Lumary Smart Floating Gimbal Light Start Guide

Welcome to the Lumary Smart Floating Gimbal Light. This guide will help you get started with installation, app connection, and smart control.

Product & Notes

What's in the Box

Lumary Smart Floating Gimbal Light

Get Ready

Know your Wi-Fi network name and password.
Ensure your mobile device is running iOS 13.3 or higher and Android 9.0 or higher.
Connect to a 2.4GHz Wi-Fi network (Lumary cannot connect to 5GHz networks).

Attention

Handle the product carefully during transportation.
Do not disassemble the fixture if you are not a professional.
The fixture operates under AC high voltage and current. It should be installed where it cannot be easily touched. The connection must be completely sealed and earthed.
The external flexible cable or cord of this luminaire cannot be replaced. If the cord is damaged, the luminaire shall be destroyed.
The light source contained in this luminaire shall only be replaced by the manufacturer, its service agent, or a similarly qualified person.
The surface where the fixture is positioned must be firm enough to ensure safety.
Ensure the voltage of the electricity system is within the fixture's working voltage range. Otherwise, the fixture's lifetime will be influenced.
Installation and maintenance should be performed by a professional.

Installation

4" LED Floating Gimbal - Installation Instructions

Thank you for purchasing this Lumary lighting product. These instructions are designed to be easy to follow.

IMPORTANT: Read all instructions before installing fixtures. Retain for future reference.

SAFETY: For your safety, this fixture must be wired in accordance with local electrical codes and ordinances. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF from the electrical panel before starting installation or attempting any maintenance. Indoor installation only.

Tools Required:

Saw
Measuring Tape
Electrical Wiring (use type and gauge suitable for application to connect the fixtures)

Pre-Installation:

Turn power OFF from the electrical panel before starting installation.
Locate a suitable position to plate the fixture and open in accordance to the cut-hole dimensions (refer to Hole CutTable for appropriate size).
Run electrical wire from the switch (power supply) through the mounting hole-use NMD90 Romex or BX cable.

Diagram Description (Fig. 1 - Wiring): Shows a connection diagram with a cable going to the fixture. Wires are labeled: Black wire (to fixture), White wire (to fixture), Green wire (ground). Power supply is indicated.

Diagram Description (Fig. 2 - Mounting Box): Illustrates inserting the hardwire box through the mounting hole.

Driver Wiring:

Open the hardwire box swing cover and remove the appropriate knockout(s).
Insert the electrical supply cable through the knockout and secure with a cable connector (sold separately).
Using wire nuts, connect the green ground wire of the cable to the green wire on the box. Connect the white wire of the cable to the white wire of the box. Connect the black wire of the cable to the black wire of the box. (Refer to Fig. 1).
Place all wiring and connections back into the box and close the cover.
Insert the hardwire box through the mounting hole. (Refer to Fig. 2).
For new construction applications: The hardwire box shall be firmly secured to studs, joists, or similar fixed structural units.
For remodel applications: The hardwire box does not require to be firmly secured after the mounting plates, studs, joists, or structural units have been concealed.
Junction box suitable for a maximum of 5 No 12 AWG or 8 No 14 AWG Conductors.

Fixture Installation:

Connect the fixture to the hardwire box by inserting and twisting the male/female connectors. (Refer to Fig. 3).
Push spring-loaded clips on the fixture upwards and insert the fixture base into the mounting hole. Release the clips, and the fixture will be pulled flush to the ceiling. (Refer to Fig. 4).
Once assembly is complete, turn on power to confirm the fixture is working properly.

Diagram Description (Fig. 3 - Connector): Shows the fixture's male/female connectors being joined.

Diagram Description (Fig. 4 - Fixture Base): Illustrates pushing up the spring clips to secure the fixture base to the ceiling.

Application Connection

Install the "Lumary" APP

1. Find and install the "Lumary" app on the Apple App Store or Google Play Store.

App Store Link: Download on the App Store

Google Play Link: GET IT ON Google Play

2. Register a Lumary Account

Enter your mobile phone number or email address to register. Note: Please select your region and country correctly.

Screenshots Description: Shows the Lumary app interface for 'Register' and 'Log In' screens, including fields for email address, password, and region selection.

3. Connect: Easy Mode

STEP 1: Open the Lumary App. In the top corner of the Devices screen, click the '+' icon and select "Add Device".

STEP 2: Choose "Lighting" >> "Light Source(BLE+Wi-Fi)". Select "EZ Mode" in the upper right corner.

STEP 3: Make sure the indicator light is rapidly flashing white. If not, reset the device to reach Easy Mode and press "Next" in the App.

STEP 4: Enter your Wi-Fi network name and password. NOTE: Lumary cannot connect to 5GHz networks. If the connection fails, try connecting using AP Mode.

Screenshots Description: Illustrates the app screens for selecting EZ Mode, resetting the device, confirming the indicator status, and entering Wi-Fi credentials for a 2.4GHz network.

4. Connect: AP Mode

STEP 1: Open the Lumary App. In the top corner of the Home screen, click '+' and choose "Light Source(BLE+Wi-Fi)". Select "AP Mode" in the upper right corner.

STEP 2: Make sure the light is slowly flashing white. If not, reset to reach AP Mode.

STEP 3: Enter your Wi-Fi network and password.

STEP 4: Press "Next" and then "Go to Connect".

STEP 5: Follow the instructions to choose the device from your Wi-Fi list (e.g., "Lumary-XXXX").

STEP 6: The Lumary App will connect to your devices. NOTE: Lumary cannot connect to 5GHz networks. If the connection fails, try connecting using AP Mode.

Screenshots Description: Shows the app screens for selecting AP Mode, confirming the indicator status, entering Wi-Fi details, connecting to the device's hotspot, and the app connecting to the device.

5. Connect: Bluetooth

STEP 1: Open the Lumary App. In the top corner of the Devices screen, click '+'. Choose "Light Source(BLE+Wi-Fi)". Select "Bluetooth" in the upper right corner.

STEP 2: Make sure the light is rapidly flashing white. If not, reset to reach Easy Mode to connect. Press "Next" in the App.

Screenshots Description: Illustrates selecting Bluetooth mode and confirming the light's flashing status.

Group Control

1. Log in to Lumary APP, tap the smart device and enter into its settings by clicking "..." in the top right corner.

2. Click "Create Group", then select a device and save.

3. You can reset the group name and save it. The group can then control devices.

Screenshots Description: Shows the app interface for creating and managing device groups, including selecting devices and naming the group.

FAQ

What should I do if I don't have internet access to my Lumary product? If you do not have a network, you will need two mobile phones: one to set up a hotspot and the other to connect to the hotspot and add the device via the app (refer to the guide).
If my Wi-Fi internet goes down, will Lumary App still work? Lumary products need to be connected to Wi-Fi to be used remotely. The device can also be controlled simply using the app via the LAN as well as Bluetooth (e.g., on, off, dimming, color temperature, colors).
Why does flickering occur with Lumary products? Lumary's products are factory set to the default network configuration. If the device has not been connected to the network, it will flash for three minutes each time it is powered on. If the device is connected to the network, it will stop flashing and will automatically connect to the network when it is switched off and on via the wall switch after 15 seconds.
Can I share with family and friends? Yes, you can share access to your Lumary devices. In the Lumary App, from your main device list, click on one of the devices, press the "..." button on the top right, and click on "Share Device" to give or revoke sharing permissions. The other user must have already downloaded the Lumary App and registered an account.
Can I group multiple Lumary devices together? Yes, you can group multiple same-type devices by room, location, or however else you want. The same devices can be in multiple groups. From your main device list, click on one of the devices you want to group, press the "..." button on the top right for advanced settings, and click "Create Group". You'll be able to name a new group and choose which devices you'd like to group together.
My Lumary device has a funny name. How do I rename it? From your main device list, click on one of the devices you want to rename, press the "..." button on the top right for advanced settings, and click "Modify Device Name" (or "Modify Group Name"). You'll then be able to choose a more familiar name.
What's the wireless range? The range of your home Wi-Fi is heavily dependent on your home router and the conditions of the room. Check with your router specifications for exact range data.
What should I do if the device appears offline or is unreachable? Make sure your Wi-Fi router is online and in range. Check that you have the latest Lumary functionality by clicking "Check for firmware update" in your device settings. Try turning off the device, clearing the application cache, rebooting the router, and then turning the device back on after one minute. Check the device status after five minutes.
How many devices can I control?
- Maximum number of timers per single device: 30
- Maximum number of devices per single home: 120
- Maximum number of Tap-to-Run per single home: 100
- Maximum number of Automations per single home: 100
- Maximum number of tasks per Tap-to-Run: 150
- Maximum number of tasks per Automation: 150
- Maximum number of conditions per Automation: 10
- Maximum number of mobile devices that can simultaneously log in to an account: 200
- Maximum number of Homes per single App account: 20
- Maximum number of home members per single home: 20
- Maximum number of rooms per single home: 20
- Maximum number of devices per single room: 50
- Maximum number of device groups per single home: 20
- Maximum number of device groups that can be shared with other users: 20
- Maximum number of devices that can be shared with other users: 20
- Maximum number of App accounts that can be invited by other homes: 20
What should I do when I find a problem with the purchased product? Please email support@lumary.tech with your Amazon order ID. Lumary is dedicated to ensuring 100% satisfaction and will be happy to exchange the product if there is a problem.

How do I reset the device?

If the device is connected to the network, press and hold the control button for 5s; the indicator light will flash rapidly and enter the network state.

To reconnect to Wi-Fi:

Easy Mode: Reset the device through the wall switch: on - off - on - off - on. The indicator will blink rapidly white.
AP Mode: Reset again (press switch on - off - on - off - on). The indicator will blink slowly white.

Important Information

Troubleshooting

Can't connect to your Wi-Fi network: Make sure you entered the correct Wi-Fi password during setup. Check for any Internet connection problems. If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.

Parameter Information

Name	Lumary Smart Floating Gimbal Light
Model	US-GL4B-1
Input Voltage	100-130VAC, 60Hz
Wattage	7W
Color Temperature	RGB +Tunable White (2700K-6500K)
CRI	90
Lumens	550lm
Beam Angle	26°
Rated Life	25000h

Certifications: FC ♻️ RoHS ? ? Intertek 5000487

FCC ID: 2A5WDADS4FGSTRGBCW

Made in China

CAUTION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Voice Control Guide

Name and Control Each Device by Voice

Works with: ?️ Alexa, ?️ Hey Google

Voice Control Quick Guide for Amazon Alexa

1. Log in to Lumary APP, tap the smart device and enter into its settings by clicking "..." in the top right corner.

2. Tap "Alexa" in Third-party Control.

3. Tap "Sign In With Amazon".

4. Tap "Allow".

5. Linked successfully. When adding a new device, there is no need to link again; just discover the new device in Alexa.

Screenshots Description: Shows the app interface for linking Lumary with Amazon Alexa, including signing in and granting permissions.

Examples of what you can say:

"Alexa, discover my devices."
"Alexa, turn on the bedroom light."
"Alexa, set the bedroom light to orange."
"Alexa, turn off the coffee machine."
"Alexa, set the living room to 50%."
"Alexa, dim porch light."

*Some commands require compatible devices.

Voice Control Quick Guide for Google Assistant

1. Log in to Lumary app, tap the smart device and enter into its settings by clicking "..." in the top right corner.

2. Tap "Google Assistant" in Third-party Control.

3. Tap "Link with Google Assistant".

4. Click "Agree and link".

5. Linked successfully. When adding a new device, there is no need to link again; just discover the new device in Google Home.

Screenshots Description: Shows the app interface for linking Lumary with Google Assistant, including agreeing to permissions and granting control.