Lumary Smart LED Deck Light User Manual

Thank you for choosing Lumary products. Ready to get started? Download the Lumary App to manage your devices from your phone and tablet. Easily connect to your home Wi-Fi and control multiple devices with touching fingertips. Lumary is a professional, authentic smart lights producer, committed to providing top-tier service and continuously optimizing its application and products.

Product & Notes

What's in the Box

The package includes:

Part A: Lumary Smart LED Deck Light A (Quantity: 6)
Part B: Mounting Screws & Plastic Anchors (Quantity: 12)
Part C: Waterproof Wire Nuts (Quantity: 13)
Part D: Bluetooth Remote Controller (Quantity: 1, AAA battery not included)

Get Ready

Know your Wi-Fi network and password.
Ensure your mobile device is running iOS 13.3 or higher and Android 9.0 or higher.
Ensure you are connecting to a 2.4GHz Wi-Fi network (Lumary cannot connect to 5GHz networks).

WARNING

PLEASE READ ALL SAFETY PRECAUTIONS AND INSTALLATION INSTRUCTIONS CAREFULLY BEFORE INSTALLING THE FIXTURE.

Please check and make sure there is no sign of physical damage to the product when unpacking. DO NOT use damaged products.
Turn off the power before installing or servicing.
Due to the risk of fire or electric shock, installation of this product requires knowledge of electrical systems. If you are not qualified, do not attempt installation. Contact a qualified electrician.
Please handle gently to ensure the lifespan and appearance of the product.
This LED deck light uses 12-24V low voltage. Please check that your supply voltage matches the voltage marked on the label prior to connecting to supply leads.

Electrical Connection Diagram: The system requires a low voltage transformer. Input is AC 120V/50Hz, and the output is 12-24V AC/DC.

Installation Instructions

Drill two holes in the wall.
Tap the plastic anchors into the holes.
Align the holes on the fixture with two plastic anchors.
Tighten the fixture to the plastic anchors with the screws.
Use the waterproof wire nuts to connect the wires. The input power cord requires 12-24V AC/DC.

Application Connection

Step 1: Download and Install the Lumary App

Find and install the "Lumary" App on the App Store or Google Play.

Step 2: Register a Lumary Account

Enter your email address and create a password. Agree to the Privacy Policy and User Agreement. Log into the App. Note: Please select your region and country.

Step 3: Connect Your Smart Device

Connect your Lumary smart device to the app using Bluetooth communication. Note: If the device needs voice control, timing, and remote control, a gateway (Model: L-GW0A1) is required.

Connection Steps:

Ensure your phone is connected to a network and Bluetooth is turned on.
Power on the light; it will start flashing or breathing to indicate pairing mode.
In the Lumary App, click the "+" icon to search for nearby devices on the network. Once the device is located, click "Add" to add it to the App.
If you wish to use a gateway, please refer to the gateway guide for further instructions.

Step 4: Enter Wi-Fi Information

Choose your Wi-Fi network and enter the password. Ensure you are connecting to a 2.4GHz network, as 5GHz networks are not supported.

After successful connection, the app will show devices added successfully. Click "Done".

Group Control

Step 1: Access Device Settings

Step 2: Create a Group

Click "Create Group", then select the device(s) you want to include in the group and save.

Step 3: Name and Control Group

You can reset the group name and save it. The group can then control multiple devices simultaneously.

Beacon Remote Controller

The Lumary Beacon Remote Controller allows for convenient control of your smart lights.

Remote Functions:

ON/OFF: Powers the device on or off.
Night Light: Activates a low-brightness mode.
7 Colors: Cycles through preset colors.
Brightness+/-: Adjusts the brightness level.
Temperature+/-: Adjusts the color temperature (e.g., warm to cool white).
K- RGB K+: Controls RGB color mixing and color temperature.
Group A/B/C/D: Assigns devices to specific groups for control.
Scene: Activates pre-set lighting scenes.

Pairing the Remote Controller:

Note: Not all devices are compatible with the remote controller. For details, contact support@lumary.tech.

The device is powered by 2xAAA dry batteries.
First, the light must be bound to the Lumary App.
Use the wall switch to disconnect power for 5 seconds, then turn it back on. The light and remote control should be in pairing status.
Long press any group key (A/B/C/D) until the light blinks to indicate successful pairing. If devices are not fully paired, press and hold the group button again. Repeat steps 3-4 if pairing takes longer than 1 minute.

Remote Key Usage:

Short press ON/OFF: Controls devices paired under grouping.
Long press Group key: Initiates device pairing.
Long press "Grouping Key" and "Brightness-" combination: Unpairs all devices under the grouping.
Bind: Long press Group A/B/C/D key until the device blinks or breathes.
Unbind: Long press "Brightness-" and any group A/B/C/D key for 3 seconds.

FAQ

Why does flickering occur with Lumary products? Lumary products are factory set to default network configuration. If a device is not connected to the network, it will flash for three minutes each time it is powered on. Once connected, it will stop flashing and automatically connect when switched off and on via the wall switch after 15 seconds.
What should I do if the device appears offline or is unreachable? Ensure your Wi-Fi router is online and in range. Check for the latest Lumary functionality by clicking "Check for firmware update" in your device settings. Try these steps: turn off the device, clear the application cache, reboot the router, turn the device back on after one minute, and check the device status.
How do I reset the device? To reconnect to Wi-Fi, reset the device using the wall switch:
- Reset once (on-off-on-off-on): Enters Easy Mode, indicated by a rapidly blinking white light. Refer to connect in Easy Mode.
- Reset again (on-off-on-off-on): Enters AP Mode, indicated by a slowly blinking white light. Refer to connect in AP Mode.
How many devices can I control? Lumary supports a maximum of 30 timers per device, 120 devices per home, 100 Tap-to-Run automations, 100 Automations, 150 tasks in Tap-to-Run/Automation, 10 conditions in Automation, 200 simultaneous mobile device logins, 20 Homes per account, 20 home members, 20 rooms per home, 50 devices per room, 100 devices per group, 20 device groups per home, and sharing up to 20 devices/groups with other users.
What should I do if I find a problem with the purchased product? Please email support@lumary.tech with your Amazon order ID. Lumary is dedicated to ensuring 100% satisfaction and will happily exchange a faulty product for a new one.

Parameter Information

Parameter	Value
Name	Lumary Smart Deck Light A
Model	L-LDL4A1/6
Input Voltage	12-24V AC/DC
Wattage	2.5W/Per
Color Temperature	RGB +Tunable White (2200K-6500K)
CRI	80+
Lumens	60lm
Beam Angle	120Â°
Rated Life	15000h

Certifications: FCC, RoHS, ETL Listed. FCC ID: 2ANDL-BT3L. Made in China.

CAUTION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Voice Control Guide

Name and control each device by voice using compatible voice assistants.

Work With Amazon Alexa

Linking Lumary with Alexa:

Log in to the Lumary App, tap the smart device, and click the edit icon in the top right corner.
Tap "Alexa" under Third-party Control.
Tap "Sign In With Amazon".
Tap "Allow" to sign in to Lumary.
Linking is successful. When adding new devices, you do not need to link again; simply discover new devices in Alexa.

Example Alexa Commands:

"Alexa, discover my devices."
"Alexa, turn on the bedroom light."
"Alexa, set the bedroom light to orange."
"Alexa, turn off the coffee machine."
"Alexa, set the living room to 50%."
"Alexa, dim porch light."

*Some commands require compatible devices.

Work With Google Assistant

Linking Lumary with Google Assistant:

Log in to the Lumary App, tap the smart device, and click the edit icon in the top right corner.
Tap "Google Assistant" under Third-party Control.
Tap "Link with Google Assistant".
Click "Agree and link".
Linking is successful. When adding new devices, you do not need to link again; simply discover new devices in Google Home.

Example Google Assistant Commands:

"Hey Google, turn on all the lights in my bedroom."
"Hey Google, turn off the light."
"Hey Google, set the bedroom light to orange."
"Hey Google, turn off the coffee machine."
"Hey Google, set the living room to 50%."
"Hey Google, dim porch light."