Parts List / Liste des Pièces
| Part # | Name (English) | Name (French) | Quantity |
|---|---|---|---|
| 1 | Front left foot | Pied gauche avant | X1 |
| 2 | Rear left foot | Pied gauche arrière | X1 |
| 3 | Rear right foot | Pied droit arrière | X1 |
| 4 | Front right foot | Pied droit avant | X1 |
| 5 | Left inner side plate | Plaque intérieure gauche | X1 |
| 6 | Right inner side plate | Plaque intérieure droite | X1 |
| 7 | Outer rear plate | Plaque arrière extérieure | X1 |
| 8 | Inner rear plate | Plaque arrière intérieure | X1 |
| 9 | Middle rear plate | Plaque arrière moyenne | X1 |
| 10 | Top panel sticker strip | Bande adhésive du panneau supérieur | X1 |
| 11 | Pull-down horizontal strip | Bande horizontale à tiroir | X4 |
| 12 | Front bottom strip | Bande avant inférieure | X1 |
| 13 | Back panel | Panneau arrière | X1 |
| 14 | Top panel | Panneau supérieur | X1 |
| 15 | Drawer front panel | Panneau avant du tiroir | X5 |
| 16 | Right side panel of the drawer | Panneau latéral droit du tiroir | X5 |
| 17 | Left side panel of the drawer | Panneau latéral gauche du tiroir | X5 |
| 18 | Drawer pull-down strip | Bande à tiroir à descente | X5 |
| 19 | Drawer bottom panel | Panneau inférieur du tiroir | X5 |
| 20 | Drawer back panel | Panneau arrière du tiroir | X5 |
| 21 | Inner Rear Heavy Plate | Plaque lourde intérieure arrière | X1 |
| 22 | Inner Rear Heavy Plate | Plaque lourde intérieure arrière | X1 |
| 23 | Inner rear plate | Plaque arrière intérieure | X1 |
Hardware / Matériel & Assembly Tools
| Code | Description | Quantity |
|---|---|---|
| A | 6*35 mm screw | 67+2 |
| B | 6*30 mm screw | 36+2 |
| C | 15*10 mm screw | 67+2 |
| D | 3*12 mm screw | 50+2 |
| E | 4*25 mm screw | 12+1 |
| F | L-shaped bracket | x1 |
| G | 4*30 mm screw | 27+2 |
| H | Allen key | x1 |
| I | 4*18 mm screw | x5 |
| CL | Drawer slide (left) | x5 |
| CR | Drawer slide (right) | x5 |
| DL | Drawer slide (left) | x5 |
| DR | Drawer slide (right) | x5 |
| Screwdriver (Tool) | ||
| Hammer (Tool) |
Assembly Steps
Step 1 / Étapes 1
Attach the two long side panels (1 and 2) to the two shorter base panels (3 and 4) using sixteen 'A' screws (6*35 mm).
Diagram shows panels 1 and 2 positioned vertically, connected to horizontal panels 3 and 4 at their ends, secured with screws.
Step 2 / Étapes 2
Attach the inner side plates (5 and 6) to the base structure. Use twelve 'B' screws (6*30 mm) and sixteen 'C' screws (15*10 mm) as shown.
Diagram shows panels 5 and 6 being attached to the sides of the structure from Step 1, using screws B and C.
Step 3 / Étapes 3
Attach five 'CL' drawer slides to the inner side plates (5 and 6). Use fifteen 'D' screws (3*12 mm) to secure them. Ensure the slides are oriented correctly with the rollers facing downwards and towards the front.
Diagram shows the 'CL' slides being screwed onto the inner faces of panels 5 and 6, with specific hole alignments indicated.
Step 4 / Étapes 4
Attach five 'CR' drawer slides to the inner side plates (5 and 6). Use fifteen 'D' screws (3*12 mm) to secure them. Ensure the slides are oriented correctly with the rollers facing downwards and towards the front.
Diagram shows the 'CR' slides being screwed onto the inner faces of panels 5 and 6, mirroring the placement of the 'CL' slides.
Step 5 / Étapes 5
Reinforce the main frame by attaching panels 1, 2, 5, and 6 to the base structure (panels 3 and 4) using twenty-two 'A' screws (6*35 mm).
Diagram shows additional screws being inserted into the base and side panel connections, reinforcing the structure.
Step 6 / Étapes 6
Attach the inner rear plate (23) to the side panel (8) using two 'B' screws (6*30 mm). Repeat for the other side panel. Then, attach another inner rear plate (23) to the assembled side panels using four 'E' screws (4*25 mm).
Diagram shows panels 23 being attached to panels 8, and then panels 8 with 23 attached being joined together.
Step 7 / Étapes 7
Assemble the main carcass. Connect the side panels (5, 6) to the front bottom strip (12) and front feet (1, 4). Attach the outer rear plate (7) and middle rear plate (9) to the side panels. Secure the pull-down horizontal strips (11) and the top panel sticker strip (10). Use eighteen 'B' screws (6*30 mm) and fourteen 'C' screws (15*10 mm).
Diagram shows the main frame being constructed with multiple panels and strips being attached to the side panels.
Step 8 / Étapes 8
Attach the inner rear plate (9) to the assembled carcass using eight 'C' screws (15*10 mm).
Diagram shows panel 9 being attached to the rear of the carcass, likely as a central support.
Step 9 / Étapes 9
Slide the back panel (13) into the grooves on the rear of the dresser carcass.
Diagram shows panel 13 being inserted downwards into pre-cut grooves on the back edges of the dresser frame.
Step 10 / Étapes 10
Attach the top panel (14) to the carcass. Use four 'A' screws (6*35 mm) from underneath and one 'F' bracket with an 'A' screw (6*35 mm) for reinforcement.
Diagram shows panel 14 being placed on top of the carcass, with screws inserted from below and a bracket attached for stability.
Step 11 / Étapes 11
Secure the top panel (14) from the inside using four 'B' screws (6*30 mm) and four 'C' screws (15*10 mm). Attach the top panel sticker strip (10) to the front edge of the top panel using two 'G' screws (4*30 mm).
Diagram shows screws being inserted from inside the carcass into the top panel, and the strip 10 being attached to the front of the top panel.
Step 12 / Étapes 12
Attach the anti-tip hardware (F) to the top rear of the dresser using four 'B' screws (6*30 mm). These will later be secured to the wall.
Diagram shows two L-shaped brackets (F) being screwed into the top rear edge of the dresser.
Step 13 / Étapes 13
For each of the five drawers, attach the drawer front panel (15) to the left side panel (17) and right side panel (16). Use five 'A' screws (6*35 mm) and one 'C' screw (15*10 mm) per drawer.
Diagram shows drawer front 15 being joined to side panels 16 and 17, secured with screws.
Step 14 / Étapes 14
For each of the five drawers, slide the drawer bottom panel (19) into the grooves of the side panels. Attach the drawer back panel (20) to the side panels using twenty 'C' screws (15*10 mm) and five 'G' screws (4*30 mm) per drawer.
Diagram shows panel 19 sliding into grooves and panel 20 being attached to the rear of the drawer assembly.
Step 15 / Étapes 15
Secure the drawer back panel (20) to the drawer assembly using four 'G' screws (4*30 mm) per drawer.
Diagram shows additional screws being inserted into the back panel of the drawer for extra security.
Step 16 / Étapes 16
Attach the 'DL' drawer slides to the left side of each drawer and the 'DR' drawer slides to the right side of each drawer. Use twenty 'D' screws (3*12 mm) in total for all five drawers.
Diagram shows the DL and DR slides being attached to the bottom outer edges of the drawer sides.
Step 17 / Étapes 17
Attach the drawer pull-down strips (18) to the front of each drawer using five 'I' screws (4*18 mm) per drawer.
Diagram shows the pull-down strips being screwed onto the front face of the drawer panels.
Step 18 / Étapes 18
Carefully insert the five assembled drawers into the dresser carcass, aligning them with the drawer slides.
Diagram shows the completed drawers being slid into the dresser frame.
Step 19 / Étapes 19
For safety and stability, it is suggested to secure the anti-tip accessories to the wall to prevent tipping, injury, and property damage.
Attention : Pour la sécurité et la stabilité, il est suggéré de fixer les accessoires anti-basculement au mur pour éviter le basculement, les blessures et les dommages matériels.
Installation Completed / Installation terminée
Diagram shows the fully assembled dresser with drawers inserted.
