IKEA BESTÅ Media Unit Assembly Instructions
Safety First: Preventing Tip-Over
⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over. To prevent tip-over, this furniture MUST be used with the wall attachment device(s) provided.
Screws and wall plugs are not included. Use screws and plugs suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instructions carefully.
Parts Included
The following components are included in the package. Note that screws and wall plugs for securing the unit to the wall are not provided, as they must be specific to your wall type.
- Base Panel (1)
- Top Panel (1)
- Side Panels (2)
- Vertical Divider Panels (2)
- Back Panels (2)
- Adjustable Feet (6)
- Cam Lock Dowels (approx. 12)
- Cam Locks (approx. 8)
- Various Screws (e.g., 1x 100006, 12x 118137, 2x 113287, 4x 109049, 16x 116637)
- Wall Attachment Brackets (2x 144342)
- Other Brackets and Connectors (various quantities, e.g., 8x 115444, 8x 115443)
- Drawer/Runner components (various quantities, e.g., 2x 144351, 1x 144352, 1x 144353)
- Cable Management components (various quantities, e.g., 1x 144351, 2x 144352, 1x 144353)
- Assembly Tool (1x Allen key 100006)
Note: Specific part numbers are referenced in the diagrams for precise identification.
Assembly Steps
Step 1: Attach Feet
Place the base panel on a flat surface. Attach the 6 adjustable feet to the underside of the base panel using the provided screws (e.g., 114947, 115988).
Step 2: Assemble Main Frame
Insert cam lock dowels into the designated holes on the base panel. Attach the two side panels to the base panel by aligning the dowels and securing them with cam locks.
Step 3: Insert Back Panels
Slide the back panels into the grooves on the side and base panels.
Step 4: Add Internal Dividers
Insert cam lock dowels into the base and side panels. Attach the two vertical divider panels to the base and side panels, securing them with cam locks.
Step 5: Attach Mounting Brackets to Unit
Attach the wall attachment brackets (e.g., 144342) to the top rear edge of the unit using screws (e.g., 113287, 118137). Ensure they are oriented correctly.
Step 6: Insert Vertical Supports
Insert the vertical support panels into their respective positions within the frame, aligning with pre-drilled holes.
Step 7: Attach Horizontal Panels
Insert cam lock dowels into the vertical panels. Attach the horizontal shelf panels, securing them with cam locks.
Step 8: Insert Shelf Supports
Insert shelf support pins (e.g., 115444, 115443) into the desired height positions on the side and divider panels.
Step 9: Attach Top Panel
Carefully place the top panel onto the assembled unit, aligning it with the side and divider panels.
Step 10: Secure Top Panel
From the underside or inside, insert cam lock dowels and secure the top panel by tightening the cam locks.
Step 11: Install Drawer Runners/Guides
Attach the drawer runners/guides to the inside of the unit panels using the provided screws. Ensure they are level and correctly positioned.
Step 12: Attach Cable Management Guide
Attach the cable management guide to the back of the unit using the provided components.
Step 13: Final Wall Bracket Attachment
Attach any remaining wall mounting hardware to the unit as indicated. This often involves securing brackets to the top or back of the unit.
Step 14: Cable Routing
Route cables through the designated openings and management guides on the unit.
Step 15: Secure Cable Management Covers
Attach any covers or clips to secure the cables neatly. A "click" sound indicates secure attachment.
Step 16: Level the Unit (Initial Adjustment)
Using the provided tool (e.g., Allen key 100006), adjust the 4 feet to bring the unit to a stable, level position.
Step 17: Final Foot Adjustment
Make final adjustments to the remaining 2 feet to ensure the unit is perfectly level and stable on your floor.
Step 18: Secure Unit to Wall
⚠️ IMPORTANT: Position the unit against the wall. Mark the wall through the holes in the wall attachment brackets. Drill holes in the wall and insert appropriate wall plugs. Secure the unit to the wall using suitable screws (not included) through the brackets. Ensure the unit is firmly attached to prevent tipping.
Step 19: Insert Shelves
Place the shelves onto the installed shelf supports at your desired heights.
