Lumary Smart Ceiling Fan Light User Manual

Brand: Lumary

Model: L-CFL18A1

Introduction

Thank you for choosing Lumary products. This user manual provides instructions for setting up and using your Lumary Smart Ceiling Fan Light. Download the Lumary App to manage your devices from your phone and tablet, connect to your home Wi-Fi, and control multiple devices with ease. Lumary is a professional smart lighting producer committed to providing top-tier service and continuously optimizing its applications and products.

Product & Notes

What's in the Box

The package contains the following items:

Lumary Smart User Manual
Lumary Smart Ceiling Fan Light

Package Contents

Hardware:

M5x35mm Screws and concrete anchors: For installing the hanging plate to the ceiling.
M2x20mm Screws and concrete anchors: For installing the remote holder.
M4x32mm Screws and caps: For installing the mounting plate to the J-Box (J-Box not included).
M3x10mm Screws: For securing the mounting plate.
Nuts Cap: Small plastic caps.
Remote and holder: One remote control unit and its wall-mount holder.

Get Ready

Ensure you know your Wi-Fi network name and password.
Your mobile device should be running iOS 13.3 or higher, or Android 9.0 or higher.
Connect to a 2.4GHz Wi-Fi network. Lumary devices cannot connect to 5GHz networks.

Installation Instructions

IMPORTANT:

Read all instructions before installing fixtures. Retain for future reference.

SAFETY:

For your safety, this fixture must be wired in accordance with local electrical codes and ordinances. All work should be performed by a qualified electrician.

WARNING:

Ensure power is OFF from the electrical panel before starting installation or attempting any maintenance. This is an indoor installation only.

Step 1: Turn off power. A diagram shows a hand switching off a circuit breaker. Ensure the power of the circuit breaker is turned off before installation.

Step 2: Attach hanging plate. A diagram shows the hanging plate being screwed to the J-Box. Screw the hanging plate to the J-box. Connect the wires using the Terminal Cap. (Black wire is positive, white wire is negative).

Step 3: Secure hanging plate to ceiling. A diagram shows screws attaching the mounting plate to the ceiling.

Step 4: Attach lamp body. A diagram shows the lamp body being rotated to secure it to the hanging plate.

Step 5: Tighten mounting plate screws. A diagram shows screws being tightened to ensure the lamp is installed firmly.

Step 6: Turn on power. A diagram shows a hand switching on a circuit breaker. Turn on the power of the circuit breaker.

Application Connection

1. Download and install the "Lumary" App. Search for the Lumary App on the App Store or Google Play. Screenshots show the app search results and download buttons for both platforms.

2. Register a Lumary account. Screenshots show the app's login/registration screens where you can enter your email address, password, and select your region and country.

3. Connect your device.

NOTE: Lumary products cannot connect to 5GHz networks.
Steps:
Enable Bluetooth on your mobile device to easily add Wi-Fi devices.
When the device is powered on without a network connection, confirm the light is breathing or blinking in pairing mode.
Open the Lumary App. In the top corner of the Devices screen, tap "+" and select "Add Device" to confirm the device is paired.
If the device is not pairing, use the wall switch to reset it: turn it on-off-on-off-on.
Find the device, choose Wi-Fi, enter the password, and press "Next". Tap "Add" and wait patiently. Tap "Done" when the device is successfully added to the App.
Alternative connection methods: Open the Lumary App, tap "+" in the top corner, choose "Lighting", select "Light Source (BLE + Wi-Fi)", then select "AP Mode" or "EZ Mode" in the upper right corner.

Screenshots illustrate the app interface for adding devices, selecting Wi-Fi networks (with a note that 5GHz is not supported), and confirming successful device addition.

Troubleshooting

Cannot connect to your Wi-Fi network: Ensure you entered the correct Wi-Fi password. Check for general internet connection problems. If the Wi-Fi signal is weak, reset your Wi-Fi router and try again.
Fail to bind device: You may need two phones: one to set up a hotspot and the other to connect to it and add the device via the app. If the device is successfully added, it is normal. The issue might be with your router's settings (MAC or DHCP restrictions). Lumary products do not support 5GHz networks.
Device appears offline or unreachable: Ensure your Wi-Fi router is online and within range. Check for the latest Lumary functionality by selecting "Check for firmware update" in your device settings. Try turning off the device, clearing the app cache, rebooting the router, and then turning the device back on after one minute. Confirm the device status after five minutes.
How to reset the device: To reconnect to Wi-Fi, reset the device using the wall switch: on - off - on - off - on. A single reset (on-off-on-off-on) will reach Easy Mode, indicated by a rapidly blinking white light. Refer to the "Connect in Easy Mode" section. Long press button "6" on the remote for 5 seconds to make the fan light enter App pairing mode.
Questions: Contact Lumary customer service via email at support@lumary.tech or leave a message on their official social media accounts.

Group Control

1. Create a group: Log in to the Lumary App, tap the smart device, and enter its settings. Tap the edit icon (✏️) in the top right corner.

2. Select devices for the group: Tap "Create Group", then select the devices you want to include and tap "Save". Screenshots show the app interface for creating and adding devices to a group.

3. Name and save the group: You can reset the group name and save it. The group can then control all added devices simultaneously. Screenshots show the group naming interface and the main device list with the newly created group.

Remote Control

The remote control and fan light are paired by default. If the remote control does not work, re-pair it as follows:

Connect the fan light to the power supply and ensure it works normally (the light comes on slowly).
Turn the fan light off for 5-10 seconds, then turn it back on using the wall switch.
Press and hold button "1" (Power) until the fan light blinks 3 times rapidly, then release it.
Remote control pairing is successful. You can now use the remote to control the fan light.

Remote Button Functions:

1: Turn On/Off
2: Wind Mode (Nature/Soft)
3: Fan Rotation (Forward/Reverse)
4: Shaking Head (Not supported yet)
5: Fan Speed (1 is weakest, 6 is strongest)
6: Fan On/Off (Long press 5 seconds to trigger pairing mode)
7: Turn on White Color
8: Turn on RGB Color
9: Change Brightness (Up/Down arrows)
10: Change Color Temperature (Up/Down arrows)
11: Change RGB Color (Up/Down arrows)
12: Change RGB Mode
13: Countdown Timing (1 Hour / 4 Hours)

A diagram illustrates the remote control with numbered buttons corresponding to the functions listed above.

To make the fan light enter App pairing mode, long press button "6" for 5 seconds.

FAQ

Why does flickering occur with Lumary products? Lumary products are factory set to default network configuration. If the device is not connected to the network, it will flash for three minutes each time it is powered on. Once connected, it will stop flashing and automatically connect when switched off and on via the wall switch after 15 seconds.
What should I do if the device appears offline or is unreachable? Ensure your Wi-Fi router is online and in range. Check for the latest Lumary functionality by selecting "Check for firmware update" in your device settings. Try turning off the device, clearing the app cache, rebooting the router, and then turning the device back on after one minute. Confirm the device status after five minutes.
How do I reset the device? To reconnect to Wi-Fi, reset the device using the wall switch: on - off - on - off - on. A single reset (on-off-on-off-on) will reach Easy Mode, indicated by a rapidly blinking white light. Refer to the "Connect in Easy Mode" section. Long press button "6" for 5 seconds to make the fan light enter App pairing mode.
How many devices can I control?
- Maximum timers per device: 30
- Maximum devices per home: 120
- Maximum Tap-to-Run scenes per home: 100
- Maximum Automations per home: 100
- Maximum tasks per Tap-to-Run: 150
- Maximum tasks per Automation: 150
- Maximum conditions per Automation: 10
- Maximum mobile devices logged in simultaneously per account: 200
- Maximum Homes per App account: 20
- Maximum home members per home: 20
- Maximum rooms per home: 20
- Maximum devices per room: 50
- Maximum devices per device group: 100
- Maximum device groups per home: 20
- Maximum device groups shared with other users: 20
- Maximum devices shared with other users: 20
- Maximum App accounts invited by other homes: 20
What should I do if I find a problem with the purchased product? Please email support@lumary.tech with your Amazon order ID. Lumary is dedicated to ensuring 100% satisfaction and will happily exchange a faulty product for a new one immediately.

Parameter Information

Name	Lumary Smart Ceiling Fan Light
Model	L-CFL18A1
Input Voltage	100-130VAC, 60Hz
Wattage	Light: Max. 35W, Fan: 15W
Color Temperature	RGBAI + Tunable White (2700K-6500K)
CRI	80+
Lumens	2800lm
Beam Angle	120°
Rated Life	25000h

Certifications: FC, RoHS. FCC ID: 2ANDL-CB3S. Made in China.

CAUTION: FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Voice Control Guide

Name and Control Each Device by Voice.

This device works with Amazon Alexa and Google Assistant.

Work With Amazon Alexa

1. Link Lumary App to Amazon Alexa: Log in to the Lumary App, tap the smart device, and enter its settings. Tap the edit icon (✏️) in the top right corner. Tap "Alexa" under Third-party Control. Tap "Sign In With Amazon".

2. Authorize access: Click "Allow" to sign in to Lumary. Screenshots show the authorization process.

3. Linking successful: Once linked, you can discover new devices in Alexa. To control your Lumary smart device, ask Alexa. Make sure your devices are already set up using the Lumary app.

Example commands:

"Alexa, discover my devices."
"Alexa, turn on the bedroom light."
"Alexa, set the bedroom light to orange."
"Alexa, turn off the coffee machine."
"Alexa, set the living room to 50%."
"Alexa, dim porch light."

*Some commands require compatible devices.

Work With Google Assistant

1. Link Lumary App to Google Assistant: Log in to the Lumary App, tap the smart device, and enter its settings. Tap the edit icon (✏️) in the top right corner. Tap "Google Assistant" under Third-party Control. Tap "Link with Google Assistant".

2. Authorize access: Click "Agree and link". Screenshots show the authorization process.

3. Linking successful: Once linked, you can discover new devices in Google Home. To control your Lumary smart device, say "Hey Google" and ask. Make sure your devices are already set up using the Lumary app.