Cabinet
Version: 12/01/2023
Assembled by 2 Adults ?
Important Information ❗
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Assembly Tips
Avoid Scratches ⚠️: In order to avoid scratching this furniture, it should be assembled on a soft layer, such as a rug.
Improve Efficiency ?: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Topple Warning ⚠️
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important Note: It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the lifespan of the product.
Maintenance and Cleaning: For the frame, use a rag dipped in neutral detergent to wipe it, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools Required ???
Parts List
When installing, please carefully confirm whether each screw corresponds to the manual; accessories with similar shapes can be distinguished by size.
M6.5 x 35 mm
Ø15 x 9.5 mm
Ø8 x 30 mm
Ø35 mm
Ø35 mm
M3.5 x 14 mm
Ø26 x 11 mm
1.5 m
19 x 14 x 8 mm
M3 x 14 mm
Exploded View
The following numbered parts are used in assembly:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9 (Back Board)
- 10 (Back Board)
- 11
- 12
- 13 (Door Panel)
- 14 (Door Panel)
- 15 (Door Panel)
WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:
- ALWAYS install tipover restraint provided.
- NEVER put a TV on this product.
- NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
- NEVER open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove!
Assembly Steps
Step 1
Screw eccentric rod(A) x 2 into board 5 as shown.
Diagram shows board 5 with two eccentric rods (A) being screwed into pre-drilled holes.
Step 2
Attach board 11 to board 5 using wooden dowel(C) x 2. Add cam lock(B) x 2 into board 11 and turn clockwise to tighten as shown.
Diagram shows board 11 being attached to board 5 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection.
Step 3
Screw eccentric rod(A) x 2 into board 5 as shown.
Diagram shows board 5 with two eccentric rods (A) being screwed into pre-drilled holes.
Step 4
Attach board 12 to board 5 using wooden dowel(C) x 2. Add cam lock(B) x 2 into board 12 and turn clockwise to tighten as shown.
Diagram shows board 12 being attached to board 5 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection.
Step 5
Screw eccentric rod(A) x 4 into board 1 as shown.
Diagram shows board 1 with four eccentric rods (A) being screwed into pre-drilled holes.
Step 6
Attach board 6 to board 1 using wooden dowel(C) x 2. Add cam lock(B) x 3 into board 6 and turn clockwise to tighten as shown.
Diagram shows board 6 being attached to board 1 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection.
Step 7
Screw eccentric rod(A) x 3 into board 1 as shown.
Diagram shows board 1 with three eccentric rods (A) being screwed into pre-drilled holes.
Step 8
Attach board 8 to board 1 using wooden dowel(C) x 2. Add cam lock(B) x 3 into board 8 and turn clockwise to tighten as shown.
Diagram shows board 8 being attached to board 1 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection.
Step 9
Connect board 1 to board 5 using wooden dowel(C) x 1. Add cam lock(B) x 1 into board 5 and turn clockwise to tighten as shown.
Diagram shows board 1 being connected to board 5 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection. The assembly now shows boards 1, 5, 6, 8, 11, and 12 connected.
Step 10
Screw eccentric rod(A) x 4 into board 2 as shown.
Diagram shows board 2 with four eccentric rods (A) being screwed into pre-drilled holes.
Step 11
Attach board 7 to board 2 using wooden dowel(C) x 2. Add cam lock(B) x 3 into board 7 and turn clockwise to tighten as shown.
Diagram shows board 7 being attached to board 2 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection.
Step 12
Connect board 2 to board 5 using wooden dowel(C) x 1. Add cam lock(B) x 1 into board 5 and turn clockwise to tighten as shown.
Diagram shows board 2 being connected to board 5 using dowels and cam locks. A close-up shows the 180° rotation of the cam lock to secure the connection. The assembly now shows boards 1, 2, 5, 6, 7, 8, 11, and 12 connected.
Step 13
Insert back board 9 along available grooves as shown.
Diagram shows the partially assembled unit with back board 9 being slid into the grooves from the rear.
Step 14
Screw eccentric rod(A) x 7 into board 3 as shown.
Diagram shows board 3 with seven eccentric rods (A) being screwed into pre-drilled holes.
Step 15
Connect board 3 to boards 2, 7, 6, 1, 8, and 11 using wooden dowel(C) x 6. Add cam lock(B) x 3 into boards 6, 7, 8 and turn clockwise to tighten as shown.
Diagram shows board 3 being attached to multiple other boards using dowels and cam locks. A close-up shows the 180° rotation of the cam lock.
Step 16
Fix back board 9 to the unit with screw(K) x 4 as shown. Insert back board 10 along available grooves as shown.
Diagram shows back board 9 being secured with screws (K). Back board 10 is then shown being inserted into grooves.
Step 17
Screw eccentric rod(A) x 7 into board 4 as shown.
Diagram shows board 4 with seven eccentric rods (A) being screwed into pre-drilled holes.
Step 18
Connect board 4 to boards 2, 7, 6, 1, 8, and 12 using wooden dowel(C) x 6. Add cam lock(B) x 3 into boards 6, 7, 8 and turn clockwise to tighten as shown.
Diagram shows board 4 being attached to multiple other boards using dowels and cam locks. A close-up shows the 180° rotation of the cam lock.
Step 19
Add cam lock(B) x 8 into boards 1, 2, 11, and 12 and turn clockwise to tighten as shown.
Diagram shows cam locks (B) being inserted and tightened into various boards (1, 2, 11, 12) to secure the main frame of the cabinet.
Step 20: Wall Mounting
Fix the unit to the wall using part(L) x 6 sets.
Diagram shows the cabinet mounted on a wall. Steps illustrate drilling into the wall, inserting wall anchors, and securing the cabinet using part L.
Door Hinge Explanation
Pay attention to the difference between the middle parts of the two types of door hinges.
- The flat door hinges(D) are used on the outermost door plates.
- The curved door hinges(E) are used on the door panel in the middle of the cabinet.
Diagrams show two types of hinges, labeled D (flat) and E (curved), with arrows indicating their orientation.
Step 22: Attach Hinges to Door 13
Fix hinge(D) x 2 to board 13 with screw(F) x 4 as shown.
Diagram shows hinge D being attached to door panel 13 using screws F.
Step 23: Assemble Door 13 to Cabinet
Assemble door 13 to board 3 by fixing hinge with screw(F) x 8 as shown.
Diagram shows door panel 13 being attached to the cabinet frame (board 3) using hinges and screws F.
Step 24: Attach Hinges to Door 14
Fix hinge(E) x 2 to board 14 with screw(F) x 4 as shown.
Diagram shows hinge E being attached to door panel 14 using screws F.
Step 25: Assemble Door 14 to Cabinet
Assemble door 14 to board 5 by fixing hinge with screw(F) x 8 as shown.
Diagram shows door panel 14 being attached to the cabinet frame (board 5) using hinges and screws F.
Step 26: Attach Hinges to Door 15
Fix hinge(D) x 2 to board 15 with screw(F) x 4 as shown.
Diagram shows hinge D being attached to door panel 15 using screws F.
Step 27: Assemble Door 15 to Cabinet
Assemble door 15 to board 4 by fixing hinge with screw(F) x 8 as shown.
Diagram shows door panel 15 being attached to the cabinet frame (board 4) using hinges and screws F.
Door Alignment
If doors are still not aligned correctly, please watch the video.
Diagrams illustrate hinge adjustment steps for alignment.
Step 29: Lighting and Power Connection
Connect the light strip with power supply(H) as shown.
Instructions:
- Place the wire box(G) into the corresponding position at first.
- Tear off the sticker of part(J), stick it to a proper place of board 1. Press to open the clamp, put in the power cord, and press to close.
Diagram shows the light strip being connected to the power supply and wire box. It also illustrates attaching part J to board 1 for cable management.
Electrical Connections
Connect to Wall Switch
1) Plugs are provided with this product. Recommend to use the plug directly.
2) If you need to link to a wall switch, you can choose to cut off the plug and link the wire. Note: When the plug is cut off, the product is not covered by the warranty. It is recommended that you contact an electrician to install it, or operate under the guidance of a professional.
Specifications:
- Input Voltage: 110V AC
- Output Voltage: 12V DC
- Type: Touch Switch
- Color Temperature: 3000K - 4000K - 6500K
1. ON/OFF/Switch-color Function
- Short Press to turn on/off and change the color temperature.
- Or Press the switch button and hold for 2-3 seconds to activate the dimmer function after turn on. After the lamp dimmer function is activated, the long press light switch brightness changes from dark to light, and the long press light brightness changes from light to dark.
2. Defogger button ♨️
- First short press: anti-fog function works.
- Second short press: anti-fog function stops.
- The two operations cycle in turn.
WARRANTY
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
- Before making a claim, please call us. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. We will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
- The product must be used in accordance with the instructions provided. For health reasons.
- For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Does not include damage during installation, but includes damage during transportation.
Scope of responsibility
- Shall not bear any responsibility for misuse or user damage and / or loss of parts during the installation of furniture.
- After using, the damage and scratches of the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The Us and Covers The Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
RETURNS
CHANGED YOUR MIND AND NEED TO RETURN YOU ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e. it doesn't work but you can't identify why, in the first instance, please call us.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
AFTER-SALES CONTACT
Email: feedbackstation@163.com
Phone: (303)800-6387
