INSTALLATION Product Manual

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Avoid Scratches

To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

Improve Efficiency

Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Topple Warning

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

Important Maintenance Notes

It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product. For regular maintenance and cleaning of the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools Required

Please prepare the following tools:

• Screwdriver (Phillips head)
• Hammer
• Electric Screwdriver (use with caution)
• Allen Wrench (if included)

Parts List

When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

• A x 92 (CRA0635A)
• B x 116 (CRB1595A)
• C x 112 (CRF0830A)
• D x 12 (CRD0430A)
• E x 12 (CRD0425A)
• F x 8 (DGA861A)
• G x 16 (DGA861B)
• H x 182 (CRD3514A)
• J x 6 (CRD3514A)
• K x 4 (K2, K1)
• L x 800 mm (#4512 14")
• M x 24 (DGA861A)
• N x 24 (CRD0316A)
• P x 54 (CRE0312A)
• Q x 10 (CRD3512A)
• R x 4
• S x 1
• T x 2
• U x 24 (CRA0660A)
• V x 12 (9.5 x 12 mm)
• W x 1 (783 mm)

Assembly Overview

Diagram shows an exploded view of the furniture components with numbered parts. A warning section highlights the risk of furniture tipover and provides safety instructions: ALWAYS install tipover restraint provided. NEVER put a TV on this product. NEVER allow children to stand, climb or hang on drawers, doors, or shelves. NEVER open more than one drawer at a time. Place heaviest items in the lowest drawers. This is a permanent label. Do not remove!

The diagram also indicates that the furniture is "ASSEMBLED BY 2 ADULTS".

Step 1: Slide Separation

Instructions for separating drawer slides. The slides consist of a Mount, Cage, Lever, and Runner. The process involves extending the slide, pushing the lever up, and then removing the runner.

Diagrams illustrate these three steps: 1. Extend Slide, 2. Push Lever UP, 3. Remove Runner.

Step 2: Assembling Base Panel

Parts used: A x 4, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 9 at first. Fix part (Q) to board 9 with screw (H) as shown.

Diagram shows board 9 with eccentric rods (A) being screwed in at designated points. Part (Q) is shown being attached to board 9 with screw (H).

Step 3: Connecting Side Panels

Parts used: B x 4, C x 4.

Action: Connect board 1 and 13 to board 9 using wooden dowel (C). Add cam lock (B) into board 1 and 13 and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 1 and 13 being attached to board 9 using dowels (C) and cam locks (B). A close-up shows the cam lock mechanism.

Step 4: Connecting Another Side Panel

Parts used: A x 4, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 11 at first. Fix part (Q) to board 11 with screw (H) as shown.

Diagram shows board 11 with eccentric rods (A) and part (Q) attached with screw (H).

Step 5: Connecting Panels

Parts used: B x 4, C x 4.

Action: Connect board 11 to board 1 and 13 using wooden dowel (C). Add cam lock (B) into board 1 and 13 and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 1 and 13 being attached to board 11 using dowels (C) and cam locks (B).

Step 6: Attaching Base Panels

Parts used: A x 8.

Action: Screw eccentric rod (A) into board 3 at first.

Diagram shows board 3 with eccentric rods (A) inserted (x2).

Step 7: Attaching Support Beams

Parts used: B x 8, C x 8.

Action: Attach board 17 to board 3 using wooden dowel (C). Add cam lock (B) into board 17 and turn clockwise to tighten as shown.

Diagram shows boards 17 being attached to board 3 using dowels (C) and cam locks (B) (x2).

Step 8: Assembling Another Section

Parts used: A x 6, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 12 at first. Fix part (Q) to board 12 with screw (H) as shown.

Diagram shows board 12 with eccentric rods (A) and part (Q) attached with screw (H).

Step 9: Connecting Panels

Parts used: B x 6, C x 6.

Action: Attach board 17, 3, 15 and 16 to board 12 using wooden dowel (C). Add cam lock (B) into board 17, 3, 15, 16 and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 17, 3, 15, and 16 being attached to board 12 using dowels (C) and cam locks (B).

Step 10: Assembling Another Section

Parts used: A x 6, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 10 at first. Fix part (Q) to board 10 with screw (H) as shown.

Diagram shows board 10 with eccentric rods (A) and part (Q) attached with screw (H).

Step 11: Connecting Panels

Parts used: B x 6, C x 6.

Action: Attach board 10 to board 17, 3, 15 and 16 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows boards 17, 3, 15, and 16 being attached to board 10 using dowels (C) and cam locks (B).

Step 12: Connecting Assembled Components

Parts used: C x 4, E x 6.

Action: Connect the two assembled components using wooden dowel (C), and fix board 15 and 16 to board 13 with screw (E) as shown. Ensure holes are facing up.

Diagram shows two previously assembled sections being joined, with boards 15 and 16 attached to board 13.

Step 13: Assembling Another Section

Parts used: A x 8, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 9 and 10 at first. Fix part (Q) to board 9 with screw (H) as shown.

Diagram shows boards 9 and 10 with eccentric rods (A) and part (Q) attached with screw (H).

Step 14: Assembling Base Panel

Parts used: A x 4.

Action: Screw eccentric rod (A) into board 4 at first.

Diagram shows board 4 with eccentric rods (A) inserted.

Step 15: Attaching Support Beams

Parts used: B x 4, C x 4.

Action: Attach board 18 to board 4 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 18 being attached to board 4 using dowels (C) and cam locks (B).

Step 16: Connecting Panels

Parts used: B x 8, C x 6.

Action: Attach board 4, 14 and 2 to board 10 and 9 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 4, 14, and 2 being attached to boards 10 and 9.

Step 17: Assembling Another Section

Parts used: A x 6, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 7 at first. Fix part (Q) to board 7 with screw (H) as shown.

Diagram shows board 7 with eccentric rods (A) and part (Q) attached with screw (H).

Step 18: Connecting Panels

Parts used: B x 4, C x 4.

Action: Attach board 1 and 13 to board 7 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 1 and 13 being attached to board 7.

Step 19: Assembling Another Section

Parts used: A x 4, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 5 at first. Fix part (Q) to board 5 with screw (H) as shown.

Diagram shows board 5 with eccentric rods (A) and part (Q) attached with screw (H).

Step 20: Connecting Panels

Parts used: B x 4, C x 4.

Action: Attach board 5 to board 1 and 13 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows board 5 being attached to boards 1 and 13.

Step 21: Assembling Another Section

Parts used: A x 6, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 8 at first. Fix part (Q) to board 8 with screw (H) as shown.

Diagram shows board 8 with eccentric rods (A) and part (Q) attached with screw (H).

Step 22: Connecting Panels

Parts used: B x 6, C x 6.

Action: Attach board 3, 17, 15 and 16 to board 8 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows boards 3, 17, 15, and 16 being attached to board 8.

Step 23: Assembling Another Section

Parts used: A x 6, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 6 at first. Fix part (Q) to board 6 with screw (H) as shown.

Diagram shows board 6 with eccentric rods (A) and part (Q) attached with screw (H).

Step 24: Connecting Panels

Parts used: B x 6, C x 6.

Action: Attach board 6 to board 3, 17, 15 and 16 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown. Ensure holes are facing up.

Diagram shows board 6 being attached to boards 3, 17, 15, and 16.

Step 25: Connecting Assembled Components

Parts used: C x 4, E x 6.

Action: Connect the two assembled components using wooden dowel (C), and fix board 15 and 16 to board 13 with screw (E) as shown. Ensure holes are facing up.

Diagram shows two previously assembled sections being joined, with boards 15 and 16 attached to board 13.

Step 26: Assembling Another Section

Parts used: A x 8, H x 2, Q x 1.

Action: Screw eccentric rod (A) into board 7 and 8 at first. Fix part (Q) to board 7 with screw (H) as shown.

Diagram shows boards 7 and 8 with eccentric rods (A) and part (Q) attached with screw (H).

Step 27: Connecting Panels

Parts used: B x 8, C x 6.

Action: Attach the component (assembled in step 15) to board 7 and 8 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows a large assembled unit being attached to boards 7 and 8.

Step 28: Fixing Back Boards

Parts used: P x 3.

Action: Fix back board 38 and 39 to board 4 with screw (P) as shown.

Diagram shows the main structure with back boards 38 and 39 being attached to board 4.

Step 29: Connecting Back Boards

Parts used: W x 1.

Action: Connect back board 37 and 38 to plank (W) at first.

Diagram shows back boards 37 and 38 being attached to a plank (W).

Step 30: Securing Back Panels

Parts used: M x 24, N x 24, P x 51.

Action: Fix back board 32, 33, 34, 35 and 36 to the cabinet with screw (P) at first. Use iron sheet (M) to fix back board 32, 33, 34, 35, 36, 37, 38 and 39 with screw (N) as shown.

Diagram shows the entire back of the cabinet being secured with multiple screws (P and N) and iron sheets (M).

Step 31: Attaching Drawer Rails

Parts used: A x 4, K x 4 (K2), L x 8.

Action: Fix rail (K2) to board 22 and 23 with screw (L) as shown. Screw eccentric rod (A) into board 22 and 23 at first.

Diagram shows drawer rails (K2) being attached to boards 22 and 23 with screws (L), and eccentric rods (A) being inserted.

Step 32: Assembling Another Section

Parts used: A x 4.

Action: Screw eccentric rod (A) into board 20 and 21 at first.

Diagram shows boards 20 and 21 with eccentric rods (A) inserted.

Step 33: Connecting Panels

Parts used: B x 2, C x 2.

Action: Attach board 20 to board 22 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 20 being attached to board 22.

Step 34: Connecting Panels

Parts used: B x 2, C x 2.

Action: Attach board 24 to board 22 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 24 being attached to board 22.

Step 35: Connecting Panels

Parts used: B x 2, C x 2.

Action: Attach board 21 to board 23 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 21 being attached to board 23.

Step 36: Connecting Panels

Parts used: B x 2, C x 2.

Action: Attach board 23 to board 24 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 23 being attached to board 24.

Step 37: Assembling Another Section

Parts used: A x 6.

Action: Screw eccentric rod (A) into board 19 at first.

Diagram shows board 19 with eccentric rods (A) inserted.

Step 38: Connecting Panels

Parts used: B x 6, C x 6.

Action: Attach board 19 to board 20, 21, 22 and 23 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows board 19 being attached to boards 20, 21, 22, and 23.

Step 39: Attaching Drawer Runners

Parts used: K x 4 (K1), L x 8.

Action: Fix runner (K1) to board 27 and 28 with screw (L) as shown.

Diagram shows drawer runners (K1) being attached to boards 27 and 28.

Step 40: Connecting Drawer Sides

Parts used: D x 8.

Action: Fix board 27 and 28 to board 29 with screw (D) as shown.

Diagram shows boards 27 and 28 being attached to board 29.

Step 41: Inserting Bottom Board

Action: Insert bottom board 31 along grooves as shown.

Diagram shows bottom board 31 being slid into grooves of a drawer assembly.

Step 42: Securing Drawer Front

Parts used: D x 4.

Action: Fix board 30 to board 29 with screw (D) as shown.

Diagram shows board 30 being attached to board 29.

Step 43: Assembling Drawer Sides

Parts used: A x 10.

Action: Screw eccentric rod (A) into board 25 and 26 at first.

Diagram shows boards 25 and 26 with eccentric rods (A) inserted.

Step 44: Assembling Drawer

Parts used: B x 10, C x 2.

Action: Insert wooden dowel (C) into board 30 at first. Attach board 25/26 to board 27, 30 and 28, add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows drawer components being assembled.

Step 45: Inserting Drawers

Action: Align rails, insert drawers in.

Diagram shows drawers being inserted into the main cabinet structure.

Step 46: Placing Main Unit

Action: Place the part into.

Diagram shows a smaller unit (likely the top or a drawer unit) being placed onto the main cabinet structure.

Step 47: Installing Clothing Rods

Parts used: R x 4, S x 1.

Action: Place clothing rod (R) and (S) as shown.

Diagram shows clothing rods (R) and (S) being installed in the wardrobe sections.

Step 48: Assembling Drawer Sides

Parts used: U x 12, V x 12.

Action: Add nut (V) into board 40 and 41 at first. Screw eccentric rod (U) into board 40 and 41.

Diagram shows nuts (V) and eccentric rods (U) being inserted into boards 40 and 41.

Step 49: Connecting Drawer Panels

Parts used: B x 12, C x 12.

Action: Connect board 40 and 41 to board 44/46/48 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows boards 40 and 41 being attached to other panels.

Step 50: Door Hinge Types

Pay attention to the difference between the middle parts of the two types of door hinges.

The full coverage door hinges (F) are used on the outermost door plates. And the small curved door hinges (G) are used on the door panel in the middle of the cabinet.

Diagrams show hinge types F and G.

Step 51: Attaching Hinges (Type F)

Parts used: F x 4, H x 11, J x 1.

Action: Fix hinge (F) to board 40 and 41 with screw (H) as shown. Fix handle (J) with screw (H).

Diagram shows hinges (F) and handles (J) being attached to boards 40 and 41.

Step 52: Assembling Doors

Parts used: H x 16.

Action: Assemble this door to board 5 and 6 by fixing hinge (F) with screw (H) as shown.

Diagram shows a door assembly being attached to the main cabinet structure.

Step 53: Attaching Hinges (Type G)

Parts used: G x 8, H x 22, J x 2.

Action: Fix hinge (G) to board 40 and 41 with screw (H) as shown. Fix handle (J) with screw (H).

Diagram shows hinges (G) and handles (J) being attached to boards 40 and 41.

Step 54: Assembling Doors

Parts used: H x 32.

Action: Assemble these two doors to board 7, 8 and 9, 10 by fixing hinge (G) with screw (H) as shown.

Diagram shows doors being attached to the main cabinet structure.

Step 55: Assembling Drawer Sides

Parts used: U x 12, V x 12.

Action: Add nut (V) into board 42 and 43 at first.

Diagram shows nuts (V) and eccentric rods (U) being inserted into boards 42 and 43.

Step 56: Connecting Drawer Panels

Parts used: B x 12, C x 12.

Action: Connect board 42 and 43 to board 45/47/49 using wooden dowel (C). Add cam lock (B) into and turn clockwise to tighten as shown.

Diagram shows boards 42 and 43 being attached to other panels.

Step 57: Attaching Hinges (Type F)

Parts used: F x 4, H x 11, J x 1.

Action: Fix hinge (F) to board 42 and 43 with screw (H) as shown. Fix handle (J) with screw (H).

Diagram shows hinges (F) and handles (J) being attached to boards 42 and 43.

Step 58: Assembling Doors

Parts used: H x 16.

Action: Assemble this door to board 11 and 12 by fixing hinge (F) with screw (H) as shown.

Diagram shows a door assembly being attached to the main cabinet structure.

Step 59: Attaching Hinges (Type G)

Parts used: G x 8, H x 22, J x 2.

Action: Fix hinge (G) to board 42 and 43 with screw (H) as shown. Fix handle (J) with screw (H).

Diagram shows hinges (G) and handles (J) being attached to boards 42 and 43.

Step 60: Assembling Doors

Parts used: H x 32.

Action: Assemble these two doors to board 7, 8 and 9, 10 by fixing hinge (G) with screw (H) as shown.

Diagram shows doors being attached to the main cabinet structure.

Step 61: Install Anti-Tipping Device

Parts used: T x 2.

Action: Install anti-tipping device as shown.

Diagram shows the installation of an anti-tipping strap.

Step 62: Hinge Adjustment

If doors are still not aligned correctly, please watch the video: https://youtu.be/n0Lb36S0ODM

Diagrams illustrate hinge adjustment steps (I, II, III).

Warranty

Warranty Claims

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call us. Provide your purchase order number and details of the problem for a replacement part. We will respond within 48 hours. If out of stock, we will reply with a shipping date.
• The product must be used in accordance with the instructions provided.
• For returns, the furniture must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is included.

Scope of Responsibility

• No responsibility will be borne for misuse or user damage and/or loss of parts during installation.
• Damage and scratches after use are not covered by the warranty.

Warranty Coverage Areas (USA)

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns

Changed Your Mind?

If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

Defective Items

If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call us first.

Damaged Items

If you receive an order with obvious shipping damage from the retailer, refuse the delivery. If delivery has been accepted and shipping damage is found, follow the specific instructions advised by the retailer.

In all circumstances, please save all packaging material and paperwork for the order. Disposing of packaging material or attempting to return merchandise without contacting the fulfiller may jeopardize your chances of making a claim and you may not receive credit for the return.

After-Sales Contact

• Email: feedbackstation@163.com
• Phone: (303)800-6387