Sideboard
Version: 09/01/2023
Important Information & Safety
❓ IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
[scratch icon] AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
[people icon] IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
❗ ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
❗ IMPORTANT! It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the product's lifespan.
For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe fully, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools and Parts
[screwdriver icon] [drill icon] [pencil icon] [allen key icon] Please prepare the following tools.
❗ When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
Hardware List (A-U)
| Part | Quantity | Dimensions |
|---|---|---|
| A | 24 | Ø6x35mm |
| B | 20 | Ø14x11mm |
| C | 4 | Ø14x9mm |
| D | 20 | Ø6x30mm |
| E | 2 | 300mm |
| F | 38 | Ø4x16mm |
| G | 1 | [length not specified] |
| H | 14 | M4x30mm |
| J | 4 | Ø4x16mm |
| K | 1 | [type not specified] |
| L | 4 | Ø3.5x14mm |
| M | 2 | [type not specified] |
| N | 2 | [type not specified] |
| P | 8 | [type not specified] |
| Q | 4 | [type not specified] |
| R | 6 | Ø4x30mm |
| S | 3 | [type not specified] |
| T | 2 | [type not specified] |
| U | 2 | [type not specified] |
Component List (1-20)
- 1: Top Panel [image description: A rectangular panel]
- 2: Bottom Panel [image description: A rectangular panel]
- 3: Left Side Panel [image description: A rectangular panel]
- 4: Middle Divider Panel [image description: A rectangular panel]
- 5: Right Side Panel [image description: A rectangular panel]
- 6: Back Panel (Right) [image description: A rectangular panel]
- 7: Shelf [image description: A rectangular panel]
- 8: Middle Support Panel [image description: A rectangular panel]
- 9: Back Panel (Left) [image description: A rectangular panel]
- 10: Back Panel (Center) [image description: A rectangular panel]
- 11: Door Panel (Left) [image description: A rectangular panel]
- 12: Door Panel (Right) [image description: A rectangular panel]
- 13: Drawer Front Panel [image description: A rectangular panel]
- 14: Drawer Side Panel (Left) [image description: A rectangular panel]
- 15: Drawer Side Panel (Right) [image description: A rectangular panel]
- 16: Drawer Bottom Panel [image description: A rectangular panel]
- 17: Drawer Back Panel [image description: A rectangular panel]
- 18: Leg Support Frame [image description: A frame structure]
- 19: Steel Tube [image description: A long, thin tube]
- 20: Leg Support [image description: A small support piece]
This product has reserved holes. Please install hardware components in the correct reserved holes according to the figure and written instructions. Do not drill holes by yourself.
Assembly Steps
Step 1
Parts Used: A x 4, E x 2, F x 4
Dimensions: Ø6x35mm, 300mm, Ø4x16mm
Separate the glide into two parts. Fix slide rail (E) to plate 4 and plate 5 using screw (F) as shown. Insert quickfit screw (A) into corresponding holes in plate 4 and 5 with a screwdriver as shown.
[Diagram description: Shows slide rails (E) being attached to the sides of plates 4 and 5 using screws (F). Quickfit screws (A) are then inserted into pre-drilled holes on plates 4 and 5.]
Step 2
Parts Used: B x 4, D x 4
Dimensions: Ø14x11mm, Ø6x30mm
Connect plate 4 and 5 with plate 8 using wooden dowel (D). Put cam lock (B) into holes in plate 8 and turn clockwise to tighten as shown.
[Diagram description: Shows plates 4 and 5 being joined to plate 8 using dowels (D) and cam locks (B). Cam locks are turned clockwise to secure.]
Step 3
Parts Used: A x 8
Dimensions: Ø6x35mm
Insert quickfit screw (A) into corresponding holes in plate 2 with a screwdriver as shown.
[Diagram description: Shows screws (A) being inserted into plate 2.]
Step 4
Parts Used: B x 8, D x 8
Dimensions: Ø14x11mm, Ø6x30mm
Attach plate 2 to plates 3, 4, 5, and 6 using wooden dowel (D). Put cam lock (B) into holes in plates 3, 4, 5, 6 and turn clockwise to tighten as shown.
[Diagram description: Shows plate 2 being attached to the assembly of plates 3, 4, 5, and 6 using dowels (D) and cam locks (B). Cam locks are turned clockwise.]
Step 5
Parts Used: G x 1, H x 4
Dimensions: M6x30mm
Fix part 18 (Leg Support Frame) with steel tube 19 together using screw (H) as shown.
[Diagram description: Shows leg support frames (18) being connected by steel tubes (19) using screws (H). Part G is also shown.]
Step 6
Parts Used: G x 1, H x 10
Dimensions: M6x30mm
Attach the component (assembled leg structure) to plate 2 using screw (H) as shown.
[Diagram description: Shows the leg assembly being attached to plate 2 using screws (H). Part G is also shown.]
Step 7
Parts Used: J x 4, K x 1
Dimensions: Ø4x16mm
Fix leg support 20 to plate 2 using screw (J) as shown.
[Diagram description: Shows leg supports (20) being attached to plate 2 using screws (J). Part K is also shown.]
Step 8
Parts Used: A x 8, L x 4, M x 2
Dimensions: Ø6x35mm, Ø3.5x14mm
Insert quickfit screw (A) into corresponding holes in plate 1 (Top Panel) as shown. Fix part (M) to plate 1 using screw (L) as shown.
[Diagram description: Shows screws (A) being inserted into plate 1. Part M is then attached to plate 1 using screws (L).]
Step 9
[Diagram description: Shows panel 10 being folded and attached to another panel, likely part of the drawer or back assembly.]
Step 10
Parts Used: B x 8, D x 8
Dimensions: Ø14x11mm, Ø6x30mm
Slide back plates 9 and 10 along grooves as shown. Cover plate 1 (Top Panel) to the top with wooden dowel (D), put cam lock (B) into holes in plates 3, 4, 5, 6 and turn clockwise to tighten as shown.
[Diagram description: Shows back panels (9, 10) sliding into grooves. Plate 1 is placed on top, secured with dowels (D) and cam locks (B) inserted into plates 3, 4, 5, and 6. Cam locks are turned clockwise.]
Step 11
Parts Used: P x 8
Insert part (P) into corresponding holes, then place shelf 7 in as shown.
[Diagram description: Shows part P being inserted into holes on the side panels, and shelf 7 being placed into position.]
Step 12
Parts Used: F x 12, L x 4, N x 2, Q x 4, S x 2
Dimensions: Ø4x16mm, Ø3.5x14mm
Fix hinge (Q) to plate 11 (Left Door) and 12 (Right Door) respectively using screw (F) as shown. Fix handle (S) to door plates using screw (F). Fix part (N) to plate 11 and 12 using screw (L) as shown.
[Diagram description: Shows hinges (Q) being attached to doors (11, 12) with screws (F). Handles (S) are attached to the doors with screws (F). Part N is attached to doors (11, 12) with screws (L).]
Step 13
Parts Used: F x 16
Dimensions: Ø4x16mm
Attach door plate (11, 12) to the unit by fixing hinge using screw (F) as shown.
[Diagram description: Shows the assembled doors (11, 12) being attached to the main unit via their hinges using screws (F).]
Step 14
Parts Used: R x 4
Dimensions: Ø4x30mm
Fix plate 14 and 15 to plate 16 using screw (R) as shown.
[Diagram description: Shows plates 14 and 15 being attached to plate 16 using screws (R). This forms part of the drawer assembly.]
Step 15
Parts Used: A x 4, C x 4, E x 2, F x 6, S x 1
Dimensions: Ø6x35mm, Ø14x9mm, 300mm, Ø4x16mm
Insert quickfit screw (A) into plate 13 (Drawer Front Panel) as shown. Slide plate 17 (Drawer Back Panel) along grooves, then attach plate 13, put cam lock (B) into holes in plate 14, 15 and turn clockwise to tighten as shown. Fix runner (E) to plate 14 and 15 using screw (F) as shown. Fix handle (S) to drawer face plate using screw (F) as shown.
[Diagram description: Shows screws (A) in drawer front (13). Drawer back (17) slides in. Drawer front (13) attaches to drawer sides (14, 15) with cam locks (B). Runners (E) are attached to drawer sides (14, 15) with screws (F). Handle (S) is attached to drawer front (13) with screw (F).]
Step 16
[Diagram description: Shows drawer runners being aligned and the assembled drawer being slid into the sideboard.]
Align rails, slide the drawer.
Step 17
Parts Used: F x 2, T x 2
Dimensions: Ø4x16mm
Fix part (T) to back plate using screw (F) as shown.
[Diagram description: Shows part T being attached to the back panel of the sideboard using screws (F).]
Step 18: Install Anti-Tipping Device
Parts Used: R x 2, U x 2
Dimensions: Ø4x30mm
Install the anti-tipping device by attaching bracket (U) to the top rear of the sideboard using screw (R). Secure the other end of the bracket to the wall using appropriate hardware (not specified, consult wall type). Ensure the sideboard is stable and secured to prevent tipping.
[Diagram description: Shows the sideboard positioned near a wall. Brackets (U) are attached to the top back edge of the sideboard with screws (R). The other end of the bracket is shown being attached to the wall with a screw (R) and wall plug (implied).]
Step 19: Hinge Adjustment
Detailed instructions for adjusting cabinet hinges to ensure proper door alignment and gap. This involves rotating specific screws on the hinge mechanism to adjust the door's position relative to the frame.
Mode 1: Adjust the gap between the overall door frame and the upper and lower sections by rotating screws counterclockwise and then clockwise.
Mode 2: Adjust the gap between the whole door frame and the cabinet (front and back) by rotating screws counterclockwise and then clockwise.
Mode 3: Adjust the corresponding part of the rear door frame left or right by rotating screws in the middle of the hinge counterclockwise or clockwise, respectively.
Warranty Information
Warranty Claims
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please contact FUFU&GAGA. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
- FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- After use, damage and scratches of the furniture are not covered by the warranty.
Warranty Coverage Areas (US)
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
Changed Your Mind?
- If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
Defective Items
- If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call FUFU&GAGA first.
Damaged Items
- If you receive an order with obvious shipping damage from the retailer, refuse the delivery.
- If the delivery has been accepted and shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.
