BESTÅ TV Bench Assembly Instructions
⚠️ WARNING!
Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.
This section is presented in multiple languages in the original document; the English version is used here as the primary language.
Tools and Parts
Tools Required
- Phillips head screwdriver ➕
- Flathead screwdriver ➖
- Spirit level ?
Diagram shows a person holding a Phillips screwdriver, a flathead screwdriver, and a spirit level.
Parts List
The following components are included:
| Quantity | Part Description / Number |
|---|---|
| 16x | Screw (Part 130618) |
| 8x | Cam lock (Parts 118137, 122971, 141028, 130725, 119253) |
| 8x | Cam lock (Parts 130619, 130722, 141027, 130723, 130620) |
| 4x | Screw (Part 109049) |
| 8x | Screw (Part 113287) |
| 1x | Hex key (Part 100006) |
| 4x | Wall bracket (Part 144342) |
| 4x | Corner bracket (Parts 144343, 144344, 144345, 144346, 144347) |
| 4x | Wall bracket clip (Part 103693) |
| 2x | Long rail/support (Parts 144567, 144568, 144569, 144570, 144571, 10093069) |
| 1x | Short rail/support (Part 133209, 133210, 133212, 133211, 133208, 10093085) |
| 1x | Short rail/support (Part 133203, 133204, 133205, 133207, 133206, 10093227) |
| 6x | Shelf support (Part 115444) |
| 6x | Shelf support (Part 115443) |
Diagram shows all individual parts with their respective quantities and part numbers.
Assembly Steps
Step 1: Attach Feet
Attach 8 feet (Part 114947, 115988) to the underside of the base panel. Ensure they are screwed in securely.
Diagram shows the base panel lying flat and 8 feet being screwed into the pre-drilled holes.
Step 2: Assemble Main Frame
Insert dowels and cam locks into the side panels. Attach the side panels to the base panel. Use 16x screws (Part 130618) to connect the panels.
Diagram shows side panels being attached to the base, with screws being inserted.
Step 3: Attach Bracket to Panel
Attach bracket (Part 144342) to a panel using 2x screws (Part 113287).
Diagram shows a bracket being screwed onto a panel.
Step 4: Attach Another Panel
Attach another panel to the main assembly.
Diagram shows another panel being fitted into place.
Step 5: Secure with Cam Locks
Insert 4x cam locks (Parts 118137, 122971, 141028, 130725, 119253) into the designated holes and turn them clockwise ? to lock the panels together.
Diagram shows cam locks being inserted and turned to secure the structure.
Step 6: Attach Bracket to Panel
Attach bracket (Part 144342) to a panel using 2x screws (Part 113287).
Diagram shows a bracket being screwed onto a panel, similar to Step 3.
Step 7: Insert Internal Dividers
Insert the internal divider panels into the main frame. Ensure they are seated correctly.
Diagram shows internal divider panels being slotted into the unit.
Step 8: Secure with Cam Locks
Insert 4x cam locks (Parts 118137, 122971, 141028, 130725, 119253) and turn them clockwise ? to lock the structure.
Diagram shows cam locks being inserted and turned to secure the structure.
Step 9: Insert Back Panels
Slide the back panels into the grooves on the rear of the unit.
Diagram shows back panels being slid into place.
Step 10: Attach Top Panel
Place the top panel onto the assembled unit. Secure it using the provided connectors and cam locks.
Diagram shows the top panel being placed and secured.
Step 11: Secure with Cam Locks
Insert 4x cam locks (Parts 130619, 130722, 141027, 130723, 130620) and turn them clockwise ? to finalize the main structure.
Diagram shows cam locks being inserted and turned.
Step 12: Attach Back Supports
Attach the back support rails (Parts 144348, 144349, 144350) to the back of the unit using the provided connectors.
Diagram shows back support rails being attached to the rear of the unit.
Step 13: Attach Rail Connectors
Attach the rail connectors to the unit.
Diagram shows rail connectors being attached.
Step 14: Attach Wall Mounting Brackets
Attach the wall mounting brackets (Parts 133203, 133204, 133205, 133207, 133206, 10093227) to the top rear of the unit. Use screws (Part 109049).
Diagram shows wall mounting brackets being screwed onto the top rear edge of the unit.
Attach the other set of wall mounting brackets (Parts 144567, 144568, 144569, 144570, 144571, 10093069) to the top rear of the unit. Use screws (Part 109049).
Diagram shows the second set of wall mounting brackets being screwed onto the top rear edge of the unit.
Step 15: Cable Management
Route cables through the designated openings and clips on the back of the unit.
Diagram shows cables being fed through the back of the unit and secured with clips.
Step 16: Secure Cable Management
Secure the cable management system using the provided clips (Parts 133209, 133210, 133212, 133211, 133208, 10093085).
Diagram shows clips being attached to secure cables, with audible "Click!" indicators.
Step 17: Wall Mounting - Preparation
Position the assembled unit against the wall where it will be installed. Use a spirit level ? to ensure it is straight. Attach the wall mounting hardware (Part 100006) to the unit.
Diagram shows the unit against the wall, with a spirit level being used. It also shows the hex key (Part 100006) being used to attach hardware to the unit.
Step 18: Wall Mounting - Height Adjustment
Adjust the height of the unit using the adjustable feet. Ensure the unit is level.
Diagram shows hands adjusting the feet of the unit to level it.
Step 19: Wall Mounting - Securing to Wall
Mark the wall for drilling according to the measurements provided (e.g., 80 mm from the top edge, 43 mm from the side edges, with specific spacing between brackets). Drill holes and insert appropriate wall plugs (not included). Attach the wall brackets (Part 103693) to the wall using screws (not included).
Diagram shows marking the wall, drilling, inserting wall plugs, and attaching wall brackets. It also shows the unit being hung on the wall brackets with an audible "Click!".
Measurements shown: 80 mm (3 1/8") from top, 43 mm (1 11/16") from sides, 600 mm (23 5/8") spacing, 514 mm (20 1/4") spacing.
Step 20: Final Wall Attachment
Ensure the unit is securely attached to the wall brackets. The diagram shows the unit being pushed onto the wall brackets until it clicks into place.
Diagram shows the unit being pushed onto the wall brackets, with a "Click!" sound effect indicated.
Step 21: Insert Shelves
Insert the shelf supports (Parts 115444, 115443) into the desired holes inside the unit. Place the shelves onto the supports.
Diagram shows shelf supports being inserted and shelves being placed on them.
UPPLEVA Product Line Note
The UPPLEVA product line may not be available in all countries. Please check local IKEA stores for availability.
This information is presented in multiple languages on page 14 of the original document.
Final Checks and Safety
Ensure all screws and fixings are tight. Verify that the unit is securely attached to the wall to prevent tip-over accidents.
Diagrams show a TV on the unit and a warning about tip-over. Another diagram shows the unit securely mounted on the wall.
