Lumary Smart Recessed Light User Manual

Introduction

Thank you for choosing Lumary products. This manual will guide you through setting up and using your Lumary Smart Recessed Light. Download the Lumary App to manage your devices from your phone and tablet, connect to your home Wi-Fi, and control multiple devices with ease. Lumary is a professional smart lighting producer committed to providing top-tier service and continuously optimizing its applications and products.

Product & Notes

What's in the Box

The package contains the following items:

• Lumary Smart User Manual
• Lumary 4" or 6" Ultra-thin Downlight

Package Contents Diagram Description: The diagram shows two circular light fixtures labeled A and B, a J-Box Driver labeled C, three nuts labeled D, and a circular hole cut-out template labeled E.

Get Ready

• Know your Wi-Fi network name and password.
• Ensure your mobile device is running iOS 13.3 or higher and Android 9.0 or higher.
• Make sure you are connecting to a 2.4GHz Wi-Fi network. Lumary products cannot connect to 5GHz networks.

Installation Instructions

IMPORTANT: Read all instructions before installing fixtures. Retain for future reference.

SAFETY: For your safety, this fixture must be wired in accordance with local electrical codes and ordinances. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF from the electrical panel before starting installation or attempting any maintenance. Indoor installation only.

Pre-Installation

1. Turn power OFF from the electrical panel before starting installation.
2. Locate a suitable position for the fixture and open a hole according to the cut-hole dimensions (refer to Hole Cut Table for appropriate size).
3. Run electrical wire from the switch (power supply) through the mounting hole, using NMD90 Romex.

Driver Wiring

New construction applications: Hardwire box shall be firmly secured to studs, joists, or similar fixed structural units.

Remodel applications: The hardwire box does not require firm securing after the mounting plates, studs, joists, or structural units have been concealed. Junction box suitable for a maximum of 5 No 12 AWG or 8 No 14 AWG Conductors.

Installation Steps

1. Turn off the power before installation. Remove the existing fixture if applicable. Determine the location and necessary hole cutout diameter using the supplied table and cut the ceiling hole with the listed approximate diameter.

   Diagram Description (Fig1): Shows a table with "HOLE SIZE" for 4-inch (4 21/64" or 110mm) and 6-inch (6 19/64" or 160mm) fixtures. An illustration depicts a hand using a tool to cut a circular hole in a ceiling.

2. Open the J-Box cover and remove the appropriate knockout(s) on the side panel. Install the appropriate cable clamp(s) (not included) and insert the electrical supply cable through the cable clamp. Connect the supply wires to the fixture wires using 3 connectors. Attach white to white, black to black, and copper to the ground wire.

   Diagram Description (Fig2): Illustrates the J-Box wiring. Labels indicate: Black wire connected to L (Line), White wire connected to N (Neutral), and Copper wire connected to G (Ground).

3. Insert the J-Box through the mounting hole and secure it. Connect the fixture power cable to the J-Box.

   Diagram Description (Fig3): Shows the J-Box being inserted into the ceiling hole and the fixture's power cable being connected to the J-Box.

4. Push the spring-loaded clips into the mounting hole upwards and insert the fixture into it. Release the clips, and the fixture will be pulled flush to the ceiling.

   Diagram Description (Fig4): Depicts the fixture's spring clips being pushed up to allow insertion into the ceiling, and then releasing to hold the fixture in place.

5. Turn on the power after installation and check that the fixture is working correctly.

   Diagram Description (Fig5): Shows the installed fixture powered on and illuminated.

Application Connection

1. Find and install the "Lumary" App on the App Store or Google Play.

   Diagram Description: Screenshots show the Lumary App listing in the Apple App Store and Google Play Store, with options to download or install.

2. Register a Lumary account.

   Diagram Description: Screenshots show the Lumary App login screen, prompting for email address, password, and region/country selection.

3. Connect the device.

   NOTE: Lumary's products can't connect to 5GHz networks.

   Steps:

   • Enable Bluetooth on your mobile device to add Wi-Fi devices easily.
   • When the device is powered on without a network connection, ensure the light is in pairing mode (breathing or blinking).
   • Open the Lumary App, tap "+" in the top corner of the Devices screen, and select "Add Device" to confirm pairing.
   • If the device is not pairing, use the wall switch to reset it: turn it off, then on, then off, then on, then off, then on (on-off-on-off-on sequence).
   • Find the device, choose your Wi-Fi network, enter the password, and press "Next". Click "Add", wait patiently, then click "Done" to successfully add the device to the App.
   • Alternatively, open the Lumary App, tap "+", choose "Lighting", select "Light Source (BLE + Wi-Fi)", and then select "AP Mode" or "EZ Mode" in the upper right corner.

   Diagram Description: Screenshots show the Lumary App interface for adding devices, including categories like "Electrical", "Lighting", "Sensors", and specific device types like "Light Source (BLE+Wi-Fi)". Another screenshot shows the "Enter Wi-Fi Information" screen for selecting a network and entering a password, with a note about 5GHz networks. A final screenshot shows multiple devices successfully added.

Troubleshooting

1. Can't connect to your Wi-Fi network: Make sure you entered the correct Wi-Fi password during setup. Check for any internet connection problems. If the Wi-Fi signal is too weak, reset your Wi-Fi router and try again.
2. If you fail to bind: You may need two phones. Use one to set up a hotspot and the other to connect to the hotspot and add the device through the app. If the device is successfully added, the problem is likely with your router. Check your router settings for MAC and DHCP restrictions. Lumary's products do not support 5GHz networks.
3. If you have any questions: Contact Lumary via email at support@lumary.tech or leave a message on their official social media accounts.
4. Note: To ensure stable product output, 4-inch and 6-inch light sources and their power supply boxes cannot be mixed. Please follow the corresponding model for connections.

How do I reset the device?

To reconnect to Wi-Fi, reset the device through the wall switch using the sequence: on - off - on - off - on.

• Resetting once (on-off-on-off-on) reaches Easy Mode, indicated by a rapidly blinking white light. Refer to connect in Easy Mode.
• Resetting again (on-off-on-off-on) reaches AP Mode, indicated by a slowly blinking white light. Refer to connect in AP Mode.

What should I do if the device appears offline or is unreachable?

Ensure your Wi-Fi router is online and within range. Check for the latest Lumary functionality by clicking "Check for firmware update" in your device settings. Try turning off the device, clearing the application cache, rebooting the router, turning the device back on after one minute, and checking the device status after five minutes.

Group Control

1. Log in to the Lumary App, tap the smart device, and enter its settings. Click the "..." icon in the top right corner.

   Diagram Description: Screenshots show the Lumary App interface. The first shows a list of devices, and tapping one leads to a detail screen with a "..." icon in the top right.

2. Click "Create Group", then select the devices you want to group, and save.

   Diagram Description: Screenshots show the Lumary App menu with "Create Group" selected, followed by a screen to add devices to the group, and a final screen to name the group.

3. You can reset the group name and save it. The group can then control the selected devices.

   Diagram Description: Screenshots show the process of naming a group and then the main Lumary App screen displaying the created group with its controlled devices.

Beacon Remote Control

The Lumary remote control allows you to manage your smart lights:

• ON/OFF [power]
• Night Light [night-light]
• 7 Colors
• Brightness- [brightness-down]
• K- [temp-down] RGB K+ [temp-up]
• Brightness+ [brightness-up]
• Temperature+
• Group A [group A]
• Group B [group B]
• Scene [scene]
• Group C [group C]
• Group D [group D]

Diagram Description: An illustration of a remote control with labels pointing to each button: ON/OFF, Night Light, 7 Colors, Brightness-, K- (Color Temperature Decrease), RGB, K+ (Color Temperature Increase), Brightness+, Temperature+, Group A, Group B, Scene, Group C, Group D. The Lumary logo is at the bottom.

Remote Control Pairing

Note: Not all devices are compatible with the remote control. Downlights manufactured after January 2022 (models A/B/C/D/F) are compatible.

If you require more detailed information, please contact support@lumary.tech.

1. The device is powered by 2xAAA dry batteries.
2. First, the light needs to be bound to the Lumary App.
3. Use the wall switch to disconnect the power for 5 seconds, then turn the power back on. The light and the remote control should be in pairing status.
4. Long press any key on the remote control (A/B/C/D) as needed until the light blinks to indicate successful pairing. If desired devices are not fully paired, press and hold the group button again until all devices are paired successfully. If it takes more than 1 minute, repeat steps 3-4.

FAQ

1. Why does flickering occur with Lumary products? Lumary products are factory set to default network configuration. If the device is not connected to the network, it will flash for three minutes each time it is powered on. If it is connected, it will stop flashing and automatically connect when switched off and on via the wall switch after 15 seconds.
2. What should I do if the device appears offline or is unreachable? Ensure your Wi-Fi router is online and in range. Check for the latest Lumary functionality by clicking "Check for firmware update" in your device settings. Try turning off the device, clearing the application cache, rebooting the router, turning the device back on after one minute, and checking the device status after five minutes.
3. How do I reset the device? To reconnect to Wi-Fi, reset the device through the wall switch using the sequence: on - off - on - off - on.
   • Resetting once (on-off-on-off-on) reaches Easy Mode, indicated by a rapidly blinking white light. Refer to connect in Easy Mode.
   • Resetting again (on-off-on-off-on) reaches AP Mode, indicated by a slowly blinking white light. Refer to connect in AP Mode.
4. How many devices can I control?
   • Maximum number of timers per device: 30
   • Maximum number of devices per home: 120
   • Maximum number of Tap-to-Run per home: 100
   • Maximum number of Automations per home: 100
   • Maximum number of tasks in Tap-to-Run: 150
   • Maximum number of tasks in Automation: 150
   • Maximum number of conditions in Automation: 10
   • Maximum mobile devices logged in simultaneously: 200
   • Maximum Homes per App account: 20
   • Maximum home members per home: 20
   • Maximum rooms per home: 20
   • Maximum devices per room: 50
   • Maximum devices per device group: 100
   • Maximum device groups per home: 20
   • Maximum device groups shared with other users: 20
   • Maximum devices shared with other users: 20
   • Maximum App accounts invited by other homes: 20
5. What should I do if I find a problem with the purchased product? Please email support@lumary.tech with your Amazon order ID. Lumary is dedicated to ensuring satisfaction and will exchange the product if there is a problem.

Parameter Information

Certifications: FC, RoHS, ETL LISTED (Intertek)

FCC ID: 2ANDL-CBU

Made in: China

CAUTION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Voice Control Guide

Name and Control Each Device by Voice

Works with Alexa

Works with Hey Google

Work With Amazon Alexa

Steps:

1. Log in to the Lumary App, tap the smart device, and enter its settings. Click the "..." icon in the top right corner.
2. Tap "Alexa" in the Third-party Control section.
3. Tap "Sign In With Amazon".
4. Tap "Allow".
5. Linking is successful. When adding a new device, there is no need to link again; simply discover the new device in Alexa.

Example Commands:

• "Alexa, discover my devices."
• "Alexa, turn on the bedroom light."
• "Alexa, set the bedroom light to orange."
• "Alexa, turn off the coffee machine."
• "Alexa, set the living room to 50%."
• "Alexa, dim porch light."

*Some commands require compatible devices.

Diagram Description: Screenshots show the Lumary App linking to Amazon Alexa. This includes selecting Alexa in third-party controls, signing into Amazon, and confirming permissions. The final screen shows successful linking with example voice commands.

Work With Google Assistant

Steps:

1. Log in to the Lumary App, tap the smart device, and enter its settings. Click the "..." icon in the top right corner.
2. Tap "Google Assistant" in the Third-party Control section.
3. Tap "Link with Google Assistant".
4. Click "Agree and link".
5. Linking is successful. When adding a new device, there is no need to link again; simply discover the new device in Google Home.

Example Commands:

• "Hey Google, turn on all the lights in my bedroom."
• "Hey Google, turn off the light."
• "Hey Google, set the bedroom light to orange."
• "Hey Google, turn off the coffee machine."
• "Hey Google, set the living room to 50%."
• "Hey Google, dim porch light."

*Some commands require compatible devices.

Diagram Description: Screenshots show the Lumary App linking to Google Assistant. This includes selecting Google Assistant in third-party controls, linking the account, and agreeing to permissions. The final screen shows successful linking with example voice commands.

Contact Information

If you have any questions about use and operation, you can contact Lumary:

Customer Service Email: support@lumary.tech

You can also search for Lumary's account name and enter the URL on social media platforms or scan QR codes to find them quickly:

• Facebook: US-Smart Home (facebook.com/Lumary-Smart-Lighting-102878658675054)
• YouTube: Lumary Official (youtube.com/channel/UCcEQnWxockzsPwyPOfSppug)
• Instagram: Lumary Smart Home (instagram.com/lumarysmartlights/)
• Twitter: Lumary @Lumarysmarthome (twitter.com/Lumarysmarthome)
• Pinterest: Lumary Smart Home (pinterest.com/LumarySmartHome/)

Note: QR codes from the original document are excluded as per instructions.

Support

Can't connect? Need help?

Having an easy talk with Lumary support before returning the product can fix a problem more quickly.

Lumary support: support@lumary.tech

Visit us at:

www.lumary.tech

www.lumarysmart.com