IKEA BESTÅ TV Bench Assembly Instructions

Important Safety Information ⚠️

WARNING! Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Note: Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

Tools Required

• Phillips head screwdriver ?
• Flat head screwdriver ?
• Spirit level ?

Parts and Hardware

Identify all parts and hardware before starting assembly. Refer to the diagrams for visual identification.

• Feet: 6x (Part numbers: 114947, 115988)
• Screws: 12x (Part number: 130618), 2x (Part number: 113287), 4x (Part number: 109049), 16x (Part number: 116637)
• Cam Lock Housings: 4x (Part numbers: 130619, 130722, 141027, 130723, 130620)
• Cam Lock Screws/Dowels: 8x (Part numbers: 118137, 122971, 141028, 130725, 119253)
• Allen Key: 1x (Part number: 100006)
• Wall Bracket: 1x (Part number: 144342)
• Long Metal Bar: 2x
• Various Brackets and Supports: (Refer to diagrams for specific types and quantities, e.g., 1x bracket, 8x shelf supports 115444, 8x shelf supports 115443)
• Trim Pieces: (e.g., 2x 144351, 144352, 144353; 1x part number not clear)
• Cable Management Clips: (e.g., 1x 133209, 133210, 133212, 133211, 133208, 10093085)
• Wall Mounting Hardware: 1x Wall bracket (103693)

Assembly Steps

1. Step 1: Attach the 6 feet (114947, 115988) to the bottom panel using screws.
2. Step 2: Connect the side panels to the bottom panel using 12x screws (130618). Ensure panels are oriented correctly.
3. Step 3: Slide the back panels into the grooves on the side and bottom panels.
4. Step 4: Insert 4x cam lock housings (e.g., 118137) into the designated holes on the vertical divider panels. Insert 8x cam lock screws (e.g., 130619) into the corresponding holes on the horizontal panels. Connect the vertical dividers to the horizontal panels and turn the cam locks to secure.
5. Step 5: Attach the wall bracket (144342) to the top panel using 1x screw (113287).
6. Step 6: Insert the back panels into the grooves of the assembled structure.
7. Step 7: Attach internal vertical dividers using 2x cam lock housings (e.g., 118137) and 8x cam lock screws (e.g., 130619).
8. Step 8: Insert the back panels into the grooves.
9. Step 9: Carefully place the top panel onto the assembled structure, aligning it with the side and back panels.
10. Step 10: Secure the top panel by turning the cam locks (e.g., 118137) to engage with the cam lock screws (e.g., 130619).
11. Step 11: Attach the front trim pieces (2x, e.g., 144351, 144352, 144353) by sliding them into place and securing them.
12. Step 12: Attach the remaining front trim piece (1x) by sliding it into place and securing it.
13. Step 13: Attach horizontal trim pieces (1x each, e.g., 133203, 144567) to the front of the unit using screws (109049).
14. Step 14: Route any cables through the designated openings in the back panel.
15. Step 15: Attach cable management clips (e.g., 133209) to secure cables. You should hear a 'Click!' when they are properly attached.
16. Step 16: Use the Allen key (100006) and screws to adjust the height of the feet for leveling the unit.
17. Step 17: Adjust the feet using the Allen key and screws until the unit is level.
18. Step 18: Wall Attachment: Attach the wall bracket (103693) to the wall using appropriate screws and plugs (not included). Then, attach the other part of the bracket to the furniture and connect the two parts securely. This is a critical safety step to prevent tip-over.
19. Step 19: Insert shelf supports (8x 115444 and 8x 115443) into the desired holes inside the unit. Place the shelves onto the supports.

Final Check

Ensure all screws are tightened and the unit is stable. Verify that the wall attachment is securely installed.