FSP PMP250 Series 220-250W Medical Power Supplies Datasheet

DESCRIPTION

The PMP250 series of AC/DC switching power supplies offers 220-250 watts of continuous output power. They are enclosed in a 94V-0 rated polycarbonate case with an IEC320/C14 (Class I) or IEC320/C18 (Class II) inlet for worldwide use. All models meet EN 55011 class B emission limits and are designed for medical applications.

FEATURES

BF class insulation
Operating altitude up to 5000 meters
Efficiency level VI / CoC EPS V5 tier 2 requirements
No load power consumption less than 0.15W
With PFC circuit
Wide input range 80 to 264 VAC
100% burn-in
Overvoltage protection
Overcurrent protection
Compliant with RoHS requirements

SAFETY STANDARD APPROVALS

Safety standard approvals include UL ES 60601-1, CSA C22.2 No. 60601-1 (File No. E178020), and TÜV EN 60601-1.

INPUT SPECIFICATIONS

Input voltage: 80-264 VAC
Power derating: Derate linearly from 100% at 90 VAC to 90% at 85VAC and 80% at 80 VAC
Input frequency: 47-63 Hz
Input current: 2.5 A (rms) for 115 VAC, 1.25 A (rms) for 230 VAC
Earth leakage current: 220 μA max. @ 264 VAC, 63 Hz
Touch current: 100 μA max. @ 264 VAC, 63 Hz

OUTPUT SPECIFICATIONS

Output voltage /current: See rating chart.
Maximum output power: See rating chart.
Ripple and noise: 1% peak to peak maximum
Over voltage protection: Provided and set at 112-140% of its nominal output voltage, latching by recycle input to reset
Short circuit protection: Automatic recovery
Over temperature protection: Latching by recycle input to reset
Temperature coefficient: ±0.04% /°C maximum
Transient response: Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500 µs after a 25% step load change

ENVIRONMENTAL SPECIFICATIONS

Operating temperature: -20°C to +60°C
Atmospheric pressure: 540 hPa to 1060 hPa
Storage temperature: -40°C to +85°C
Relative humidity: 5% to 95% non-condensing
Temperature derating: Derate from 100% at +40°C linearly to 50% at +60°C

GENERAL SPECIFICATIONS

Switching frequency: 50-130 KHz
Power factor: 0.98 Typical at 115 VAC
Efficiency: 89% min. at full load
Hold-up time: 20 ms minimum at 100 VAC
Line regulation: ±0.5% maximum at full load
Inrush current: 130 A @ 115 VAC or 260 A @ 230 VAC, at 25°C cold start
Withstand voltage: 4000 VAC from input to output (2 MOPP), 1500 VAC from input to ground (1 MOPP), 500 VAC from output to ground. (For class II models, 4000VAC from input to output)

MTBF & EMC PERFORMANCE

MTBF: 100,000 hours at full load at 25°C ambient, calculated per MIL-HDBK-217F
EMC Performance:

EN55011: Class B conducted, Class B radiated
EN61000-3-2: Harmonic distortion, Class A and D
EN61000-3-3: Line flicker
EN60601-1-2 Compliance:

EN61000-4-2: ESD, ±15 KV air and ±8 KV contact
EN61000-4-3: Radiated immunity, 9-28 V/m
EN61000-4-4: Fast transient/burst, ±2 KV
EN61000-4-5: Surge, ±1 KV diff., ±2 KV com.
EN61000-4-6: Conducted immunity, 10 Vrms
EN61000-4-8: Magnetic field immunity, 30 A/m
EN61000-4-11: Voltage dip immunity, 30% reduction for 500 ms (criteria A @ 230VAC, criteria B @ 100VAC), 60% reduction for 100 ms (criteria A @ 230VAC, criteria B @ 100VAC) and >95% reduction for 20 ms

OUTPUT VOLTAGE/CURRENT RATING CHART

Model (Class I)	Model (Class II)	V1	Max. Current	Tol.	Ripple & Noise	Max. Power	Average Active Efficiency (@115/230 Vac)
PMP250-12	PMP250F-12	12 V	18.34 A	±5%	120 mV	220 W	89/89%
PMP250-13	PMP250F-13	15 V	14.67 A	±5%	150 mV	220 W	89/89%
PMP250-13-1	PMP250F-13-1	18 V	13.89 A	±5%	180 mV	250 W	89/89%
PMP250-13-2	PMP250F-13-2	19 V	13.16 A	±5%	190 mV	250 W	89/89%
PMP250-13-3	PMP250F-13-3	20 V	12.50 A	±5%	200 mV	250 W	89/89%
PMP250-14	PMP250F-14	24 V	10.42 A	±5%	240 mV	250 W	90/90%
PMP250-15	PMP250F-15	27 V	9.26 A	±5%	270 mV	250 W	90/90%
PMP250-16	PMP250F-16	30 V	8.34 A	±5%	300 mV	250 W	90/90%
PMP250-16-1	PMP250F-16-1	32 V	7.82 A	±5%	320 mV	250 W	90/90%
PMP250-17	PMP250F-17	36 V	6.95 A	±5%	360 mV	250 W	90/90%
PMP250-18	PMP250F-18	48 V	5.21 A	±5%	480 mV	250 W	90/90%
PMP250-19	PMP250F-19	54 V	4.63 A	±5%	540 mV	250 W	90/90%

MECHANICAL SPECIFICATIONS

The power supply unit is enclosed in a 94V-0 rated polycarbonate case. It features an LED indicator. The AC input is via an IEC320/C14 inlet (Class I) or IEC320/C18 inlet (Class II). The output connector is a Molex Mini-Fit receptacle (P/N: 39-01-2060 or 39-01-2080) with female terminal #5556 or equivalent, mating with Molex plug 39-01-2066 (or P/N: 39-01-2086) and male terminal #5558 or equivalent. It also mates with Molex headers #5566, #5569, or equivalent.

Dimensions are approximately 204.0 mm (8.03 inches) in length, 91.4 mm (3.60 inches) in width, and 36.0 mm (1.42 inches) in height, with a tolerance of 0.5 mm [0.02 inches]. The approximate weight is 1100 grams (2.425 lbs).

The 'Output Power Derating Curve' shows that output power is 100% at ambient temperatures up to 40°C and derates linearly to 50% at 60°C.

PIN CHARTS

PIN CHART (output 18Vdc to 54Vdc)

This chart details the pin assignments for output voltages from 18Vdc to 54Vdc. Pins are designated for +V1 (positive voltage), V1 (negative voltage), and Return.

PIN CHART (output 12Vdc to 54Vdc)

This chart details pin assignments for output voltages from 12Vdc to 54Vdc, similar to the 18Vdc chart, with variations in pin usage for positive voltage (+V1), negative voltage (V1), and return (Return).

CONTACT INFORMATION

For inquiries, contact FSP Power Solution GmbH:

Email: info@fsp-ps.de
Website: www.fsp-ps.de / www.fsp-group.com.ru
Address: Jakobshöhe 16 / 41066 Mönchengladbach / Germany
Phone: +49 (0) 2161 4952490
Fax: +49 (0) 2161 495249 21

	FSP PM400 Series 400W Medical & ITE Power Supplies Datasheet Datasheet for FSP PM400 Series AC-DC switching power supplies, featuring 400W output, medical and ITE certifications, high efficiency, and detailed specifications for various models.
	FSP PMP60N1 Series 60W Medical & ITE Power Supplies Datasheet Datasheet for FSP PMP60N1 series 60W AC/DC switching power supplies, detailing specifications, features, safety approvals, and performance for medical and ITE applications.
	FSP PM42 Series 30-48W Medical & ITE Power Supplies Datasheet Datasheet for FSP PM42 Series AC-DC switching power supplies, offering 30-48W output power. Features include wide-range input (90-264 VAC), medical and ITE safety approvals (EN60601-1, EN62368-1), low earth leakage, and Level B emissions. Suitable for medical, IT, and industrial applications.
	FSP500-50RDB 500W 1U Redundant Power Supply Datasheet Technical datasheet for the FSP500-50RDB, a 500W 1U redundant switching power supply designed for industrial environments, IPC controllers, and workstations. Features 80 Plus Bronze certification, high reliability, and comprehensive protection.
	FSP 500W Medical ATX Power Supplies - MPE Series Datasheet Technical datasheet for FSP's MPE Series 500W Medical ATX Power Supplies, detailing features, specifications, safety approvals, and mechanical dimensions. Includes input/output ratings, environmental conditions, and EMC performance.
	FSP250-60RCB 250W 1U Redundant Power Supply Datasheet \| FSP Technical datasheet for the FSP250-60RCB, a 250W 1U redundant switching power supply. Features 80 Plus Bronze efficiency, hot-swappable modules, and industrial application suitability. Includes specifications, dimensions, and safety approvals.
	FSP180-50FEB Flex ATX 180W Power Supply Datasheet Technical datasheet for the FSP180-50FEB, a 180W Flex ATX switching power supply. Features 80 Plus Bronze certification, high reliability, and compliance with safety standards for industrial applications.
	FSP PMP250F Series Switching Power Adapter CB Test Certificate - IEC 60601 Compliance Official CB Test Certificate (DE 2-040399) for FSP Group Inc.'s PMP250F series switching power adapters, confirming compliance with IEC 60601-1 and IEC 60601-1-6 standards. Includes product details, ratings, and manufacturing locations.

FSP PMP250 Series 220-250W Medical Power Supplies

PMP250 SERIES