Latitude Run Catoe Kahanuola Modern 6-Drawer Dresser Assembly Instructions
Important Safety Information
⚠️ Warning: CHOKING HAZARD - Small Parts. Not for children under 3 years. Adult assembly required.
Product Overview
This document provides instructions for assembling the Catoe Kahanuola Modern 6-Drawer Dresser by Latitude Run. The assembled dresser measures approximately 31.89 inches in height, 17.72 inches in depth, and 52.56 inches in width.
Assembly Tip: It is recommended to use a power drill to assist with assembly, as some holes may not be pre-drilled.
Workspace Recommendation: Use the original packaging box as a base for your workspace to help prevent damage during assembly.
Part Identification
Identify all parts before beginning assembly. The following components are included:
| Code | Description | Description (Portuguese) | Amount | Length (in.) | Width (in.) | Thickness (in.) | Box |
|---|---|---|---|---|---|---|---|
| 01 | Right side panel | Lateral direita | 1 | 30.98" | 17.60" | .59" | A |
| 02 | Left side panel | Lateral esquerda | 1 | 30.98" | 17.60" | .59" | A |
| 03 | Divider | Divisória | 1 | 26.57" | 17.60" | .59" | A |
| 04 | Top | Tampo | 1 | 52.56" | 17.60" | .59" | A |
| 05 | Bottom/Base front | Base frontal | 1 | 51.30" | 3.78" | .59" | A |
| 06 | Bottom/Base Rear | Base traseira | 1 | 51.30" | 3.78" | .59" | A |
| 07 | Front skirting | Rodapé frontal | 1 | 51.30" | 3.78" | .59" | A |
| 08 | Internal skirting | Rodapé interno | 1 | 16.30" | 3.78" | .59" | A |
| 09 | Drawer front | Frente de gaveta | 6 | 25.04" | 8.58" | .59" | A |
| 10 | Right Side of Drawer | Lateral de gaveta direita | 6 | 15.75" | 5.51" | .59" | A |
| 11 | Left Side of Drawer | Lateral de gaveta esquerda | 6 | 15.75" | 5.51" | .59" | A |
| 12 | Back of Drawer | Cabeceira de gaveta | 6 | 23.19" | 5.51" | .59" | A |
| 13 | Drawer Support | Sarrafo de gaveta | 6 | 15.12" | 3.15" | .59" | A |
| 14 | Base of Drawer | Fundo de gaveta | 6 | 23.70" | 15.67" | .12" | A |
| 15 | Back Panel | Costa | 2 | 52.17" | 13.62" | .12" | A |
Hardware List
The following hardware is required for assembly:
| Code | Description | Amount |
|---|---|---|
| PM 30945 | Cam Screws | 24 |
| TM 30950 | Cam Locks | 24 |
| PE18 75515 | Screw 5x40 | 16 |
| C1 1802 | Dowel 6x30mm | 88 |
| PC3 4214 | Screw 3.5x14 | 52 |
| PF2 25827 | Screw 3.5x14 | 12 |
| PR1 107 | Nail 10x10 | 40 |
| PR2 108 | Nail 12x12 | 6 |
| CM4 | 400mm metal slide set | 6 |
| CM4A | Right Drawer slide | - |
| CM4B | Left drawer slide | - |
| CM4C | Metallic slide for left sided panel | - |
| CM4D | Metallic slide for right sided panel | - |
| SD 1901 | Shoe block | 6 |
| PX | Handle | 6 |
| TP1 | Screw cap cover 19mm | 12 |
| CZ3 58788 | Allen key | 1 |
| PH | Finishing profile | 2 |
| CG 899 | Angle bracket | 1 |
Helpful Tips
- Installing Cam: Identify the arrow on the head of the cam. The arrow MUST point toward the hole in the edge of the panel. Push the cam all the way down into the hole.
- Cam and Dowel Alignment: Ensure the arrow on the cam points toward the hole and insert the cam dowel into the hole. Make sure the pieces join together securely.
- Tightening Cam: Use a screwdriver to turn the cam clockwise until fully tightened. This is typically slightly more than half a turn.
Assembly Steps
Step 1: Drawer Preassembly (Repeat 6 times)
1A: Attach part 10 (Right Side of Drawer) to the drawer front and back panels.
1B: Attach part 11 (Left Side of Drawer) to the drawer front and back panels.
1C: Attach part 13 (Drawer Support) to the drawer sides.
1D: Attach part 12 (Back of Drawer) to the drawer sides.
1E: Attach part 09 (Drawer front) to the assembled drawer sides using PM screws and C1 dowels. Ensure screws are inserted correctly, with the head flush and the shaft fully engaged.
Step 2: Drawers Mounting (Repeat 6 times)
Attach PE18 screws and CZ3 Allen key to the drawer sides. Secure the drawer sides (11, 14) to the drawer front (09) and back (12) using PC3 screws.
Step 3: Drawers Mounting (Repeat 6 times)
Insert TM cam locks and TP1 screw caps into the drawer assembly. Secure the drawer sides (10, 11) to the drawer front (09) and back (12) using TM cam locks. Ensure the cam lock is turned to secure the connection.
Step 4: Main Body Assembly
Attach drawer slides (CM4A, CM4B) to the side panels (01, 02) using PC3 screws. Ensure the wheels of the slides are always positioned towards the back of the dresser. Important: Ensure all screws are completely screwed in to avoid issues during drawer installation.
Step 5: Drawer Final Assembly
Attach PX handles to the drawer fronts (09) using PF2 screws. Use the pre-drilled indentations on the drawer front as a guide for handle placement and installation.
Step 6: Preassembly of Parts
Attach CM4C/CM4D drawer slides to the side panels (01, 02) using C1 dowels and PM screws. Ensure correct hole alignment for the PC3 screws.
Step 7: Preassembly of Parts
Attach CM4C/CM4D drawer slides to the divider panel (03) using C1 dowels and PM screws. Ensure correct hole alignment for the PC3 screws.
Step 8: Preassembly of Parts
Insert C1 dowels into the designated holes on the base panels (05, 06, 07, 08).
Step 9: Preassembly of Parts
Insert PM screws into the designated holes on the top panel (04).
Step 10: Product Assembly
Connect the side panels (01, 02) and the divider (03) to the base panels (04, 05, 07) using TM cam locks. Ensure the cam locks are properly tightened to secure the structure.
Step 11: Product Assembly
Attach drawer slides (PE18, CZ3) to the side panels (02, 03) and base panels (05, 06, 07) using the provided hardware.
Step 12: Product Assembly
Attach drawer slides (PE18, CZ3) to the side panels (06, 08) and base panels (05, 07) using the provided hardware.
Step 13: Product Assembly
Connect the side panel (01) and base panels (04, 05, 07) using TM cam locks. Ensure the cam locks are properly tightened.
Step 14: Product Assembly
Attach SD shoe blocks and CG angle brackets to the bottom of the dresser using PR2 screws and PC3 screws, respectively. Ensure secure attachment.
Step 15: Product Assembly
1ST: Position the back panels (15) onto the rear of the dresser. Ensure the panels are aligned correctly with the top and sides.
2ND: Carefully place the furniture on its front, ideally on the original packaging box, to protect it while attaching the back panels. Use PH screws to secure the back panels.
3RD: After ensuring the back panel is squared to the side and top, use PR1 nails to secure the back panel in place. Attention: Ensure that when nailing the back parts in place, they are nailed as straight as possible to the top and sides. Failure to do so can make the drawers appear crooked.
Alignment Note: It is essential to place the furniture straight/squared to avoid problems with the functioning and alignment of the drawers and doors. ✔️ (Correct) ❌ (Incorrect)
Step 16: Drawer Installation
Insert the drawer slides into their corresponding profiles on the dresser and close the drawers to finish locking the clips. The table indicates weight capacities or component weights: A (35 kg / 77.16 lb), B (6 kg / 13.23 lb).
Anti-tipping Installation
WARNING - Anti-Tip Advisory: Potential of serious fatal crushing injuries may occur from furniture tip-over. To help prevent tip-over:
- ALWAYS INSTALL the tip-over restrain that came with your furniture. This tip-over restraint only reduces but does NOT completely eliminate the risk of tip-over.
- ALWAYS place the heaviest items in the lowest/bottom drawer.
- NEVER place heavy objects on top of this product.
- NEVER allow children to scale/climb/hang on the drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
ADVERTENCIA - Aviso antivuelco: Pueden producirse lesiones graves por aplastamiento mortales debido al vuelco de los muebles. Para ayudar a prevenir vuelcos:
- SIEMPRE INSTALE el sistema de retención que viene con sus muebles. Este sistema antivuelco solo reduce pero NO elimina por completo el riesgo de vuelco.
- SIEMPRE coloque los artículos más pesados en el cajón más bajo /inferior.
- NUNCA coloque objetos pesados encima de este producto.
- NUNCA permita que los niños escalen, trepen o se cuelguen de los cajones, puertas o estantes.
- NUNCA abra más de un cajón a la vez.
Installation Instructions:
Note: Do not turn the DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY ANTI-TIPPING to a wall stud, go to your local hardware store for proper hardware.
General Steps:
- Compress the wings of the anchor before inserting.
- Insert the anchor (BG) into the wall or a pre-drilled hole. Pierce the base material with a 0.39 in. drill.
- Position the furniture or bracket (SF) over the anchor and secure it with a screw (PF4 or PC10).
Important: The minimum length of the screw must be the bushing length plus the object thickness that will be fixed. To guarantee the wing expansion function of the bushing, after the screw head is at the object to be fixed, continue to rotate the screw until maximum torque is reached.
Hardware for Anti-tipping: SF (Mounting bracket, 2), ANY (Clamp, 1), PC10 (Screw 4.5x50, 2), PF4 (Screw 3.5x16 BO, 2), BG (Anchor sleeve, 2).
Care and Maintenance
To remove printed numbers or markings from the surfaces, apply a small amount of glass cleaner or hand sanitizer to a paper towel and wipe the surface.
