Momcozy Video Baby Monitor BM01 User Guide

Looking for help?

Contact Momcozy for expert support.

www.momcozy.com

support@momcozy.com

Safety Instructions

Strangulation Hazard: Keep cords out of reach of children (more than 3 ft / 0.9 m away). Do not remove the tag.

NEVER place the camera or cord in or near the crib or playpen.

NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.

Only use the AC adapters provided.

Never use the unit near water, including near a bathtub, sink, laundry machine tube, or wet basement.

Do not install near heat sources such as radiators, heat registers, stoves, or other devices that produce heat.

Only use attachments and accessories specified by the manufacturer.

Unplug this device when unused for long periods of time.

CAUTION

This product is NOT a toy. Do not allow children to play with it.

This product is NOT intended to replace the proper supervision of children. You MUST check your child's activity regularly.

This product is not intended for use as a medical camera and its use should not replace adult supervision.

Unplug the product during lightning storms.

Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis thereafter.

Check the reception regularly. Test the camera before use and after changing the camera's location.

For indoor use only.

Clean the camera with a dry cloth only.

Do not block any ventilation openings.

Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5 m / 4.9ft apart.

Package Contents

• Camera
• Baby Monitor
• Wall Mount Bracket
• User Guide
• Power Cable x 2
• Adapter x 2
• User Guide
• Screw x 2
• Wall Anchor x 2

Product Overview - Monitor

1. Power On/Off & LCD On/Off: Press and hold for 3 seconds to turn on/off the monitor. Short press: Turn on/off the LCD screen. When the screen is turned on, press and hold for 8 seconds to reset the system.

2. Volume adjustment: Press the left button to reduce the speaker volume, and press the right button to increase the speaker volume.

3. Menu: Press [Menu] to enter/exit the menu.

4. Camera Switch: Press [Switch Camera] to switch to another camera if connected with two or more cameras.

5. Charging Indicator: Solid blue during charging, and goes out when fully charged; Blinking red when the monitor is in a low power state.

6. Up Button: Press [Up] to move the camera upward or to change your selection upward.

7. Left Button: Press [Left] to move the camera leftward or to change your selection leftward.

8. Right Button: Press [Right] to move the camera rightward or change your selection rightward.

9. Confirm/Zoom Button: Press [OK] to zoom in/out to confirm your selection.

10. Down Button: Press [Down] to move the camera downward or change your selection downward.

11. Monitoring Status Indicator: Green. When the camera is disconnected, it flashes slowly; when the camera enters pairing mode, it flashes quickly; when the camera is turned on, it remains steady.

12. Indicator: 1. The louder the sound is received by the monitor, the more indicator is on. 2. Signal indicator (temperature alarm/off-connection alarm/feeding alarm).

13. Talk: Press [Talk] to talk to your baby.

14. Lullaby: Press [Lullaby] to select your desired lullaby song.

15. Indicator: The louder the sound is received by the monitor, the more indicator is on.

16. Microphone.

17. Stand.

18. Speaker.

Product Overview - Camera

• 1. Night Vision Sensor
• 2. Pair Button
• 3. Camera Lens
• 4. Microphone
• 5. Speaker
• 6. Antenna
• 7. Charging Port
• 8. Infrared LEDs
• 9. Temperature Sensor
• 10. Threaded Socket

Getting Started

1. Charging & Powering Baby Monitor

1. Connect the monitor adapter to the monitor and a power outlet.
2. Unplug the unit when its power indicator turns off, indicating a full charge. Unplug the unit after fully charging the monitor, which can prolong the lifespan of the device.

2. Powering Camera

1. Connect the camera to power source via the USB Type-C cable and camera adapter.
2. Only use the power adapters provided.
3. Do not place the camera and power cord within the reach of your baby.

3. Pairing the Baby Monitor & the Camera

By default, one camera is paired with the monitor. When you power on the monitor and camera, the two will automatically pair.

Adding a new camera to the baby monitor

Step 1:

1. Press [Menu] to enter the menu page.
2. Choose [Add] -> [OK] button.

Step 2:

1. Select through [Add] -> [OK] button.

Step 3:

1. Press the [PAIR] button on the rear of the camera.
2. The monitor will then auto-pair with the camera.

Once paired successfully, the camera number with its icon will be shown at the top left of the screen.

It is recommended to pair in the baby's room, or wherever you intend to place the camera.

High-pitched noises might occur when the monitor is too close to the camera. Please keep them at least 1.5 m / 4.9ft apart.

The monitor can connect up to 4 cameras at once.

4. Placing the Camera

For safety concerns and better vision in night vision mode, if the camera is placed on a 0.75 m / 2.5ft tabletop, the distance from the baby should be at least 1.5 m / 4.9ft. The baby monitor has an infrared night vision capacity up to 6 m / 19.7ft. Most importantly, make sure that the camera power cord is out of your baby's reach.

Diagram showing recommended placement of the camera relative to a crib, indicating distances of 0.75m and 1.5m.

5. Wall Mounting Camera

1. Rotate the knob counter-clockwise to adjust the wall mount bracket, then fasten the joint and secure the angle.
2. Mark the upper and lower holes with a pencil.
3. Drill holes in the wall (using a 17/64 inch drill bit) and insert wall anchors into the holes with a hammer.
4. Fasten the wall mount bracket with screws.
5. Place the camera on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the camera.
6. You can maximize your camera unit's viewing angles by tilting the wall mount bracket. Tilt your camera up or down to adjust to your preferred angle.

Diagrams illustrating the steps for wall mounting the camera.

Do not release the camera until it is firmly mounted.

Functions & Operations

Status Icons

• No Signal
• Signal Strength
• Cycle Cameras Enabled (rotates every 10 seconds)
• Camera
• Current Time
• Lullabies Enabled
• VOX Function on
• Temperature Alarm
• Feeding Reminder
• Volume Mute
• Night Vision Mode
• Current Room Temperature
• Battery Level
• Alarm Mute

You can use the auto-scan function by short pressing the [Scan] button until you see the [Scan] icon on the screen. Then the camera view cycles through the list of connected cameras every 10 seconds. If an alarm occurs, the auto-scan function will pause temporarily.

1. Volume Adjustment

Use Shortcut Button: Press the [Volume +/-] button to quickly adjust the volume.

To adjust system sound, navigate to [Menu] -> [Sound] -> [Alarm Volume].

2. Selecting a Camera & Scanning Cameras

Note: This function requires more than two cameras to be turned on. Multiple cameras must be powered on and within the monitor's connection range.

Selecting a Camera

Step 1: Check the camera icons, click [Next Camera] to switch to the next camera view.

Scanning Cameras

Step 2: After switching all camera views, click [Scan] again. The camera view then transits from one to another connected camera every 10 seconds, displaying a loop icon at the top left of the screen.

Step 3: Click [Scan] again to stop scanning. The camera will then switch to a single camera view.

3. Digital Zoom

Press the [Zoom] button to zoom in the screen to 2X and 4X respectively in camera viewing mode. Press the [OK] button for the third time to adjust the zoom setting back to default.

4. Lullaby

Use Shortcut Button: Press [Lullaby] to enter the lullaby page. Press [Left/Right] buttons to select the lullaby song, press [Up/Down] buttons to adjust the volume of the lullaby, and press [OK] to turn on or off the lullaby.

Step 2: Select your desired lullaby and press [OK] to turn it on/off. Press Up/Down buttons to increase or decrease the lullaby sound. Select [Loop] to play the lullaby on a loop.

5. Talk Back

Press and hold the [Talk] button to talk to your baby; release it to exit the talking mode.

• When in monitoring mode, press and hold the [Talk] button to enter intercom mode; the [Intercom] icon will be displayed on the monitor. The intercom function can still be used when accessing the menu, but the [Intercom] icon will not appear on the screen.
• If the device is muted or the speaker volume is too low, you may not be able to hear the baby.
• When you press the [Talk] button, the camera will not transfer sound to the monitor. Please release the button to listen to your baby.

6. Brightness

Explanation: This function is used to adjust the screen brightness of the monitor.

Step 1: Press [Menu] to enter the menu page. Choose [Brightness] -> [OK] button.

Step 2: Select the Brightness Setting to change the monitor screen brightness.

7. Screen Sleep

Explanation: This function sets the monitor screen to sleep without powering off the monitor.

Step 1: Press [Menu] to enter the menu page. Choose [Screen Sleep] -> [OK] button.

Step 2: Select the Screen Sleep option and choose the desired time. The screen will automatically light up if there is a VOX or temperature alert. When VOX is turned off, the screen will not automatically wake up. When the sleep time is set to "OFF", the monitor screen will not turn off.

Click [Customize] to enter the page for customizing the resting time. The resting time ranges from 1 to 60 minutes.

8. Add A New Camera

Step 1: Press [Menu] to enter the menu page. Choose [Add] -> [OK] button.

Step 2: Select through [Add] -> [OK] button.

Step 3: Press the [PAIR] button on the rear of the camera. The monitor will then show the camera is paired successfully.

The monitor can connect up to 4 cameras at once.

9. Split Screen

Explanation: This function displays two camera views on a single screen.

Step 1: Press [Menu] to enter the menu page. Select [Split Screen] -> [OK] button.

Step 2: Select another camera that needs a split screen and press [OK]. The monitor will then display a split screen view.

Select the camera on the split screen and press [OK]. If the camera is not selected, the monitor will exit the split screen mode.

10. Selecting a Camera & Scanning

Note: This function requires more than two cameras to be turned on. Multiple cameras must be powered on and within the monitor's connection range.

Step 1: Press [Menu] to enter the menu page. Select [View] -> [OK] button.

Step 2: Select the camera you want to switch to and press [OK] button.

Step 3: If you need to cycle multiple camera views, select [Scan] -> [OK] button.

11. Deleting A Camera

Step 1: Press [Menu] to enter the menu page. Select [Del] -> [OK] button.

Step 2: Select the camera you want to delete and press [OK] button.

Step 3: Select [YES]. The camera is deleted successfully.

12. Speaker Volume

Explanation: This function is used to adjust the speaker volume of the monitor.

Step 1: Press [Menu] to enter the menu page. Choose [Speaker Volume] -> [Left/Right] button to decrease/increase the volume, and press [OK] Button to save your settings.

13. Alarm Volume

Explanation: This function is to adjust the monitor system sound.

Step 1: Press [Menu] to enter the menu page. Select [Alarm Volume] -> [OK] button.

Step 2: Select the preferred alarm sound level. Press [OK] button.

14. VOX

Explanation: This function wakes up the monitor screen and lights it up. There are three wake-up levels (low/medium/high). When the sound detected by the camera reaches 75dB/65dB/60dB or more, the monitor will wake up to trigger the alarm and the LED indicator will flash.

Caution: The screen will not wake up automatically if VOX is turned off.

Step 1: Press [Menu] to enter the menu page. Choose [VOX] -> [OK] button.

Step 2: Select the option you want. Press [OK] button.

The default setting is low sensitivity. If you mute the monitor, no alarm (except for the 75dB alert) will be triggered. Please use this function carefully.

15. Alarm Clock

Explanation: This function reminds you of feeding your baby. "OFF" means you turn off the function; "2 hours" means it reminds you every 2 hours, and so on for other options.

Step 1: Press [Menu] to enter the menu page. Choose [Alarm Clock] -> [OK] button.

Step 2: Select [Remind] and set the time you want. Press [OK] to start/finish setting. [Start] stands for starting the setting. [Finish] stands for finishing the setting.

Step 3: Select [Repeat] to create a recurring alarm and choose the scheduled time you want your alarm to repeat.

16. Date/Time

Step 1: Press [Menu] to enter the menu page. Choose [Time/Date] -> [OK] button.

Step 2: Press [OK] to start/finish setting. [Start] stands for starting the setting.

Step 3: [Finish] stands for finishing the setting. Use Up/Down/Left/Right buttons to select and press [OK] button to confirm.

17. Temperature

Explanation: You can set the maximum/minimum temperature and turn on the temperature alert, so the baby monitor beeps whenever the room temperature falls outside the desired range. You can also choose to display the temperature in Fahrenheit (°F) or Celsius (°C) on your monitor.

Step 1: Press [Menu] to enter the menu page. Choose [Temperature] -> [OK] button.

Step 2: Press [OK] to start/finish setting. [Start] stands for starting the setting. [Finish] stands for finishing the setting.

A temperature alarm can be temporarily turned off by pressing any button on the monitor.

18. Night Vision

Explanation: In normal mode, the camera displays color images during the day; during nighttime, the camera displays black and white images.

Step 1: Press [Menu] to enter the menu page. Choose [Night Vision] -> [OK] button.

Step 2: Press [OK] button to switch to night vision mode.

When the camera is set to night vision mode, the monitor will display black and white images both day and night.

19. Language

Explanation: There are four languages available in your device; you can choose your language here.

Step 1: Press [Menu] to enter the menu page. Choose [Language] -> [OK] button.

Step 2: Select the desired language and press [OK] button.

20. Lullabies

Explanation: This function is to comfort the baby with soothing lullabies.

Step 1: Press [Menu] to enter the menu page. Choose [Lullabies] -> [OK] button.

Step 2: Select your desired lullaby and press [OK] to turn it on/off. Press Up/Down buttons to increase or decrease the lullaby sound. Select [Loop] to play the lullaby on a loop.

21. Refresh Rate

Explanation: You can change the image refresh frequency of the camera to ensure that the camera works normally.

Step 1: Press [Menu] to enter the menu page. Choose [Refresh Rate] -> [OK] button.

Step 2: Set the refresh frequency based on your usage in your area.

22. Factory Settings

Explanation: System will be restored to default Settings.

Step 1: Press [Menu] to enter the menu page. Choose [Factory Setting] -> [OK] button.

Step 2: Choose [YES] -> [OK] button to start restoring factory settings.

Press and hold the display power button for 8 seconds to force the display to shut down.

23. Contact Us

Step 1: Press [Menu] to enter the menu page. Choose [Contact Us] -> [OK] button.

Step 2: Press [Menu] to return to the menu page.

Specifications

Monitor

Camera

Troubleshooting

Warranty & Customer Service

12 months guarantee (contact information can be found on the monitor or on the cover of this user manual).

FCC Compliance (Camera)

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC 20cm Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met.

This product meets the applicable Industry Canada technical specifications.

Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes : 1)L'appareil ne doit pas produire de brouillage; 2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipementdevrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

FCC Compliance (Monitor)

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC statement (Monitor)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
3. The device has been evaluated to meet general RF exposure requirement.
4. The device can be used in portable exposure condition without restriction.

Cet appareil contient des émetteurs/récepteurs exemptés de licence qui sont conformes aux flux RSS exemptés de licence de Innovation, Science et développement économique Canada. L'exploitation est soumise aux deux conditions suivantes:

1. cet appareil ne doit pas causer d'interférences.
2. ce dispositif doit accepter toute interférence, y compris toute interférence susceptible de provoquer un fonctionnement indésirable du dispositif.
3. l'appareil a été évalué pour répondre aux exigences générales d'exposition aux RF. Le dispositif
4. peut être utilisé dans des conditions portatives d'exposition sans restriction

FCC/IC RF Radiation Exposure and SAR Statements

The xTablet T1190 has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC/IC has established detailed SAR requirements and has established that these requirements. RF Exposure Information The radio module has been evaluated under FCC Bulletin C95.1 and IEEE 1528 and found to be compliant to RF Exposure from radio frequency devices. This model meets the applicable government requirements for exposure to radio frequency waves. The highest reported SAR level for usage near the body (0mm) is 0.518 W/kg