Progress Lighting
P400345 / P400349
3-LT CHANDELIER/CONV
Package Contents
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Glass shade | 3 |
| C | Socket ring | 3 |
| D | Stem | 1 |
| E | Seat ring | 1 |
| F | Chain loop | 1 |
| G | Canopy | 1 |
| H | Lock washer | 1 |
| J | Hex nut | 1 |
The document indicates two assembly options: Ceiling Assembly or Hanging Assembly.
Hardware Contents (not actual size)
| Identifier | DESCRIPTION | QUANTITY |
|---|---|---|
| AA | Screw (#8-32) | 2 |
| BB | Wire Nut | 3 |
| CC | Round Mounting Plate | 1 |
| DD | Hex Nut (#8-32) | 2 |
| EE | Cylinder Nut (#8-32) | 2 |
| FF | Chain (48") | 1 |
| GG | Chain loop (1/8IP) | 1 |
| HH | Quick link | 1 |
Contact Information: For questions regarding product information, assembly, or missing parts, please call 800-447-0573 (Monday-Friday, 8am-8pm Eastern) or email customerservice@progresslighting.com.
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Use minimum 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Preparation
- Before beginning installation, ensure all parts are included by checking the contents diagrams on page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
Step 1: Mounting Plate Preparation
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust the screw length according to the fixture canopy depth.
Visual Description: Diagram shows the round mounting plate (CC) with screws (AA) and hex nuts (DD) attached. Arrows indicate adjusting the position of the hex nuts (DD) on the screws (AA) to set the desired length.
Step 2: Attaching Assembly to Outlet Box
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely. Lift up the fixture and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until approximately 3/16" of threads are showing. This should be enough to mount the fixture as instructed in ceiling step 7 & hanging step 8. Next, take the fixture down and tighten the hex nuts (DD) up against the mounting plate (CC). This ensures the correct thread length for mounting the fixture.
Visual Description: Diagram shows the mounting plate assembly attached to the ceiling. Another diagram shows the fixture canopy being lifted, with screws (AA) passing through its holes and threading into the mounting plate (CC). An inset shows an "INCORRECT" state with too much thread showing and a "CORRECT" state with approximately 3/16" [5mm] of thread showing. Arrows indicate screwing the hex nuts (DD) up against the mounting plate (CC) to lock the screw length.
Step 3: Adjusting Fixture Arms
Equally adjust the arms by carefully turning them out from the center.
Visual Description: Diagram shows the fixture body with arms, and arrows indicating rotation to spread the arms outwards from the center.
Step 4: Connecting Stem to Fixture
Slip the fixture (A) wires through stem (D) and seat ring (E). Thread stem (D) into fixture (A). Attach the seat ring (E) into the stem (D).
Visual Description: Diagram shows fixture wires passing through stem (D) and seat ring (E). Stem (D) is shown being threaded into the base of fixture (A). Seat ring (E) is then attached to the stem (D).
Step 5: Attaching Canopy and Securing Stem (Ceiling Mount)
Slip the fixture (A) wires through canopy (G), lock washer (H), and hex nut (J). Place canopy (G) and lock washer (H) down over the nipple of stem (D) and secure in place with hex nut (J).
Visual Description: Diagram shows fixture wires passing through canopy (G), lock washer (H), and hex nut (J). Canopy (G) and lock washer (H) are shown being placed over the stem (D) and secured with hex nut (J).
Step 6: Wiring Connections (Ceiling Mount)
Strip 3/8" of insulation from the electrical wire ends. Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
Visual Description: Diagram shows wire stripping. It illustrates connecting wires using wire nuts (BB), specifically showing a "Ribbed" wire connecting to a "WHITE" supply wire and a "Smooth" wire connecting to a "BLACK" supply wire. A separate connection shows the ground wire being connected.
Step 7: Securing Canopy to Mounting Screws (Ceiling Mount)
Pass the screws (AA) through the two holes in the canopy (G). Secure the fixture to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
Visual Description: Diagram shows screws (AA) passing through the canopy (G) and being secured by cylinder nuts (EE).
Step 8: Attaching Glass Shades and Lamps (Ceiling Mount)
Attach the glass shade (B) to the fixture (A) using the socket ring (C) to secure it tightly. Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base, SBCFL or SBLED.
Visual Description: Diagram shows glass shade (B) being attached to fixture (A) using socket ring (C). It also shows a lamp being threaded into a socket.
Hanging Assembly Instructions
Step 5: Attaching Chain Loop and Canopy (Hanging Mount)
Slip the fixture (A) wires through chain loop (F). Thread the chain loop (F) into stem (D). Slide the canopy (G) and lock washer (H) down over the nipple of chain loop (GG) and secure in place with hex nut (J).
Visual Description: Diagram shows fixture wires passing through chain loop (F) and threaded into stem (D). Canopy (G) and lock washer (H) are shown sliding down over the chain loop (GG) nipple and secured with hex nut (J).
Step 6: Attaching Chain and Quick Link (Hanging Mount)
NOTE: During this step, determine the hanging length of your fixture by removing chain links, optionally cutting the electrical and ground wire to length. Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy loop (GG) to allow for easy connections in step 7. Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together. Once hanging length is determined, open a chain link at one end of chain (FF) and slip through the chain loop (F). Close the chain links back together with the pliers. Open the quick link (HH) and slip through the chain loop (GG) and the other end of chain (FF). Close the quick link (HH). You can now weave the wires and ground wire through every third chain link (FF), having them exit up through the chain loop (GG) and out the back of the canopy (G).
Visual Description: Diagram shows chain (FF) being attached to chain loop (F). A quick link (HH) is shown attaching chain loop (GG) to chain (FF). Arrows indicate spreading and closing chain links. Wires are shown being routed through the chain.
Step 7: Wiring Connections (Hanging Mount)
Strip 3/8" of insulation from the electrical wire ends. Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.
Visual Description: Diagram shows wire stripping. It illustrates connecting wires using wire nuts (BB), specifically showing a "Ribbed" wire connecting to a "WHITE" supply wire and a "Smooth" wire connecting to a "BLACK" supply wire. A separate connection shows the ground wire being connected.
Step 8: Securing Canopy to Mounting Screws (Hanging Mount)
Pass the screws (AA) through the two holes in the canopy (G). Secure the fixture to the screws (AA) using the two cylinder nuts (EE). Tighten securely.
Visual Description: Diagram shows screws (AA) passing through the canopy (G) and being secured by cylinder nuts (EE).
Step 9: Attaching Glass Shades and Lamps (Hanging Mount)
Attach the glass shade (B) to the fixture (A) using the socket ring (C) to secure it tightly. Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base, SBCFL or SBLED.
Visual Description: Diagram shows glass shade (B) being attached to fixture (A) using socket ring (C). It also shows a lamp being threaded into a socket.
Warranty Information
WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer's sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility. Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.
