Manuals+

Progress Lighting

P400384 5-LT CHANDELIER

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

CAUTION: Risk of fire. Use minimum 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.

WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

  1. Before beginning installation, ensure all parts are included by checking the contents diagrams on page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
  2. Estimated assembly time: 30 minutes.
  3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Package and Hardware Contents

Package Contents

Package Contents Diagram: Shows a table listing parts A (Fixture), B (Socket Ring), C (Glass Shade), D (Cup), and E (Canopy) with quantities 1, 5, 5, 5, 1 respectively. A simple line drawing illustrates the assembled chandelier components.

Hardware Contents (not actual size)

Hardware Contents Diagram: Displays various hardware items with labels: AA (Screw, #8-32, Qty:2), BB (Wire Nut, Qty:3), CC (Round Mounting Plate, Qty:1), DD (Hex Nut, #8-32, Qty:2), EE (Cylinder Nut, #8-32, Qty:2), FF (12" Pipe, 1/8IP, Qty:2), GG (6" Pipe, 1/8IP, Qty:1), HH (Nipple, 1/8IP, Qty:4). The diagram notes 'not actual size'.

Assembly Instructions

Step 1: Prepare Mounting Plate

Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust the screw length according to the fixture canopy depth.

Diagram for Step 1: Shows a round mounting plate with screws and nuts being attached.

Step 2: Mount Fixture Assembly

Attach the prepared mounting plate assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely. Lift up the fixture and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16" [5mm] of threads are showing. This should be enough to mount the fixture as instructed in step 6. Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.

Diagram for Step 2: Shows the mounting plate assembly attached to an electrical box, and the fixture canopy being aligned with screws for adjustment. Includes 'INCORRECT' and 'CORRECT' visual guides for screw length adjustment, showing the 3/16" [5mm] thread exposure.

Step 3: Adjust Fixture Arms

Equally adjust the arms by carefully turning them out from the center.

Diagram for Step 3: Depicts the chandelier arms being carefully spread outwards from the central fixture body.

Step 4: Assemble Hanging Pipes

Determine the hanging length of your fixture by adding or removing stems (pipes FF/GG and nipples HH). The electrical and ground wire may also optionally be cut to length. Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy (E) to allow for easy connections in step 5. Pass wires through pipes (FF/GG) and nipples (HH), tightening pipes as you go to avoid twisting the wires, then tighten the pipe assembly onto fixture (A). Pass wires through up through the canopy (E) and secure it tightly to pipe assembly (FF).

Diagram for Step 4: Shows pipes (FF, GG) and nipples (HH) being threaded together, with electrical wires passing through them. The assembled pipe structure is then shown connecting to the main fixture (A) and passing through the canopy (E), which is then secured to the pipe assembly (FF).

Step 5: Wire Connections

Strip 3/8" of insulation from the electrical wire ends. Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire from the outlet box. Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.

Diagram for Step 5: Illustrates electrical wire connections. It shows stripping insulation from fixture wires (ribbed and smooth) and supply wires (white and black). Wire nuts (BB) are used to connect the ribbed fixture wire to the white supply wire and the smooth fixture wire to the black supply wire. The ground wire connection is also shown, either via a wire nut or to the ground screw on the mounting plate.

Step 6: Secure Fixture Canopy

Pass the screws (AA) through the two holes in the canopy (E). Secure the fixture to the screws (AA) using the two cylinder nuts (EE) provided. Tighten securely in place.

Diagram for Step 6: Shows the fixture canopy (E) being positioned over the mounting screws (AA). Cylinder nuts (EE) are then used to secure the canopy to the screws.

Step 7: Attach Glass Shades and Lamp

Attach the cup (D) and the glass shade (C) to the fixture socket (A) using the socket ring (B). Use the set tool to secure it tightly. Thread lamp (not included) into the fixture socket. Use 60-watt MAX incandescent candelabra base lamp, SBCFL or SBLED.

Diagram for Step 7: Depicts the glass shade (C) and cup (D) being attached to the fixture socket (A) using the socket ring (B). A 'SET TOOL' is shown being used to tighten the socket ring. The diagram also shows a lamp being screwed into the socket.

Warranty Information

WARRANTY AND EXCLUSIVE REMEDY: Progress Lighting products, when properly installed and under normal conditions of use, are warranted to be free from defects in material and workmanship at the time of shipment. All warranty claims must be asserted within one year from the date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer's sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility. Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.

Models: P400384, P400384 Roxobel 5-Light Matte Black Modern Chandelier, Roxobel 5-Light Matte Black Modern Chandelier, 5-Light Matte Black Modern Chandelier, Matte Black Modern Chandelier, Black Modern Chandelier, Modern Chandelier, Chandelier

PDF preview unavailable. Download the PDF instead.

65138825 Nitro PDF PrimoPDF PrimoPDF http://www.primopdf.com

Related Documents

PreviewProgress Lighting P400391 & P400392 Chandelier Installation and Assembly Guide
Detailed installation and assembly instructions for Progress Lighting P400391 (5-Light Chandelier) and P400392 (6-Light Chandelier). Includes safety information, parts list, hardware details, and step-by-step guidance.
PreviewProgress Lighting P400323 & P400324 Chandelier Installation Guide
Official installation and assembly guide for Progress Lighting Laila collection chandeliers (models P400323 and P400324). Includes package contents, hardware, safety information, and step-by-step assembly instructions.
PreviewProgress Lighting P400345/P400349 3-Light Chandelier Installation Guide
Step-by-step installation instructions for the Progress Lighting P400345/P400349 3-Light Chandelier/Convertible fixture. Includes package contents, hardware, safety precautions, care, and assembly steps for ceiling and hanging installations.
PreviewProgress Lighting P400311 4-LT Chandelier Installation Guide
Detailed installation instructions for the Progress Lighting P400311 4-Light Chandelier. This guide covers package contents, hardware, safety, preparation, care, and step-by-step assembly with textual descriptions of diagrams.
PreviewProgress Lighting P400339 12-Light Chandelier Installation Guide
Step-by-step installation instructions and safety information for the Progress Lighting P400339 12-Light Chandelier. Learn how to assemble and install your fixture.
PreviewProgress Lighting P400370 4-LT Chandelier Installation Guide
Detailed installation manual for the Progress Lighting P400370 4-Light Chandelier, including package contents, hardware list, safety information, assembly steps, and warranty details.
PreviewProgress Lighting P400399 20-Light Chandelier Installation Guide
Comprehensive installation instructions and safety information for the Progress Lighting P400399 20-Light Chandelier. Learn how to safely assemble and mount your new fixture.
PreviewProgress Lighting P400395 6-Light Chandelier Assembly Instructions
Comprehensive assembly and installation guide for the Progress Lighting P400395 6-Light Chandelier. Features package contents, hardware details, safety precautions, and step-by-step installation procedures.