Assembly Instructions
Important Warnings
- CHOKING HAZARD: Small Parts. Not for children under 3 years. Adult assembly required.
- Tip: Although not required, it is recommended that a drill be used to help ease the assembly process, as some holes are not pre-drilled.
Product Overview
This document provides assembly instructions for the Latitude Run Collins Modern 6-Drawer Dresser. The dresser has overall dimensions of approximately 57.09 inches in width, 32.28 inches in height, and 17.72 inches in depth.
Part Identification
The following parts are included in the package:
- 01: Right side panel
- 02: Left side panel
- 03: Divider
- 04: Top
- 05: Bottom/Base
- 06: Right Side of Drawer
- 07: Left Side of Drawer
- 08: Back of Drawer
- 09: Drawer Support
- 10: Base of Drawer
- 11: Back Panel
- 12: Drawer front right
- 13: Left front drawer
List of Pieces
| Code | Description | Amount | Length (in.) | Width (in.) | Thickness (in.) | Box |
|---|---|---|---|---|---|---|
| 01 | Right side panel | 1 | 24.25 | 17.60 | .59 | B |
| 02 | Left side panel | 1 | 24.25 | 17.60 | .59 | B |
| 03 | Divider | 1 | 24.25 | 16.85 | .59 | B |
| 04 | Top | 1 | 56.97 | 17.60 | .59 | A |
| 05 | Bottom/Base | 1 | 56.97 | 17.60 | .59 | A |
| 06 | Right Side of Drawer | 6 | 15.75 | 5.51 | .59 | B |
| 07 | Left Side of Drawer | 6 | 15.75 | 5.51 | .59 | B |
| 08 | Back of Drawer | 6 | 25.39 | 5.51 | .59 | B |
| 09 | Drawer Support | 6 | 15.12 | 3.15 | .59 | B |
| 10 | Base of Drawer | 6 | 25.55 | 15.67 | .12 | A |
| 11 | Back Panel | 2 | 56.50 | 12.40 | .12 | A |
| 12 | Drawer front right | 3 | 27.60 | 7.83 | .59 | A |
| 13 | Left front drawer | 3 | 27.60 | 7.83 | .59 | A |
Hardware
| Code | Description | Amount |
|---|---|---|
| PM | Cam Screws | 18 |
| TM | Cam Locks | 18 |
| PE18 | Screw 5x40 | 18 |
| PC16 | Screw 5,0X30 | 8 |
| C1 | Dowel 6x30mm | 84 |
| PC3 | Screw 3,5x14 | 52 |
| PF2 | Screw 3,5x14 | 12 |
| PR1 | Nail 10x10 | 41 |
| CM4 | 400mm metal slide set | 6 |
| CM4A | Right Drawer slide | - |
| CM4B | Left drawer slide | - |
| CM4C | Metallic slide for left sided panel | - |
| CM4D | Metallic slide for right sided panel | - |
| PX | Handle 70mm | 6 |
| TP1 | Screw cap cover 19mm | 18 |
| TP2 | Screw cap cover 13mm | 18 |
| P1 | Metal foot tube | 2 |
| P2 | Central foot | 1 |
| CZ3 | Allen key | 1 |
| PH | Finishing profile | 2 |
Helpful Tips
Installing Cam
Identify the arrow on the cam. The arrow MUST point toward the hole in the edge of the panel. Push the cam all the way down into the hole.
Cam and Dowel Alignment
Ensure the cam arrow points toward the hole and insert the cam dowel into its hole. Make sure the pieces join together.
Tightening Cam
Use a screwdriver to turn the cam clockwise until fully tightened. This is slightly more than half a turn.
Assembly Steps
Step 1: Drawer Preassembly (x6)
Assemble the drawer components: Attach drawer sides (06, 07) to drawer backs (08) and drawer supports (09) using dowels (C1). Then attach drawer fronts (12, 13) using cam screws (PM) and cam locks (TM).
Step 2: Drawers Mounting (x6)
Attach drawer slides (CM4A, CM4B) to the assembled drawer sides (07, 08) using cam screws (PE18), cam locks (CZ3), and screw caps (TP2). Ensure the wheels face the back of the drawer.
Step 3: Drawers Mounting (x6)
Attach drawer fronts (13) to the drawer body using cam locks (TM) and screw caps (TP1). Ensure correct alignment.
Step 4: Drawers Mounting (x6)
Attach drawer slides (CM4A, CM4B) to the main dresser frame using screws (PC3). Ensure the front of the slide aligns with the front of the frame. The QR code mentioned in the PDF links to a YouTube video for "K1 GLIDE RAIL" installation.
Important: Please ensure that these screws are completely screwed in. Failure to do so could cause issues when installing the drawer.
Note: Wheels should always be towards the back of the drawers.
Step 5: Drawer Final Assembly
Attach handles (PX) to the drawer fronts (12, 13) using screws (PF2). Use the indent on the drawer front as a guide for placement/installation of the handles.
Step 6: Preassembly of Parts
Insert dowels (C1) into panels (01), (02), (03), and (04). Attach panels (01) and (02) to the base (05) using cam screws (PM) and dowels (C1).
Step 7: Attaching Slides to Side Panels
Attach drawer slides (CM4C, CM4D) to the side panels (01, 02) using screws (PC3). Ensure correct orientation (front/back, up/down) as indicated in the diagrams. The diagrams show detailed views of correct hole locations for the PC3 screws.
Step 8: Product Assembly
Assemble the main frame by attaching side panels (01, 02) and dividers (03) to the base (05) using cam screws (PE18), cam locks (CZ3), and screw caps (TP2).
Step 9: Attaching Top Panel
Attach the top panel (04) to the assembled frame using cam locks (TM) and screw caps (TP1). Ensure correct alignment.
Step 10: Attaching Back Panel
Carefully place the dresser on its front. Align the back panel (11) and secure it using nails (PR1) and the small panel (PH). Ensure the back panel is square to the sides and top before nailing to prevent drawers from appearing crooked.
Attention: Ensure that when nailing the back parts in place, that it is being nailed as straight as possible to the top and sides. Failure to do so can make the drawers appear crooked.
Note: It is essential to place the furniture straight/squared to avoid problems with the functioning and alignment of the Drawers and Doors.
Step 11: Installing Legs
Attach the legs (P1, P2) to the base (05) using screws (PC16) and (PC3). Use the pre-marked indents as a guide for screw placement.
Step 12: Drawer Installation
Insert the assembled drawers into the dresser frame by aligning the slides. Close the drawer to lock the clip.
Weight Information: Type A: 35 Kg (77.16 lb), Type B: 6 Kg (13.23 lb)
Anti-tipping Installation
WARNING - Anti-Tip Advisory: Potential of serious fatal crushing injuries may occur from furniture tip-over. To help prevent tip-over:
- ALWAYS INSTALL the tip-over restraint that came with your furniture. This tip-over restraint only reduces but does NOT completely eliminate the risk of tip-over.
- ALWAYS Place the heaviest items in the lowest/bottom drawer.
- NEVER place heavy objects on top of this product.
- NEVER allow children to scale/climb/hang on the drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
ATENCION - Aviso antivuelco: Pueden producirse lesiones graves por aplastamiento mortales debido al vuelco de los muebles. Para ayudar a prevenir vuelcos:
- SIEMPRE INSTALE el sistema de retención que viene con sus muebles. Este sistema antivuelco solo reduce pero NO elimina por completo el riesgo de vuelco.
- SIEMPRE coloque los artículos más pesados en el cajón más bajo /inferior.
- NUNCA coloque objetos pesados encima de este producto.
- NUNCA permita que los niños escalen, trepen o se cuelguen de los cajones, puertas o estantes.
- NUNCA abra más de un cajón a la vez.
Installation Note: Do not turn the DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY ANTI-TIPPING to a wall stud, go to your local hardware store for proper hardware.
Installation Steps:
- Compress the wings of the anchor before inserting.
- Insert the chuck into the hole of the base material.
- Position the object over the bushing and secure it with a screw.
Important: The minimum length of the screw must be the bushing length + object thickness that will be fixed. To guarantee the wing expansion function of the bushing, after the screw head is at the object to be fixed, one must continue to rotate the screw until maximum torque is reached.
Piercing the base material: Pierce the base material with a 0.39 in. drill.
Cleaning Instructions
To Remove the printed number, apply a small amount of Glass Cleaner or Hand sanitizer and wipe with a paper towel.
