FSP A06-XE2 Series AC-DC Converter
Product Type: AC-DC Converter
Brand: FSP
Wattage: 6W
Description
The FSP A06-XE2 Series comprises AC-DC switching power supplies housed in a compact package measuring 40.0 x 33.5 x 22.0 mm, capable of delivering 6 watts. These converters are designed for industrial control applications, including AC motor control.
Features
- Universal input voltage range: 90~264VAC at 47~63Hz
- High efficiency up to 80%
- Continuous short circuit protection
- Overload protection
- Over voltage protection
- Low standby power consumption: maximum 0.05W
- High isolation voltage: 3750 VAC
Product Image
A compact, black, rectangular AC-DC converter module with a single output terminal block visible on the front.
Selection Guide
| Part Number | Input Voltage | Output Voltage | Output Current @ Full Load | Efficiency (typ.) | Capacitive Load (max.) |
|---|---|---|---|---|---|
| A06-XE2-3.3 | 90-264 Vac | 3.3Vdc | 1500mA | 70% | 15000uF |
| A06-XE2-05 | 5Vdc | 1200mA | 75% | 6800uF | |
| A06-XE2-12 | 12Vdc | 500mA | 79% | 2500uF | |
| A06-XE2-24 | 24Vdc | 250mA | 80% | 1400uF |
Notes:
- (1) Efficiency measured at full load at 115Vac/60Hz and 230Vac/50Hz after warm-up.
- (2) Capacitive load measured at full load at 115Vac/60Hz, Ta=25°C with constant resistant mode.
- Product information and specifications are subject to change without prior notice.
- All specifications are valid at nominal input voltage (115/230VAC), full load, and 25°C after warm-up time, unless otherwise stated.
Specifications
| Parameter | Conditions | Min. | Typ. | Max. | Unit |
|---|---|---|---|---|---|
| Input | Input voltage range | 90 | 264 | VAC | |
| Input frequency | 47 | 63 | Hz | ||
| Inrush current (cold start @25°C) 115VAC | 20 | A | |||
| Inrush current (cold start @25°C) 230VAC | 40 | A | |||
| Start-up time | 1 | S | |||
| No load power consumption | 0.05 | W | |||
| External fuse (or internal) | Internal wire wound resistor | ||||
| Output | Output voltage accuracy | ±6 | % | ||
| Line regulation (LL-HL at full load) | ±1.25 | % | |||
| Load regulation (10%~100% load) | ±2 | % | |||
| Ripple & noise (1) | 100 | 130 | mVp-p | ||
| Operating frequency | 80 | KHz | |||
| Minimum load | 0 | % | |||
| Environment | Hold up time (115VAC) | 8 | ms | ||
| Hold up time (230VAC) | 72 | ms | |||
| Leakage current (264VAC) | 0.25 | mA | |||
| Operating temperature | With derating | -25 | 85 | °C | |
| Storage temperature | -25 | 85 | °C | ||
| Relative Humidity | 95 | %RH | |||
| Vibration | 1 minute, Pri to Sec cut-off current: 5mA | ||||
| Isolation | Isolation voltage | 3750 | VAC | ||
| Isolation capacitance (DC 500V) | 1100 | pF | |||
| Isolation resistance (115VAC @25°C) | 1 | GΩ | |||
| MTBF (MIL-HDBK-217F) | 1800 | KHours | |||
| Function | Short circuit protection | Continuous, Automatic recovery | |||
| Over load protection | Automatic recovery | ||||
| Over voltage protection | Zener diode clamp | ||||
| Safety | Meet 60950/60335-1 | ||||
| Physical | Potting material | Copolyamide | |||
| Dimension (L x W x H) | 40.0 x 33.5 x 22.0 | mm | |||
| Weight | 38.0 | g | |||
| EMC | EMI (EN 55032) | Class B | |||
| ESD (IEC61000-4-2) | Criteria A | ||||
| EFT (IEC61000-4-4) | Criteria A | ||||
| Surge (IEC61000-4-5) | Criteria A | ||||
Ripple & Noise Test Setup
The Ripple & Noise measurement is conducted using an E-Cap 47uF low ESR and a 0.1uF MLCC connected across the outputs, with a measurement bandwidth of 20MHz.
Schematic illustrating the test setup for Ripple & Noise measurement, showing input voltage (Vin), output voltage (Vout), ground lead, and parallel capacitors (47uF and 0.1uF) connected across the output.
Derating Curve
A graph illustrating the derating curve for the AC-DC converter, showing the relationship between output load percentage (Y-axis) and ambient temperature in degrees Celsius (X-axis). The curve indicates that the converter can operate at 100% load up to approximately 60°C and derates thereafter.
Mechanical Specifications
Detailed dimension drawings of the AC-DC converter module from multiple angles (top, side, bottom), indicating lengths, widths, and heights, along with pin assignments for input and output terminals.
| Pin | Description |
|---|---|
| 1 | Vin (N) |
| 2 | Vin (L) |
| 3 | +Vout |
| 4 | -Vout |
Projection: Third angle projection. Unit: mm. Tolerance: ±0.25mm.
Package Information
A diagram showing the packaging dimensions for the AC-DC converter, indicating the size of a tube containing multiple units.
Packaging Details:
- Unit: mm
- 1 Tube contains 14 pcs
- Tube Length: 520±2mm
Safety Standard Approval
Meets standards: 60950 / 60335-1
Environmental Specifications
- Operating temperature: -25°C to +85°C
- Storage temperature: -25°C to +85°C
- Relative Humidity: up to 95% (non-condensing)
Additional Notes
This content is subject to change. Please refer to the specification for more detail. FSP reserves the right to change the content without prior notice.
