), and turn cam locks (B) clockwise to tighten as shown.
Diagram shows screws (F) inserted into boards 2 and 3. Board 1 is then placed on top and secured with screws (F) and cam locks (B).
Step 8
Insert screw (F) into boards 2 and 3 at first, then turn 90°. Attach board 4 to the component with screw (F) and wooden dowel (C), turn cam locks (B) clockwise to tighten as shown.
Diagram shows screws (F) inserted into boards 2 and 3. Board 4 is then attached using screws (F), dowels (C), and cam locks (B).
Step 9
Fix board 4 to board 5 with screw (N) as shown.
Diagram shows screw (N) being used to attach board 4 to board 5.
Step 10
Fix back board 9 to boards 1, 2, 3, 4, 5 with screw (G) as shown.
Diagram shows back board 9 being attached to the main structure using multiple screws (G).
Step 11
Fix leg 7 to the bottom of board 4 with screw (H). Fix leg support 11 to board 4 with screw (J) as shown.
Diagram shows legs (7) being attached to the bottom of board 4 using screws (H). Leg supports (11) are attached to board 4 using screws (J).
Step 12
Fix slide rail (CL) and (CR) to boards 2 and 3 respectively with screw (D) as shown.
Diagram shows slide rails (CL) and (CR) being attached to boards 2 and 3 using screws (D).
Step 13
Attach board 12, 13, 15 to board 14 with screw (E). Slide board 16 into available slots as shown. (Repeat for 6 drawers).
Diagram shows boards 12, 13, 15 being attached to board 14 with screws (E). Board 16 is shown sliding into slots. This assembly forms part of a drawer.
Step 14
Insert quickfit screw (A) into board 17 with screwdriver as shown. Attach board 17 to the component and turn cam locks (B) clockwise to tighten as shown. (Repeat for 3 drawers).
Diagram shows quickfit screws (A) inserted into board 17. Board 17 is then attached to a drawer component using cam locks (B).
Step 15
Insert quickfit screw (A) into board 18 with screwdriver as shown. Attach board 18 to the component and turn cam locks (B) clockwise to tighten as shown. (Repeat for 3 drawers).
Diagram shows quickfit screws (A) inserted into board 18. Board 18 is then attached to a drawer component using cam locks (B).
Step 16
Fix runner (DR) and (DL) to board 13 and 12 respectively with screw (D) as shown. (Repeat for 3 drawers).
Diagram shows runners (DR) and (DL) being attached to boards 13 and 12 using screws (D).
Step 17
Align rails and insert all drawers.
Diagram shows the sideboard frame with drawers being inserted into their respective slots.
Step 18
Install anti-dumping device as shown.
Diagram shows the components (J, L, M, N, O) for the anti-dumping device and how they are attached to the sideboard and the wall.
Warranty
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please call for assistance. Provide your purchase order number and details of the problem for a replacement part. Replacements will be arranged within 48 hours. If out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
- FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- After use, damage and scratches to the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The Us and Covers The Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer’s instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e., it doesn’t work but you can’t identify why, please call us in the first instance.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order.
- Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.
