FUFUGAGA Cabinet Assembly Instructions

Important Information & Safety Warnings

❓ IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

⚠️ AVOID SCRATCHES! In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

? IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

? ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

❗ IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.

For regular maintenance and cleaning of the product frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools Required

[Person icon] Please prepare the following tools:

• Screwdriver (Phillips head)
• Drill (optional, for wall attachment)

⚠️ When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.

Hardware List:

Assembly Steps

[Icon: Two people assembling furniture] Assembled by 2 adults.

Step 1

Screw eccentric rod (A) and insert wooden dowel (D) into boards 14, 12, 8, 7, and 10 as shown. Fix rail (M) to board 8 and rail (L) to board 10 respectively, using screw (E) as shown.

Diagram shows boards with pre-drilled holes. Eccentric rods (A) are screwed in, and wooden dowels (D) are inserted. Rails (M) and (L) are attached to specific boards using screws (E). Rotation indicators (180°) are shown.

Step 2

Screw eccentric rod (A) into boards 19, 3, and 2 as shown. Insert wooden dowel (D) into boards 2 and 3 as shown. Fix part (N) to board 2 with screw (E) as shown.

Similar to Step 1, showing eccentric rods (A) and dowels (D) being inserted into boards 19, 3, and 2. Part (N) is attached to board 2 with screw (E). Rotation indicators (180°) are shown.

Step 3

Attach board 19 to board 20, add cam lock (C) into board 20 and turn clockwise to tighten. Attach board 19 and 20 to board 14, add cam lock (C) into boards 19, 20 and turn clockwise to tighten. Attach board 18 to board 3, add cam lock (C) into board 18 and turn clockwise to tighten.

Shows boards being joined using cam locks (C). A close-up shows inserting a cam lock and turning it 180° to secure the connection.

Step 4

Attach boards 13 and 14 to board 12, adding cam lock (B) into board 13 and cam lock (C) into board 14 and 19, turning clockwise to tighten. Attach board 7 to boards 13 and 14, adding cam lock (B) into board 13 and cam lock (C) into board 14 and 20, turning clockwise to tighten.

Illustrates connecting curved and straight boards using cam locks (B) and (C). A close-up shows the cam lock mechanism being tightened.

Step 5

Attach board 12 to board 7, adding cam lock (B) into board 12 and turning clockwise to tighten. Attach board 10 to board 3, adding cam lock (B) into board 10 and turning clockwise to tighten.

Shows attaching vertical panels to horizontal ones using cam locks (B). A close-up shows the cam lock tightening.

Step 6

Attach boards 15 and 16 to board 10, adding cam lock (C) into boards 15, 16 and turning clockwise to tighten.

Shows attaching shelf panels (15, 16) to a main support board (10) using cam locks (C).

Step 7

Attach board 7 to boards 15, 3, and 18, adding cam lock (C) into boards 15, 3, 18 and turning clockwise to tighten.

Shows attaching a large side panel (7) to multiple horizontal and vertical panels using cam locks (C).

Step 8

Attach board 8 to boards 16, 3, and 18, adding cam lock (C) into boards 16, 3, 18 and turning clockwise to tighten.

Shows attaching another large side panel (8) to the structure using cam locks (C).

Step 9

Insert back board 23 along the available grooves as shown.

Shows two large back panels (23) being slid into grooves on the rear of the partially assembled cabinet structure.

Step 10

Cover board 2 to the top, adding cam lock (B) into boards 12, 7, 10, 8 and turning clockwise to tighten.

Shows the top panel (2) being attached to the main structure using cam locks (B).

Step 11

Screw eccentric rod (A) and insert wooden dowel (D) into boards 1, 4, 6, 11, and 5 as shown.

Shows eccentric rods (A) and dowels (D) being inserted into several flat panels (1, 4, 6, 11, 5).

Step 12

Attach board 13 to board 11, adding cam lock (B) into board 13 and turning clockwise to tighten. Attach board 5 to boards 13 and 11, adding cam lock (B) into board 13 and turning clockwise to tighten.

Shows attaching curved shelf panels (13) and side panels (5) to a base panel (11) using cam locks (B).

Step 13

Attach board 5 to board 11, adding cam lock (B) into board 11 and turning clockwise to tighten. Attach board 17 to board 5, adding cam lock (C) into board 17 and turning clockwise to tighten.

Shows attaching a side panel (5) to a base (11) with cam locks (B), and then attaching a support panel (17) to the side panel (5) with cam locks (C).

Step 14

Attach board 4 to board 5, adding cam lock (C) into board 4 and turning clockwise to tighten. Attach board 9 to board 4, adding cam lock (B) into board 9 and turning clockwise to tighten.

Shows attaching a vertical panel (4) to a side panel (5) with cam locks (C), and then attaching another vertical panel (9) to panel (4) with cam locks (B).

Step 15

Insert back board 22 along the available grooves as shown.

Shows a back panel (22) being slid into grooves on the rear of a section of the cabinet.

Step 16

Attach board 6 to boards 4 and 17, adding cam lock (C) into board 4 and turning clockwise to tighten.

Shows attaching a panel (6) to panels (4) and (17) using cam locks (C).

Step 17

Insert back board 21 along the available grooves as shown.

Shows two back panels (21) being slid into grooves on the rear of the cabinet structure.

Step 18

Cover board 1 to the top, adding cam lock (B) into boards 11, 5, 6, 9 and turning clockwise to tighten.

Shows the top panel (1) being attached to the main structure using cam locks (B).

Step 19

Connect the two assembled components, adding cam lock (B) and turning clockwise to tighten.

Shows two large sub-assemblies being joined together using cam locks (B). A close-up shows the cam lock mechanism being tightened.

Step 20

Insert buckle (Q) into back slots and fix to tighten. Add cam lock (B) into board 11, and cam lock (C) into board 17, turning clockwise to tighten.

Shows buckles (Q) being inserted into rear slots. Cam locks (B) are added to board 11, and cam locks (C) to board 17.

Step 21

Screw eccentric rod (A) into board 27 as shown. Fix knob (H) to board 27 as shown. (Repeat x2)

Shows eccentric rods (A) being screwed into a panel (27), and knobs (H) being attached to the same panel. This step is for two identical drawer fronts/sides.

Step 22

Fix boards 28 and 29 to board 30 with screw (G) as shown. Insert bottom board 31 along grooves as shown. (Repeat x2)

Shows the sides (28, 29) of two drawers being attached to a back panel (30) with screws (G). The bottom panel (31) is then slid into grooves.

Step 23

Attach board 27 to boards 28 and 29, adding cam lock (C) and turning clockwise to tighten. Fix runner (L) and (M) to boards 28 and 29 with screw (E) as shown. (Repeat x2)

Shows drawer front panels (27) being attached to drawer boxes (28, 29, 30, 31) using cam locks (C). Drawer runners (L, M) are attached to the drawer sides using screws (E).

Step 24

Fix hinge (K) to boards 24, 25, and 26 with screw (F) as shown. Fix handle (J) to boards 24, 25, and 26 as shown. Fix part (N) to board 26 with screw (E) as shown.

Shows hinges (K) being attached to door panels (24, 25, 26) with screws (F). Handles (J) are attached to the doors. Part (N) is attached to panel 26 with screw (E).

Step 25

Assemble doors 24, 25, and 26 to boards 5, 6, and 7 by fixing hinges with screw (F) as shown.

Shows the assembled doors being attached to the main cabinet structure via their hinges and screws (F).

Step 26

Align rails, insert drawers in.

Shows the cabinet with drawers (27) being slid into place along the installed rails.

Step 27

If doors are still not aligned, please watch the video for hinge adjustment.

Video Link: https://youtu.be/n0Lb36S0ODM

Illustrates hinge adjustment steps (I, II, III) for aligning doors.

Step 28

Install anti-tipping device as shown.

Shows the anti-tipping strap being attached to the top of the cabinet and then secured to a wall. Steps detail drilling into the wall and securing the strap.

Step 29

Use sticker (R) to cover all cam lock holes.

Shows stickers (R) being applied over visible cam lock holes on the assembled cabinet.

Warranty Information

Warranty Claims

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call us. Leave your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and returned within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Does not include damage during installation, but includes damage during transportation.

Scope of Responsibility

• No responsibility will be borne for misuse, user damage, or loss of parts during installation.
• Damage and scratches after use are not covered by the warranty.

Warranty Coverage (US)

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

Changed Your Mind?

If you have simply changed your mind, follow the retailer's instructions for returns.

Defective Items

If your item is defective in any way, please call us first for assistance.

Damaged Items

If you receive an order with obvious shipping damage, refuse the delivery. If damage is found after acceptance, follow the retailer's specific instructions. Always save all packaging material and paperwork. Disposing of packaging or attempting to return without contacting the fulfillment center may jeopardize your claim.

After-Sales Contact

Email: feedbackstation@163.com

Phone: (303)800-6387